Question about Hobart N50 Stand Mixer

1 Answer

I have a Hobart N50 and am in need of a SS bowl. The bowl pins are 8 7/8" apart. Do they make a replacement bowl for this? I've seen the ones that have 9" bowl pins. Thanks, Ron

Posted by on

  • Gearheadman Jun 20, 2009

    The mixer was dropped during shipping and bent the bowl arm resulting in the difference.

  • Gearheadman Jul 12, 2009

    Thanks Kevin. Send me your email and I'll get you a copy.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Can buy hobart bowls from lots of places, or use the correctly shaped kitchenaid ones, both fit.. i like the lip and thickness of the hobart bowls, bought mine from globe equip.. do u still have the service manual, if so i would be real intrested in it, please

Posted on Jul 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hobart N50 noises


The frequency is the same in all gears.
disconnect the power and invert the mixer and remove the planetary after driving out the taper pin, then you can access the transmission. It may be a rotor shaft bearing in the motor or no grease on the worm gears.
Nice touch with the video.
If you need parts:

Jan 04, 2014 | Hobart N50 Stand Mixer

1 Answer

BBeater scraping back bottom of bowl


Is the planetary still off before the taper pin is in place?

It's a shot in the dark but if everything lines up, I can think of two possibilities:

1. The taper pin in backwards, and
2. The shaft hole in the planetary is out of round.

Mar 20, 2017 | Hobart N50 Stand Mixer

1 Answer

My hobart n50 has no ground on the power cord, also any ideas on where to get parts?


If the ground pin on the cord is missing, you can put a new plug on the end of the cord -- hardware stores have them.

Charlie

Jan 07, 2011 | Hobart N50 Stand Mixer

1 Answer

Hi somenone may describe how I can procede step


after you removed the tapered pin on the plant. you should be able to get it off the mixer main shaft @this point, there is nothing else holding it to the main shaft

Sep 25, 2009 | Hobart N50 Stand Mixer

1 Answer

Hobart N-50 Mixer beater attachment spins but has no resistance


Sounds like the shear pin on the planetary shaft has sheared off. Has the mixer been subjected to a heavy load. Remove the planetary and see if the shear pin is intact otherwise you may have to open up the transmission.

Ron

Jun 04, 2009 | Hobart N50 Stand Mixer

2 Answers

Worm gear hobart slicer


What is the model number?

Apr 06, 2009 | Hobart N50 Stand Mixer

1 Answer

Hobart N50 / KitchenAid Model G: how do i remove planetary?


you need to remove all the back screws then if it doesnt come tap it with arubber mallet it may be seized on

Nov 19, 2008 | Hobart N50 Stand Mixer

1 Answer

Noisy Hobart N50 Mixer


First, there is a double set screw (one on top of the other - if they are both there) towards the back of the planetary.

Remove the first screw, it should have a normal tip, not pointy. Run the mixer in 1st and adjust the screw, first out then in. Then repeat in 3rd. You should clearly hear a difference.

If not, you probably need to repack the grease in the transmission. The proper grease is called "Darina II". It's expensive ~ $35 per mixer.

Apr 13, 2008 | Hobart N50 Stand Mixer

1 Answer

Hobart N50 Tripped


The reset button is to protect over amping the motor. The N-50 is not a very strong unit, (commercially), but you won't break a gear. If you overload the unit, you'll either trip the overload (reset button), or you will break the taper pin that attaches the planetary to the center shaft.

If you're looking for a small commercial unit, and you're in the US, look into the 10 qt Precision Mixer.

Apr 04, 2008 | Hobart N50 Stand Mixer

Not finding what you are looking for?
Hobart N50 Stand Mixer Logo

Related Topics:

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Food Mixers Experts

Ross Keen

Level 3 Expert

1320 Answers

John Tripp
John Tripp

Level 3 Expert

4655 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

1943 Answers

Are you a Hobart Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...