Question about JVC HR-S9500 S-VHS VCR

1 Answer

Hrs9500 stop after 6 sec

Hrs9500 go in stand bye after 6 sec .
help me thank you.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: hrs9500 stop after 6 sec

Also have te same problem with a S9700.
Switches to stand by after 6 seconds again and again.

Please help!!!

Posted on Apr 09, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I pushed the otr button by mistake and now I can not stop it from recording or turn off the vcr.

OTR stands for one touch record, each press of the button will increase the recording time. However if you keep pressing the button it should go back to "0" and stop!

Feb 22, 2010 | Emerson EWV603 VHS VCR

1 Answer

VCR Lock Activated message appears when I hit Play. Why and how do I get rid of it so I can play a tape?

<b><font size="1" face="Helvetica-Bold"><font size="1" face="Helvetica-Bold"> To turn on, </b></font></font><font size="1" face="Helvetica"><font size="1" face="Helvetica">hold down<br /> REC on the VCR in Stop<br /> mode with no tape<br /> inserted for 7 sec.<br /> (Please ignore the NO<br /> CASSETTE warning.)<br /></font></font><b><font size="1" face="Helvetica-Bold"><font size="1" face="Helvetica-Bold"> To turn off, </b></font></font><font size="1" face="Helvetica"><font size="1" face="Helvetica">repeat above<br /></font></font><!-- from fixya rte -->

Nov 22, 2009 | Panasonic PV-V4022 VHS VCR

1 Answer

Vidio player toshiba v631 snowy all the time stand by

You need to clean the video heads and change the push buttons that not work

Jul 05, 2009 | VCRs

2 Answers

When tape is inserted the unit starts beeping and I have to eject tape. Tapes will not play, rewind, fast forward or record? How can I fix this?

The beeping indicates that an error has occurred and that the unit has been disabled because operation could damage the unit further. To determine what the problem is- Turn unit off. While holding the STOP button, turn back on and continue to hold the button for 8 sec, then let go. Press display and you will get an error code on the monitor, for instance, C:21:00 error code (the most common code I get) indicates a condensation problem. If this is the code you get then leave the unit open in a dry place for 24 hours or so, and it should dry out the dew sensor and clear the code. The unit will hold up to 6 error codes in the order that they occur, rotate the wheel to cycle through the codes. Codes are displayed as - C:XX:XX. If you get a code other than C:21:00, then google the code,(Sony C:XX:XX) and the description will probably come up. Good luck.

Jun 28, 2009 | Sony EVO-250 Hi8 VCR

1 Answer

I'm looking for the manual for a Mitsubishi VCR HSU447 with the remote control RM75502 so I can program my TV to it. Thanks

1.- Turn off your TV
2.- On the remote control, set the VCR/TV slide switch to TV position.
3.- While holding in SP/EP button, press the code button listed below that corresponds to the brand of your TV
4.- Press TV POWER on the remote control. Once your TV has turned on, your remote is set up to operate your brand

Brand of TV Brand Code Button
Mitsubishi 1,2,3
Fisher 0
Goldstar 2,9
Hitachi 8
Magnavox 4
NEC 2,9
Pioneer 6
Philips 4
Sanyo 0
Sharp 3,5
Toshiba 7
Zenith INPUT
I finnaly found my VCR Manual, and I'm glad to share this info with you, because I was looking for the manual all
over the web and FOUND NOTHING!. Bye!

Mar 15, 2009 | Mitsubishi VCRs

1 Answer

Plays for 3 secs, stops, and then ejects

This unit needs to have the "idler" changed as well as the belts. Over time, the internal rubber parts get hard ans slippery. There are safety checks inside that will stop the unit when problems are detected. With a slipppery idler assembly, the tape does not get wound into the cassette after passing the heads. Rather than have the tape collect inside and be destroyed, the unit stops. This is a relatively simple repair that any shop should be able to perform. Expect a parts cost in the $35 range. In my opinion, this unit is worth the repair as it will continue to provide service to you for years to come. New replacement units tend to last only a year or two.


Dec 30, 2008 | Mitsubishi HS-U770 S-VHS VCR

1 Answer

3-4 switch

1. Set tv to channel 4
2. insert a pre-recorded tape into vcr. play once to start playback.
4. after a few seconds press play on the vcr for 3 sec you will see a playback picture.
when a picture doesn't appear on the tv screen repeat step 4.
5. press stop to stop playback.

Mar 16, 2008 | Sanyo VWM-950 VHS VCR

1 Answer


This is not repairable

Dec 28, 2007 | VCRs

1 Answer

Aiwa gx 1100 vcr

This is bad failure and not repairable in this model

Dec 28, 2007 | VCRs

2 Answers

How to unactivate 'vcr lock' ?

Generally, if you aim the remote at the VCR with the STOP button pressed, for around 10 seconds, the VCR gets 'unlocked'. Try it.

Feb 25, 2007 | Panasonic PV-7451 VHS VCR

Not finding what you are looking for?

Related Topics:

227 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC VCRs Experts


Level 3 Expert

4518 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

alexander woolfolk
alexander woolfolk

Level 2 Expert

276 Answers

Are you a JVC VCR Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides