Question about Car Audio & Video

1 Answer

Kenwood manual helloim looking for a free manual download of the car amp model KAC-748please help me

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 328 Answers

Here is a free manual, just download it.
http://www.retrevo.com/search/v2/jsp/downloadPage.jsp?doc=e73fb2d3135db11ba752b002abe6f643&q=Kenwood+KAC-748

Posted on Oct 30, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenwood repair manual


I have the Kenwood KAC-9152D Repair Owners Manual. This is my E-Mail address. canalv11@gmail.com send my a e-mail. & I will e-mail back 2 U w/the Manual ATTACHED

Dec 21, 2011 | Kenwood KAC-9152D Car Audio Amplifier

1 Answer

Leads for old kenwood car stereo amps


Hey wdalley69, I've got the KAC-8070. My setup has the crossover module for it.

Oct 27, 2009 | Kenwood Car Audio & Video

4 Answers

KAC-8070 kenwood 4-channel power amp


Audio section
Max Power Output (4 ohms, 1kHz)
Rear 70W + 70W
Front 35W + 35W
Max Power Output (4 ohms, 1kHz, 10% THD)
Rear 45W + 45W
Front 25W + 25W
Max Power Output (4 ohms, 1kHz, 1& THD)
Rear 37W + 37W
Front 20W + 20W
Frequency Response (-3dB)
Rear 2 Hz ~ 100 kHz
Front 5 Hz ~ 50 kHz

Sep 27, 2009 | Kenwood KAC-8101D Car Audio Amplifier

1 Answer

HAVE A KENWOOD AMP MODEL KAC-9102D . iT KEEPS SHUTTING OFF WHEN i TURN THE RADIO LOUD. ANY SUGGESTIONS


either bad ohm load or over heat if the ohs on the speaker wires to the amp are lower than specified use in the manual it will act funny cause it is pusing harder than its meant to and if it gets too hot either bad location or bad amp you can try turning the gain down a little until the amp stays on constantly at high volume

May 18, 2009 | Kenwood KAC-9152D Car Audio Amplifier

1 Answer

To bridge a Kenwood KAC-9102D


Hello laurogleal,

The Kenwood KAC-9102D is a mono amp. There is no bridging. Having two sets of terminals is just a more convenient way of connecting two subwoofers. The amp is stable down to 2 ohms impedance, so it is safe to run 2 4 ohm loads in parallel.

Hope this helps.

Apr 28, 2009 | Kenwood KAC-9102D Car Audio Amplifier

1 Answer

Connecting subwoofer to kac-7201 kenwood amp


from your sub connect one short piece of cable from + on one side to - on the other side using the same diameter cable as you are running to the sub from amp . this will leave you with + and - on opposite sides of speaker these will then run to the amp +to+ and - to- on the mono side of connetor which is one left + and one - right and the amp switched to bridged

Mar 22, 2009 | Kenwood KAC-7201 Car Audio Amplifier

1 Answer

Kenwood KAC-PS201T


The first thing you must do is to confirm that you have voltage at the amp. Just because the fuses look good, that doesn't mean you're getting power to the amp.

With your multimeter set to DC volts, the black meter lead on the ground terminal of the amp and the head unit on (so the amp will have remote voltage applied), touch the red lead alternately to the B+ and remote terminals of the amp. If the voltage is below ~11 volts, you need to check the wiring feeding whichever line is too low.

Jan 21, 2008 | Kenwood KAC-X201T Car Audio Amplifier

1 Answer

Car amp power problem


hi your assumption is wrong the light blinks for meny diffrent reasons: 1) power is too low - check the battery of the car 2) connections are wrong 3) the AMP is in safe mode here is the manual of the product: http://kenwood.nl.nt.ims.hr/languages/EN/support/manuals/KAC-849~749S%20(EN).pdf here is the home page: http://www.kenwoodeurope.com/support/Menu2.aspx?men=2&M1=3 good luck

Mar 21, 2006 | Kenwood KAC-749S Car Audio Amplifier

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

578 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4919 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

78289 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...