Question about Garden

1 Answer

Jonsered chainsaw WHAT CAUSES MY JONSERED 625 TO BACKFIRE WHEN I TRY STARTING IT

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Expert
  • 145 Answers

Backfire out the carb? or timing out?? did you have any clutch work done recently? check the flywheel key, maybe the clutch was taken off with a impact gun. backfire out of the carb look up spark screen in your manual or Husqvarna's website (their free manuals)

Posted on Apr 13, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: need to know gas to oil ratio jonsered 535 chainsaw

50:1 is the mixture for the Jonsered 535. I bought mine new around 1991 and it's been a great saw.

Posted on Nov 09, 2009

  • 4088 Answers

SOURCE: how to adjust chain and bar oiler flow

The chain should be adjusted so that the chain can be pulled by hand fairly easily, but doesn't droop from the bar underneath. Oil flow should be set so that a running engine (chain moving fairly fast) will send a thin line of oil off of the tip of the bar (onto a piece of cardboard) with a few moments of running. Hope this helps!

Posted on Feb 27, 2010

Testimonial: "Thanks for advice about oil flow !adjustment needed I think !!"

eugbug
  • 479 Answers

SOURCE: the chain on my Jonsered

The chain on a chainsaw expands during use.This is caused by the heat generated by friction with the timber being cut. The chain should be monitored during use and the slack taken up by the tensioning adjustment screw or knob. You may have to loosen the nuts holding the bar before doing this and then tighten them securely. If these nuts are loose the chain can become slack. If you give me the model of the chainsaw I can try and find a manual and check the tensioning procedure as newer models of chainsaws have either automatic tensioning or have a thumbwheel arrangement for doing this.

Posted on Mar 10, 2011

Testimonial: "Thanks, great information, worked well this morning"

  • 128 Answers

SOURCE: fuel to oil mix for jonsered 490 chainsaw ?

its a 50 - 1 mix of 2 stroke oil to fuel or 2 1/2 ounces of oil to 1 gallon of gas

Posted on Apr 03, 2011

  • 2239 Answers

SOURCE: I have a Jonsered 20"chainsaw.CS2165

The hand guard is secured on the left side with the top l/h starter cover screw part no. 503203419, the right side is held to the brake actuating arm with a 4mm screw part no. 503202512.
Let me know if you need other parts.

Posted on Jun 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am in Tanzania East Africa. Can you advice me how can I buy the Jonsered 2050 turbo piston kit?


get it here
www.lilredbarn.net > PARTS > Chainsaws > Jonsered > Jonsered 2050 Turbo
or here
www.ebay.com > ... > Jonsered Chainsaw Pistons&Cylinder Kits

Apr 06, 2017 | Garden

2 Answers

How do I change the sprocket on my Jonsered 621 chainsaw?


the sprocket is part of the centrifugal clutch assembly
go google and type in ---workshop manual for jonsered chain saws and there are pages of manuals
I opened one page named jonsered 2036 workshop manual --pdf download and it shows how to work on the chainsaw and includes other models in the procedures
that site is www.manualslib.com>brands>jonsered manuals> chainsaws>2036

Sep 26, 2015 | Garden

1 Answer

Oil ratio for my Swedish made jonsered chain saw model 625=2


Using only a high quality 2 cycle oil mix 2.6 ounces of oil to a gallon of fresh gas.

Sep 30, 2014 | Oregon Jonsered 13" Chain Saw Repl. Chain...

1 Answer

Johnsered chainsaw 625


I think a duplicate question… duplicate answer
This thread says a Jonsred 625 is a Husky 61. Post 17 by SawTroll can be taken to the bank. Everyone defers to him regarding specification questions.
http://www.arboristsite.com/showthread.php?t=103127&highlight=jonsered+625
I found an Operators manual here (no IPL):
http://www.tilton.usa.jonsered.com/node246.aspx

There are a number of model 61s starting on page 11. I suggest you contact Husky for clarification of any saw older than 2000. They may even provide the correct IPL for saw (Jonsered owned by Husky).
HusqvarnaUSA.com
http://www.husqvarna.com/us/homeowner/support/download-manuals/
Enter the 3 digit model number (no XPs, Es, just the numbers)
Serial number decode – useful when downloading IPLs and Manuals
06 1500198
06 = year produced – 2006 (single digit before 2000)
15 = week produced - March
00198 = 198th unit Husky produced that week

That said, the 61 has an outboard clutch. This will help you with removal.
R² Drive Link Outboard Clutch by Drivelink.blogspot.com
http://www.youtube.com/watch?v=cdqkIuVNUQc

  1. Check the IPL for your saw to see if any special tools are needed. Poulan clutch removal tool part number 530031112 if needed. Under $5 from many sources,
  2. There are metal piston stops available, when square (almost never) with the piston top these work well, if not square they have been known to punch through the piston. I suggest a length of starter cord or nylon rope be used instead of the piston stop (retain 6" ± so you can remove it). Make sure the piston is near the top of the cylinder before feeding the cord or it can fall through the exhaust port and damage the piston as it rises.
  3. Everyone I have ever removed had a left handed thread (tighten it to loosen it).
HTH
Lou

Jan 12, 2010 | Husqvarna Garden

2 Answers

My Johnsered 625 chainsaw clutch work????


is it a high idle? most chainsaw's chain continues to turn with a high idle.

Jan 12, 2010 | Garden

1 Answer

What gas-oil ratio to use on jonsered 625?


50:1 ratio....Jonsered smokeless is what I would recommend.Ask 5 people what oil to use and you will get 4 different answers.

Nov 17, 2009 | Sport & Outdoor - Others

1 Answer

Choke wont stay in the closed position for starting


Been a while since I saw a Jonsered but I think if you bend the choke linkage a little that it will stay in the choke position.

May 19, 2009 | Standard Oregon Chainsaw Chain For...

Not finding what you are looking for?
Garden Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers

john h

Level 3 Expert

12104 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...