Question about Husqvarna Garden

1 Answer

Vibration that I hear and feel in shaft after trimmer warms up

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 1,041 Answers

Sounds like the drive shaft may be broken or weak in one spot. When it heats up, the metal becomes softer, causing the vibration. Have you had the drive shaft off recently?


Posted on Jun 16, 2009

  • Jim Parker
    Jim Parker Jun 18, 2009

    Did this solution solve the problem?




1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Runs great, blower and trimmer heads will not turn/work. Tried using the blower attachment and the fan turned very slow

Contact the consumer desk.

TB22 EC Curved Shaft String Trimmer by Troy-Bilt

Troy?Bilt Products
Rating: 3.7 - ‎232 votes - ‎$99.99 - ‎In stock
25cc, 2-Cycle Gas Trimmer / Attachment-Capable Design ... The TB22 EC gas string trimmer is both JumpStart™ and TrimmerPlus® attachment capable, making ...

Gas Trimmer ' TB635 4-Cycle Curved Shaft ... - Troy-Bilt

Troy?Bilt Products
Rating: 3.3 - ‎32 votes - ‎$179.99 - ‎In stock
The TB635 EC curved shaft gas trimmer with SpringAssist™ technology features the new Click N Trim™ bump head, making line replacement easier than ever. ..... next one they put on - will only run for about 4 seconds. they've had for about 2 ... Both String Trimmer and Edger work great, easy to start and very low vibration.

Dec 09, 2015 | Troy-Bilt 4-Cycle Curve Shaft Gas String...

1 Answer

There's excessive vibration on my TB70SS trimmer. What can I do to correct this?

common with these units is the spindle drive gets damaged causing it's rotation to be off set and causing vibration, look for marks on outer casing around central spindle joint . also check the line holder has not been damaged causing to be offset .worn shaft bearings can also cause this problem.

Jun 26, 2014 | Troy Bilt Tb70ss Gas Trimmer

1 Answer

Engine noise and Vibration

Sounds like your going to be looking for a new motor soon.

Oct 20, 2012 | 2003 Yamaha YZF-R6

1 Answer

Excessive vibration in Ryobi RY30120 trimmer

the center bushings that holds the shaft center are worn and need to change. this damage is caused bu using a to heavy nylon and because of the damaged you will get vibration on all attachments used

Aug 03, 2012 | Ryobi 30 Cubic Centimeter Curved Shaft Gas...

1 Answer

My Husqvarna 125L trimmer makes a terrible grinding sound and vibration along the shaft. What is this?

Could be a damaged bearing in the gear head, could be a bent drive shaft or outer drive tube, clutch drum may have worn the
engine housing and spinning off centre.

Nov 20, 2011 | Husqvarna Forest & Garden 125l 18" Gas...

1 Answer

I installed a new universal line head to my john deere c1200 trimmer. now it does not spin. it worked fine prior to the change. i disconnected the curved portion of the trimmer prior to attaching the new...

The shaft inside the tube is not properly installed either in the clutch near the engine or in the trimmer head itself. Take the head off and make sure the shaft is all the way in so that is is seated in the clutch. You may have to turn it with your fingers until you feel it go in. Next make sure the shaft and head line up. You will need to make sure they line up which you can see if you look at the shaft and head. i hope this helps./

May 15, 2011 | John Deere Garden

1 Answer

Starts ok, will not rev until warmed up and some times dosen't rev freely, air filter clean and plug looks good.

try carb cleaner.if that does not help adjust the idel screw up or faster,but not all the way.Sometimes the screw will back out due to vibration.

May 11, 2011 | Ryobi 30 Cubic Centimeter Curved Shaft Gas...

Not finding what you are looking for?
Garden Logo

Related Topics:

271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Garden Experts

Jim Parker
Jim Parker

Level 3 Expert

1041 Answers

Phil Walker
Phil Walker

Level 3 Expert

608 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Are you a Husqvarna Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides