Need users manuel

Here are some potential issues that could be causing the problem:

1. Worn or damaged print hammer: The print hammer is the part of the machine that strikes the ribbon to transfer ink onto the paper. Over time, the print hammer can become worn or damaged, which can cause it to strike the ribbon with less force, resulting in light printing. If you suspect this is the problem, you will need to replace the print hammer.
2. Dirty or misaligned print hammer: Even if the print hammer is not worn or damaged, it can become dirty or misaligned over time, which can affect its ability to transfer ink onto the paper. Clean the print hammer with a soft cloth and make sure it is properly aligned with the ribbon.
3. Worn or damaged ribbon guide: The ribbon guide is the part of the machine that helps guide the ribbon over the print mechanism. If it is worn or damaged, it can cause the ribbon to slip, resulting in light printing. You may need to replace the ribbon guide.
4. Misaligned or dirty print mechanism: The entire print mechanism may need to be cleaned or realigned to ensure that it is making proper contact with the ribbon and paper. Consult the user manual or seek professional assistance to properly realign or clean the print mechanism.
5. Electronic malfunction: If the issue is not related to any physical components, there may be an electronic malfunction that is causing the problem. Seek professional assistance to diagnose and repair any potential electronic issues.

try replacing the ribbon for the printer that prints the reciepts. they do need to be changed after some period of time. Check your owners manuel for instructions.

Hi, you can download the user guide here, which should tell you how to replace the ribbon:

http://www.helpowl.com/manuals/Casio/DR250HD/40705

I'm including this link to the users manual:

http://www.zebra.com/id/zebra/na/en/index/resource_library/manuals.results.html

But here is the basic troubleshooting info for that issue

No print on the label.The media may not be direct thermal media when printing without ribbon (i.e. thermal
transfer). See the test procedure

Determining Thermal Media Types on page 29.
• For thermal transfer printers, the media may not be outside wound or approved for use in
the G-Series printer. See the following ribbon test procedures: Ribbon Test with Adhesive
on page 32

and Ribbon Scratch Test on page 33.
• Is the media loaded correctly? Follow the instructions for

Loading Roll Media on page 11
in the Getting Started section. For printing using transfer ribbon, see

Loading Transfer Ribbon
on page 14.

Locate your printer driver under devices and printers Right click on it and select "Printing Preferences"

Choose the "Advanced Setup" tab

Change media type to "Direct Thermal"

Be sure that "use printer settings" is NOT selected at the top left

Click OK and you should be good.

Note that any labels created prior to this change will need to be changed inside each label under the label setup.

According to the user's manual this message indicates a problem with the ribbon sensor. As a test, set the unit for thermal direct printing and attempt to print a barcode. You will not see the code if yoiu are expecting thermal transfer, but the paper/label should feed like it is printing. That will indicate that the printer is functioning. At this point, the sensor needs to be replaced.

Hope this helps,
Dan

Tally Genicom T 2265 Printer print head. The following information regarding Print Head is taken from Website. Please go through carefully. Print heads are very sensitive from the type of ribbons you use. These textile tapes, used as consumable in dot matrix printers are made by special technologies. They are impregnated with ink and special oils, which lubricate the print head wires during printing. While print head works, the quantity of ink and lubricant in ribbon exhausts, and the quality of printed matter gradually declines. When this quantity goes down below certain limits the ribbon begins wear to threads. These fine textile fibers mix with cellulose filaments from the paper and form a dark gray dust. This is a sure sign that the ribbon is dangerously worn and must be changed with a new one. Otherwise you will soon need a print head repair service. Still not satisfied about those points, please get in touch with local authorized printer service engineer to set right the issue. Have a Nice Day The same problems you may have with "old" ribbons, because after time the lubricants and inks get dry. The usage of "worn" or "dry" ribbon leads to difficult movement of the printhead's wires, its quick wear or crush. If you wish to use your printhead for a long time without any problems, you must use a quality ribbons with an original guarantee. Never use re-inked old ribbons. This surely guides you to print head repair or to buy a new one. It is a good idea to read the User's Guide for your printer, if you have not already done so. If you don't succeed in finding it, then carefully look at your printer and try to find the lever for printhead positioning, it controls the printhead gap. You must adjust manually this gap in correspondence with the number of printed copies.

this machine use the thermal pressure to press out ribbon and card,
so you need check
1) your new installed ribbon is original parts or fake one
2) check again your ribbon install at properate possition and move normally when printing, or reinstall it.
3) check if there is any gap which will lost the presure balnace betwwen printer head and pressure base.
just give you some idea, send any question please
hope you fix it.

You need to go into your "Function" key- do you have the User's Manuel- if not you can go to canonusa.com- I am a USA Canon dealer so i can only refer you to the USA site, go here down load the User's Manuel- I haven't done it in a while but, i do believe you need to go into the Function mode the display "Set-Up" then change output preferences , I think your getting the " Sent " request- trust me get the User's Manuel and read it this should solve your issues you can download it right from the canon Website

change the user account to administrator, to unlock privileges.
That should solve your problem, remember to restart the pc so changes are made in the registry

kind regards and please don't forget to rate us