Question about Whirlpool LSB6200KQ Top Load Washer

1 Answer

Spins during agitation makes noise

My washer while agitating  works slowly but makes awful noises and sometimes on spin cycle

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert that has over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 327 Answers
Re: spins during agitation makes noise

Welcome to FIxya

I would check the belt and i would also check the bearing

hard to help you out with out seeing it but i would check those first ....

hope this helps out have a good day :)

Posted on Jul 16, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Know when clutch going bad

Needs agitator dogs in agitator.

Mar 13, 2014 | Whirlpool Washing Machines

1 Answer

I have a eterna EWA5600G king size washer that is making a very loud sceaching sound

check the drive belt from the motor to the gearbox it might be louse that would make it screach and week agitating

Dec 01, 2011 | Washing Machines

1 Answer

Doesn't agitate and spin cycle work when reset

you have a worn motor coupler
you can order a new one at sears
and its a ver y easy repair

Oct 06, 2009 | Kenmore 3.2 cu. ft. Plus Top Load Washer

1 Answer

Making an awful ratcheting noise during aggitation and spin cycles

Under the agitator there is a rachet mechanism that works the agitator. If it is stripped, it will skip until the next good tooth.. when it fails entirely the agitater will stop going back and forth. Its nylon and age along with overloading hastens its dearg.. If you can get the parts you can replace it yourself without difficulty. There is a single bolt in the center of the agitator top . Remove and loft agiyator straight up.

Jun 03, 2009 | Maytag Legacy Series Top Load Washer

1 Answer

Noise when stopping after spin cycle or open lid (after moving)

check hub nut, it is likely loose, its under the agitator. top pops off agitator and bolt hold agitator down.

Jan 04, 2009 | Whirlpool Inglis IP4400 Washer

1 Answer

Loud grinding motor protesting humming w/no spinning or agitating

The drum/agitator bearings are bad I believe, or the gearbox has been damaged. This is an expensive repair. I would strongly consider buying a new washer. This is a great time to buy appliances since the stores are really competing, and the prices are at their lowest.


Dec 14, 2008 | Kenmore 22422 Top Load Washer

1 Answer

Agitator fall off and knocking noise during spin cycle

there should be a rubber washer with the bolt. if it is missing the bolt may back of during agitation. also the threads on the transimision may be stripped. Some Green lock tight found in most hard ware stores should help. the knocking noise is probably due the agitator coming loose.

Sep 16, 2007 | Maytag PAV2300 Top Load Washer

1 Answer

Agitator not turning during cycle

Well, it sounds like you've done your homework. My first suspect would have been the agitator dogs too, but you said they were fine. Another likely suspect would have been the motor coupler, but you said the washer spins during the spin cycle. If the coupler was bad the unit would fill, but wouldn't agitate or spin. Plus, it would make an awful noise. I would have also suspected a clutch assembly, but you said the wash tub can spin. Normally, when the clutch goes bad, the drum won't spin, or spins slow. Another suspect could have been a bad lid switch, but the washer would have filled and stopped, without agitating or spinning. The only remaining suspect that I'm aware of is the gear case (transmission). Checking under the washer can give you some clues. Normally, when a gear case starts to go bad, they leak an amber colored oil. You may find puddles or drips under the washer. If you see no signs of oil the gear case could still be defective, however. But, before you go through all the trouble, double check the agitator one more time. Completely remove it from the tub and check the under side to ensure the grooves that grip the top of the gear case shaft have not been worn smooth. I hope this may have been some help to you.

Jul 09, 2007 | Kenmore 24032\24036 Top Load Washer

Not finding what you are looking for?
Whirlpool LSB6200KQ Top Load Washer Logo

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides