Question about Dishwashers

1 Answer

Howe do you get the ultra wash module out of kenmore dish washer model665.749622

Dropped a ring into dish washer can't get the wash module out

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,511 Answers

You will need the schematic manual that takes you through the steps when removing and replacing parts. Kenmore may have one free on line, and you will need to go the web site for that information.

Posted on Mar 18, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Kenmore Elite Ultra Wash Dishwasher keeps shutting off before entering the cycle. I have repositioned dishes, even emptied it, changed cycle and tried everything. When I press the start light flashes...


I too had problems with the Kenmore Elite (aka Bosch). The issue was solved by replacing the Lock Sensor on the door. After replacing the sensor the dishwasher has been working. Hope this helps.

Oct 08, 2013 | Kenmore Elite 24" Built-In Dishwasher with...

1 Answer

The soap despenser is broken. looks like the spring is inside the holder and it will not close....stays open at all times. model number for our dish washer is 665.13842k601.Kenmore ultra wash. is this an...


Hi,
There are three common problems that cause the Soap Dispenser or Cup not toopen. I have a tip that will explain these problems in detail....

Dishwasher Repair Problem Detergent Cup does not Open

heatman101 '';
';';
';
';';

Aug 01, 2011 | Kenmore 24 in. 15932 Built-in Dishwasher

1 Answer

Need a owners manual for a ultra wash II dish washer model # 1581591


Is this the correct dishwasher?


http://www.searspartsdirect.com/partsdirect/part-model/Kenmore-Parts/Dishwasher-Parts/Model-6651581591/0582/0130000?searchedModel=1581591&blt=

Feb 01, 2011 | Kenmore Dishwashers

1 Answer

Not cleaning properly


take a good look at the two spinning washers they are easy to remove i would suspect they are clogged clean and replace.adrian,,,,

Jul 14, 2010 | Kenmore Dishwashers

1 Answer

Brand new ultra wash HE stuck in one cycle


Does it fill with HOT water (check after fill stops)? Did Sears install the washer? If so, have them troubleshoot the problem. It's obviously bringing water in. Are there any error lights or codes? May need to replace the control unit.

Jul 14, 2009 | Dishwashers

1 Answer

Smelly dishes from Kenmore Ultra Wash


If you post the model number of your dishwasher plus its approximate age (in years) I can help more.

But the most common cause is a weakening pump motor. On many dishwashers, the wash pump motor is also the drain motor. Replacing that motor / pump assembly will solve the problem. While you are replacing the pump, check the heating element to confirm that it is not shorted out or broken.

For now, add a cap full of bleach to the water _after_ the initial dishwasher fill cycle ends and the wash cycle begins. White vinegar would also work, but this will not fix your problem.

Good Luck!

May 04, 2009 | Kenmore 24 in. 15932 Built-in Dishwasher

1 Answer

Kenmore Ultra Wash 110733601 - dishes too hot!!!


Well what I will need you to do is to check your water temp....with a cooking thermometer....it should not be hotter than 120....then place the same probe in the dishwasher and it should NEVER get above 150 as this could and will damage certain dishes....Tupperware...etc.. If the temp going into the DW is greater than 120 you will need to turn it down further...as the DW has an assist feature in it that heats the water further...you may also need to try the wash in a different mode if there is one say without heat dry.....etc. unfortunately this is all i can offer ..I spent about an hour searching for your product manual...(and I am very versed in the internet search process)...but your Kenmore 110 (thiese first 3 digits refer to the actual maker since sears does not make ANY of there own appliances...and this one is Whirlpool) but I colud not find it.

I hope this helps......good luck....thank you for rating my effort....The Fang.

Mar 29, 2009 | Kenmore 1621 - Multiple Color Dishwasher

1 Answer

Washer won't drain


Dear cbringer,
I have the same washer. I have had the same problem with it. It's the timer module. You can get additional help from http://www.repairclinic.com.

Hope This Helps,
Jay

Mar 12, 2009 | Kenmore Washing Machines

2 Answers

Need to remove wash module


You should be able to hold the spray arm and unscrew the center section to remove the entire assembly. Be aware of any washers or other parts that need to be re-installed when putting it back on.

Jun 13, 2007 | Kenmore 24 in. 16032 Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Owen Barnes

Level 3 Expert

867 Answers

Brad Brown

Level 3 Expert

15478 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...