Question about HP Officejet Pro L7580 All-In-One InkJet Printer

Open Question


Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a canon pixma mp250 and error P07 flashing.Now,I refill blac and colour cartridges,and clean ink absorber,but still flashing P07.How to reset printer? Best regards, Misko

its mean absorber full..(i think)
Check this steps :
1: Unplug power and USB
2: Open door and hold power button.
3: Connect power.
4: Close door, then release power button
5: Connect USB and an press power to use.

1 Press the power button to turn off the printer.

  • 2 Hold the "Stop/Reset" button while pushing the power button. While still holding down the power button, release the "Stop/Reset" button and then push it twice in a row.
  • 3 Wait approximately 20 to 30 seconds until the LED shows 0.
  • 4 Push the "Stop/Reset" button four times in a row.
  • 5 Push the power button twice.
  • 6 Turn off the printer by pushing the power button one more time. The printer is now reset. Next comes resetting the counter on the cartridge.
  • 7 Unplug the power and the USB cables from the printer.
  • 8 Open the cartridge door and hold down the power button.
  • 9 Reconnect the power cables while still holding down the power button.
  • 10 Close the cartridge door and release the power button. The ink cartridge is now reset.

  • Aug 11, 2011 | Canon Pixma Mp250 Allinone Inkjet Photo...

    1 Answer


    Need to replace drum and reset the counter

    (Essentially the cartridge/drum unit should not be in the printer when you reset it)

    1) Open front door
    2) Remove the cartridge/drum unit
    3) Hold down front button until all lights come on
    4) Put cartridge/drum unit back in
    5) Close the front door

    The Drum life should be reset.

    Jul 07, 2011 | Brother HL 2140 Laser Printer

    1 Answer

    Factory reset Brother MFC-7320

    1. Open cartridge cover
    2. Press the button Clear / Back
    3. Press start button
    4. Print number 11
    5. Close cartridge cover

    Now, your printer is returned to the factory settings.

    Jun 07, 2010 | Brother Office Equipment & Supplies

    2 Answers

    How to fix error 1203

    ERROR 1203 LEXMARK ERROR 1200 Error 1203 is an issue that occurs either when a cartridge is bad or the printer cartridge Slot is bad...

    1 - try cleaning the copper contacts of the both carts and cart slot in the printer and try again..
    2 - when error shows up, shut the printers power off; wait one minute and turn it back on press copy.

    Or try

    Reset Factory Defaults on the Dellâ„¢ 964 or 966 Printer

    To reset factory defaults on the printer, perform the following steps:

    1. Press the down arrow button until Maintenance is highlighted and press the Select button.

    2. Press the down arrow button until Reset Defaults is hightlighted and press the Select button.

    3. The printer displays a confirmation message. Highlight Yes and press the Select button

    Some settings such as phone lists, time, date, and country are not changed.

    Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.

    All The Best: Pineworks

    May 15, 2010 | Lexmark X5470 All-In-One InkJet Printer

    1 Answer

    All lights are flashing. Tried turning the printer off. tried resetting. Checked that the doors are closed, cartridge in all the way.

    Try resetting the printer to factory Defaults. First turn off the printer, then open the front cover like if you were to take the toner cartridge2_bing.gif out. Once the front cover is open then push and hold the two buttons on the panel of the printer and turn the printer on. Make sure the front cover is open and that you are pushing the two buttons all the lights will flash2_bing.gif and they will stop at the very bottom light and stay solid once that happens let go of the buttons and close the cover and that should reset the printer. If that does not fix the problem then it could be something wrong with the Controller Board and will probably need to be replaced.

    Jan 26, 2010 | Lexmark E234 Laser Printer

    2 Answers

    I am getting an error message ox841fc379 when I turn on the printer. Please advise

    Your HP PSC 2355 may need to be reset:

    1) Disconnect the USB cable from your computer
    2) Remove the ink cartridges
    3) Unplug the power cord. Wait for at least 1 minute. Plug the unit back in (press the power button if necessary)
    4) Wait for the "Insert Cartridges" message. Reinstall the cartridges
    5) Close the product doors
    6) If you receive a recalibration message, allow the printer to complete this task
    7) Reconnect the USB cable
    8) Try your print job again

    If problems still exist, your product may need servicing by an authorised HP technician.

    Dec 20, 2009 | HP PSC 2355 All-In-One InkJet Printer

    1 Answer

    Brother 1440 has all lights on, and the printer will not print. I took the cartridge out and slid the drum unit corona wire several times; when Ireplaced the drum unit and closed the door the lights did...

    Needs reset procedure

    There's two ways to reset it

    First: Soft Reset
    1. Open front cover.
    2. Hold down button located under LED's until all LED's are lit.
    3. Release button and make sure drum LED is off, then
    4. Close cover

    Second: Factory Reset
    1. Turn the printer off.
    2. Hold in the circular button on the front panel of the printer.
    3. Turn the printer back on.
    4. When the DRUM light is lit by itself let go of the button.
    5. Hold in the circular button on the front panel again.
    6. Once the Alarm light comes on, let go of the button.
    This will perform a factory reset on the printer.

    I hope that's everything you want.
    Please accept this answer if this will help you.
    Thank you for using Fixya.

    Oct 02, 2009 | Brother HL 1440 Laser Printer

    1 Answer

    ''No Cartridge'' Error

    check if the cartridge is a hp cartridge
    if no use a hp cartridge
    if issue stll occurs
    open the cartridge door
    remove the cartridge and the papers from the tray
    close the cartridge door and turn off the printer
    then turn on then printer
    you will get a msg install black cartridge
    open the cartridge door and put the cartridge inside and the papers in the tray and close the cartridge door
    the printer will intiallize and you will get a ready msg on the display of the printer.
    if you still get the msg have the printer serviced

    Feb 03, 2009 | HP LaserJet 3055 All-In-One Printer

    1 Answer

    Error on LCD: Close door and press enter. Latch Carriage.

    This error comes when the cartridges are not installed properly or when the cartridge door is not closed properly. Once remove the cartridges from the all-in-one and reinstall them again in the all-in-one and close the door firmly and check for the result. If the issue persists power cycle the all-in-one and then reset the all-in-one.

    May 29, 2008 | HP Officejet 7130 All-In-One InkJet...

    1 Answer

    Supply Expired!

    Reset the printer to the factory default setting that should resolve the issue, you can provide me the make and the model so i can give you the instructions how to set the printer to default factory settings.

    May 23, 2008 | HP OfficeJet 7110 All-In-One Thermal...

    Not finding what you are looking for?
    HP Officejet Pro L7580 All-In-One InkJet Printer Logo

    Related Topics:

    15 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top HP Office Equipment & Supplies Experts

    Doctor PC
    Doctor PC

    Level 3 Expert

    7733 Answers


    Level 3 Expert

    1089 Answers


    Level 3 Expert

    102366 Answers

    Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides