Question about Fujitsu Siemens Celsius R610 PC Desktop

1 Answer

Configure SCSI hard-drive jumpers

Two problems. 1) My Fujitsu Celsius R610 reboots immediately I turn it off via the sceen controls

2) I want to add another SCSI drive but I can't get a clear idea of how to set the jumpers. A '3D' diagram would help.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 98 Answers

Set one the master and the other slave to the master .that should work.

Posted on Jun 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Computer wont turn off by os


you must reconfigure your power settings in control panel :

go to control panel -> power managment -> and re-set main power button to turn off the computer instead of rebooting

Feb 05, 2014 | Fujitsu Siemens Celsius R610 PC Desktop

1 Answer

Fujitsu celsius r610 error scsi controller


you search on net i think you get best information .

Mar 26, 2013 | Fujitsu Siemens Celsius R610 PC Desktop

1 Answer

XP can't recognize SCSI Ultra320 hard Drive


First, determine if your "motherboard" will support a SCSI hard drive interface. The type of SCSI drives that are available are Wide Ultra SCSI (40MB/sec), Wide Ultra 2 SCSI (80MB/sec), Ultra 160 SCSI (160MB/sec) and Ultra 320 SCSI (320MB/sec). Today's standard for SCSI drives is the SCA SCSI which has an 80 pin female cable to drive information from the drive to the system board.

Set the jumpers. The drive should have jumpers on it that were set by the manufacturer. Setting the jumpers allows the drive to be recognized by your computer's hardware. If the jumpers have not been set, you will need to set the jumper of the primary drive to "Master," and if you are installing a secondary drive, the jumpers would be set to "Slave." The master drive is the drive that the computer boots to first when it starts up. The jumpers are pins located on the block or end of the hard drive.Resetting the BIOS default should make the system recognize the drive. Or Press F6 to install third-party SCSI drivers.

Sep 11, 2012 | Fujitsu (MAT3147NC-P) 147 GB SCSI Ultra320...

1 Answer

Trying to find the jumper settings for a Seagate 36G 80PINS SCSI 15K RPM HDD Hard Drive with an apparent part number 8E036JO (all my Google searches say it's a Maxtor), but the one I have is Seagate....


SCSI hard drives and devices have a jumper setting to configure the SCSI ID.
Each SCSI device must have a different ID.
The jumper/s are set for the following positions across 3 pairs of pins
: : : = SCSI ID = 0 no jumpers - usually for the boot hard drive
: : I = SCSI ID = 1
: I : = SCSI ID = 2
: I I = SCSI ID = 3
I : : = SCSI ID = 4
I : I = SCSI ID = 5
I I : = SCSI ID = 6
I I I = SCSI ID = 7
This gives a total of 8 possible SCSI devices on one SCSI controller.

Aug 25, 2011 | Maxtor 8E036JO 36G 80PINS SCSI 15K RPM HDD...

1 Answer

Hi how can i reset r610 cmos? i taked off the battery and put it again on it's slot but nothing happened


The Fujitsu Siemens Celsius R610 desktop computer uses a Fujitsu D1357 motherboard. (S26361-D1357 actually)

http://uk.ts.fujitsu.com/rl/servicesupport/techsupport/professionalpc/Celsius/R6xx/R6xx.htm#specs


On this page I would like you to go down to the heading - Motherboard, and click on the D1357 to the right.

A PDF file for the motherboard manual will download.

In Bookmarks click on the + sign to the left of -
Overview Board, Jumpers and Connectors.

In the drop down list click on -
Clear CMOS Jumper (J28)

Increase the view size so that you can see it clearly. Click on the + sign at the top of the PDF file.

1) Computer unplugged from power.

2) The jumper goes across the two pins of J28.

(By the default factory settings there is no jumper across these two pins. The jumper may be just sitting on one pin. Kept there to use for this function. {Clearing CMOS settings}
If no jumper is present see if you can borrow one off of a harddrive, etc. Be SURE to put it back on the device afterwards!)

3) Leave the jumper on the two pins for several seconds. I would wait at least five.

4) Remove the jumper. If it was present before, and sitting on just one pin, put it back.

5) Plug the computer back into power. WAIT 1 minute, turn the computer on.

For additional questions please post in a Comment.
Regards,
joecoolvette

Jun 26, 2011 | Fujitsu Siemens Celsius R610 PC Desktop

1 Answer

Operating system not found


If it only shows it sometimes then theres a chance your hard drive is failing. It may also be that there is a disk in the drive that the computer is trying to boot off.
If there are any strange clicking noises coming from the box then it will be the hard drive.

Aug 31, 2009 | Fujitsu Siemens Celsius R610 PC Desktop

3 Answers

Hello, i have a Fujitsu Siemens Celsius R610 PC. I wiped the hard drive and trying to load a fresh MS Windows XP Prof on but it won't let me. Its saying it can't load or see the HD. any thoughts.


In order to fully install windows you need to have the driver loaded for your SCSI controller built into the mother board. Here: http://support.fujitsu-siemens.com/com/support/downloads.html is the website to get the SCSI drivers. Just make a floppy disk with them and when you load windows setup from the disk when it asks you to press F6 to install third party drivers do so. Then just point to the disk and load them up. When windows finishes loading the rest of the drivers and starts the setup process your hard disks should now be accessible.

Jan 10, 2009 | Fujitsu Siemens Celsius R610 PC Desktop

2 Answers

BIOS PASWORD FOR CELSIUS R 610


hi
if u dont knoe the password
u must clear it
u can your clear withyour bios
see the jumper of three pin near cmos cell
set the jumper to 2-3 position then give power too mother bord 3-5times.
then set it to its original position.
then if your pro is same by mistalke.
u can also clear it bye remove cmos cell from its case for 15 minutes.then start pc u not need to enter password.

Mar 28, 2008 | Fujitsu Siemens Celsius R610 PC Desktop

Not finding what you are looking for?
Fujitsu Siemens Celsius R610 PC Desktop Logo

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fujitsu Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Alun Cox

Level 3 Expert

2678 Answers

Computer Links

Level 3 Expert

2386 Answers

Are you a Fujitsu Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...