Question about Ruud UBHC Air Conditioner

1 Answer

No Power to Circuit Board

Rudd Silhouette II has no power to Circuit Board. Replaced board thinking it blew out but no power. Checked circuitbreaker and is in the on position.

Is there a fuse for this unit that someone can direct me too? When the unit originally failed the circuit break was tripped and I subsequently reset.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 614 Answers

No control voltage 24 volts. The fan board if it has one. sometimes has a five amp auto fuse on it. If not sounds like the transformer. Not hard to replace.

Posted on Jun 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Emerson LF501EM4F that has a blown 2.5A fuse on the power board. I've replaced it with a new fuse and it blew. I've checked all the diodes with a meter and caps are bulging? Jim


The main power supply regulator section circuit fault. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/
It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.
Search the site by type in the "brand name" to your device; [Exclude the model number], in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

Sep 23, 2017 | Emerson Televison & Video

1 Answer

How do I test a control (circuit) board?


You really can’t test a control board, but if you have a separate oven board there is a fuse between the two.

Sep 25, 2017 | Kitchen Ranges

1 Answer

Ruud Silhouette II has power but nothing else.


Sounds like there is a secondary fuse protection, or some wire came off. Did you check for ground?

Dec 03, 2014 | Ruud Heating & Cooling

2 Answers

Rudd silhouette ii blower


Send direct power to the blower by bypassing relay . See if motor runs

If you need further help, reach me via phone at https://www.6ya.com/expert/thomas_092728000e6acb79

Jul 19, 2017 | Ruud UBHC Air Conditioner

1 Answer

I have a Samsung Ductless Air Conditioner. It wil...


i think there is a short circuit in the fan or compressor even in the board.loop check it & say how many amper is there?

May 21, 2010 | Samsung AS18A6RB Air Conditioner

2 Answers

Ruud Silhouette II Fails to Ignite


sounds like you have bad flame sensor or the sensor is in a bad postition. To get eliminate the lockout turn the power off to the unit and back on again. Look at the circuit board light and see what the troubleshooting code is.

Jan 13, 2009 | Heating & Cooling

1 Answer

Power circuit board needs to be replaced


Samsung parts
http://www.partstore.com/Part/Samsung/Samsung/

Jan 29, 2008 | Samsung HCN4226W 42" Rear Projection...

1 Answer

Mdb8750aws dishwasher dead, no front pannel lights, no functions


I just fixed my washer!!! had power to control board. romoved lower panels openned connection box ( one screw) cut and cleaned wires and reconnected to power line that runs to the plug. Did it twice and finally got a good connection started right up. WAS just about to order a new circuit board. SAVED MYSELF $100.00 !!!!!

Dec 05, 2007 | Maytag 24 in. MDB8750AWS Jetclean II...

1 Answer

InFocus X1 power problem


something blew the fuse the first time. if it blew again, the issue remains. something may be arcing. check near the plug, or if there is anything bouncing around in there or a crossed wire.

Nov 26, 2006 | InFocus X1A Multimedia Projector

Not finding what you are looking for?
Ruud UBHC Air Conditioner Logo

Related Topics:

476 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ruud Heating & Cooling Experts

Bill Long

Level 3 Expert

588 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Dennis Boxerman

Level 3 Expert

1262 Answers

Are you a Ruud Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...