Question about Welding Tools

Open Question

Miller big blue 350 pipepro 350

Hi! I melted the positive stud on the weld terminal! how do i replace it!! thanks !

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 87 Answers

SOURCE: Hi, starts to weld fine after a few seconds hi

It sounds like you need to change out your SCR chip on your motherboard; Miller makes one that i have installed on all our 350xl's, I don't have the number on hand but i can get it for you tomorrow.

Posted on Oct 20, 2009

Testimonial: "appreciate the help."

luis_david
  • 407 Answers

SOURCE: I have a Miller Big

Hi:
Have you check the fuses? Probably your machine experienced an overload. Check your owners manual on the troubleshoot section. Here's the link to the manual.
http://www.millerwelds.com/om/o480ac_mil.pdf
Good Luck

Posted on Sep 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Miller trailblazer 302 wants to melt a brand new stator within seconds of welding. Any ideas on why? Thanks.


it would appear that there is current or voltage control probably from a dead short in the circuit or a problem voltage control regulator
probably best if you discuss it with the service agents as to what is wrong and get a proper diagnosis

Mar 16, 2017 | Miller Welding Tools

1 Answer

I need tips for my stud welding gun. How can I replace them? Thanks John


https://studweldprod.com/

Stud Welder - Stud Welding Equipment, Gun - Stud Welders Machine

www.eastwood.com > Welding & Fab
  1. Cached
  2. Similar
Stud welding makes more sense. Our stud welder systems each have a stud gun welder that spot-welds a series of pins onto the surface of the dented metal.

What is Stud Welding? ' Sunbelt Stud Welding

www.sunbeltstudwelding.com/studwelding.htm
  1. Cached
  2. Similar
Weld studs come in a variety of designs, threaded, unthreaded, tapped, etc., ... The welding gun is activated and the fastener is welded in a fraction of a second.

Stud Welding Machines and Equipment ' Red-D-Arc Welderentals

www.red-d-arc.com/rental-equipment-subcategories.aspx?sub_cat=180
  1. Cached
  2. Similar
Red-D-Arc offers a range of fully regulated, user-friendly stud welders, stud welding machines and equipment available in single or dual gun versions and ...

Jan 30, 2017 | Welding Tools

1 Answer

Have a 71 miller big 40 won't ark and no power out of plugs put a new ingniter on welded for an hour then shut it off when back the next day and it wooden weld ageen S\N HE802998


hi, you have 2 big resistor with ajustable tab on it,check for visual damage on it and rusted connector or tab,
replace tab at same place if you disasemble it

Feb 16, 2014 | Welding Tools

1 Answer

I need the part number for the termial output and ground for my 302 diesel Trailblazer and a part number for the starter motor for my 400P Big Blue Diesel. Also any suggestions on spare parts I should...


Hi:

Part number for the ground output terminal is MIL 039046, list price is $24.34.
For the Big Blue need to specify what engine/model does your machine has or serial number.

Aug 07, 2011 | Miller Trailblazer 302 Welder Generator...

1 Answer

I have a Miller Big Blue 251D and while welding it died and won't restart.


Hi:
Have you check the fuses? Probably your machine experienced an overload. Check your owners manual on the troubleshoot section. Here's the link to the manual.
http://www.millerwelds.com/om/o480ac_mil.pdf
Good Luck

Jun 15, 2011 | Miller SYNCROWAVE 250 DX TIG RUNNER WELDER...

2 Answers

Miller S-54D 115V digital wire feeder that does not weld right.


Hi Kevin,
Causes of poor penetration: Travel speed too fast, welding current too low,
poor joint design / and or preparation, electrode diameter too large,
wrong type of electrode, excessively long arc length.
Solutions: Decrease travel speed, increase welding current, increase root
opening or decrease rootface, use smaller electrode, use electrode with deeper
penetration characteristics, reduce arc length.

Mar 24, 2010 | Miller Welding Tools

1 Answer

I have a Miller 225G plus. it idles up good and


Take off shroud, look at where the positive lead hooks into the transformer. You may find that the wire has melted, If you are lucky, you can loop it tnough to make a fresh connection. (also check the negitive)

Dec 09, 2009 | Miller MATIC 140 MIG WELDING PKG w/cart...

1 Answer

Improper arcing


A milermatic 350, depending on how old it is.....check the capacitor bank inside. We had the same problem with one of ours ( wouldn't spray arc and was getting weaker) and the caps were bad. When you open it up, look at the caps and if they look like they have been hot....discolored and the plastic covering melted, then just replace them. I know we had trouble getting the correct size, but found some larger ones on ebay.

May 10, 2009 | Welding Tools

Not finding what you are looking for?
Welding Tools Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Welding Tools Experts

Brad Brown

Level 3 Expert

15478 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Bill Boyd

Level 3 Expert

40764 Answers

Are you a Welding Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...