Question about Indesit Washing Machines

1 Answer

Indesit moon washing machine tripping rcd

I have traced the problem to the capacitors and coil at the end of the cable from the mains plug. Im now stuck as to what it could be as it all looks ok

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Tripping rcd usually element.

Posted on Mar 24, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 139 Answers

SOURCE: Earth Fault

IM GUESSING THAT YOU GOT A LEAKY GASKET THATS SPRAYING WATER ONTO YOUR DOOR INTERLOCK SWITCH CHECK TO SSE IF YOU AHVE ANY RIPS OR TEAR IN THE GASKET. DOOR INTERLOCK WOULD BE WORTH CHANGING AS THEY DONT COST MUCH.

Posted on Aug 31, 2006

SOURCE: Hotpoint WMA 48, tripped house rcd, no lights on and water heating noise.

If you are not sure what you are doing, call out an engineer and have the job carried out properly with safety testing at the end of the job!

Posted on Dec 09, 2007

  • 197 Answers

SOURCE: Indesit WIA 121 washing machine,

One of the main problems with Indesit front loaders ( apart from replacing the door interlock switch) is

If the door will not close and click in the lock, then take the door off with a tork screwdriver and take the screws of the inner plastic off the door (make sure you do this on a flat surface) and gently prize off the inner plasic by running round a flat head screwdriver..
Once you have taken off the door and glass bowel - check out the door catch to see if a metal rod has come out of its housing holding the catch and spring in place and refit or replace.
I have come across many door catches like this.

Posted on May 17, 2009

  • 44 Answers

SOURCE: Washing machine tripping RCD

electrical short in m/c.could be heating element. regards

Posted on Jul 30, 2009

  • 25 Answers

SOURCE: Indesit WIXL 143 washing machine noise

there maybe a coin or something stuck between the two drums, when the machine spins fast it lifts the item up, unplug the appliance and remove the botton drum hose to see if you can get it out.

Posted on Apr 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, i go into the test mode and it starts on 18 and when it gets to 14 the house electricity power trips off.Any idea what part do i need to replace?


How can I figure out why my washing machine is tripping the ...

diy.stackexchange.com/.../how-can-i-figure-out-why-my-washing-machi...
Aug 17, 2012 - 110.24872300) washing machine which up to this point has been ...Note what is happening when it trips (is it starting to spin, starting to drain, filling, etc.).... If the outlet trips when the washing machine isn't running and isn't ...

Washing machine tripping RCD « Singletrack Forum

singletrackworld.com/forum/topic/washing-machine-tripping-rcd
Switching on the plug socket that the washing machine's plugged into caused no problems, but switching the machine itself on trips the RCD. ... then its possibly the water fill solenoid as most cycles start with a water fill. ... I've always guessed it is theelectricity/water combo somewhere in the machine so err on the side of ...

Nov 29, 2015 | Washing Machines

1 Answer

Trip switch cuts out when i use washing machine


Main board power circuit fault.disconnect main PCB and reconnect power cable .you can identify the fault. Replace main pcb.

Sep 01, 2014 | Indesit Washing Machines

1 Answer

Hotpoint wmf740 washing machine tripping RCD


try this open the door and then plug it back in when the door is closed its got power so when open the power is really low if it trip after that it will be you main Bord and poss door switch but i will tell you its going to cost cheaper to buy a second hand machine if you have done what i have told you then get a call out but make sure the call out is cheap ok it could be a waste of time ok

Oct 22, 2012 | Hotpoint Washing Machines

1 Answer

Zanussi jet stream iz16s tripping ouy rcd once filled up with


Hello,
It would seem to me that the heating element needs replacing from the information you have supplied especially as it performs most of the other functions like filling and spin and drain.
Good luck

Mar 17, 2010 | Washing Machines

1 Answer

Washing machine tripping RCD


electrical short in m/c.could be heating element. regards

Jul 30, 2009 | Washing Machines

1 Answer

DI 67 Diswasher trips RCD fusebox


either the element is faulty or poss the electrical filter.

Nov 14, 2007 | Indesit 24 in. DI67 Free-standing...

2 Answers

Washing machine blown fuses


Hi - had a similar problem with about 3 different makes of washing machine - the RCD switch on the main household fuse box was continually tripping . Nobody could give me a right answer . Eventually ended up with a Hotpoint . Felt sorry for the delivery guys from the electrical retailers having to keep dragging machines in and out .

May 07, 2007 | Indesit WA 115 Front Load Washer

2 Answers

Tripping out RCD


i had this probem and apparently there's a 'float switch' in the bottom of the machine. This switch is a safety cut off and when activated can not just stop the machine but trip the electrics in the house. the reason for it activating is when food clogs up the drainage bit water can not drain and fills up the bottom of the machine. this then activates the 'float switch' as a kind of safety cut off.
the way to sort it is to disconect the machine from the mains and drain and water. empty the clogged up food from the drain bit. then tip the machine back and a load of water will pour out (may need a load of towels for this bit or take the machine out the back and do it)
once this is done, plug it all back in and give it a try - works for my machine, good luck.

Aug 25, 2006 | Indesit 24 in. D63 Free-standing...

2 Answers

Earth Fault


IM GUESSING THAT YOU GOT A LEAKY GASKET THATS SPRAYING WATER ONTO YOUR DOOR INTERLOCK SWITCH CHECK TO SSE IF YOU AHVE ANY RIPS OR TEAR IN THE GASKET. DOOR INTERLOCK WOULD BE WORTH CHANGING AS THEY DONT COST MUCH.

Jul 24, 2006 | Hotpoint Aquarius WD640 Front Load...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Indesit Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1466 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Darren Moxam
Darren Moxam

Level 2 Expert

67 Answers

Are you an Indesit Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...