Question about Mitsubishi WS-55819 55" Rear Projection Television

1 Answer

Convergence Problems My WS-55819 intermittently has horizontal convergence issues. After the television is on for a while, the convergence remains OK in the center of the picture but towards the left and right sides of the screen, the reds, greens, and blues don't line up. In fact, the reds are too high on the left and too low on the right. It will intermittently "snap" back into place and then just as quickly snap out of convergence. Also, as it snaps in and out of convergence, there are numerous horizontal black "noise" lines going across the screen.Any ideas of what to check or replace?

Posted by on

  • 1 more comment 
  • scottupland Dec 11, 2007

    Where can i get the ICs and how hard are they to install?

  • Greenmachine Dec 24, 2007

    Thanks Joe TV!!

  • Anonymous Mar 21, 2014

    Correct program on left Black or lines on right half

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 39 Answers

GREEN-YOU HAVE TWO STK392570 CONVERGENCE ICS' GETTING READY TO FAIL.SOME FOLKS HAVE REPLACED THEM ON THEIR OWN,OR YOU CAN GET A REPAIR TECH TO DO IT FOR AROUND 300.00$.JOE TV

Posted on Nov 29, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix the 2,2 error on the ws-55819?


install the convergence repair kit for your model. The 22 error is almost always caused by shorted Convergence ICs and blown picos. You can get the convergence repair kit for your model at www.tvrepairworld.com

Aug 05, 2011 | Mitsubishi WS-55819 55" Rear Projection...

1 Answer

I have a ws-55819. the picture is out of focus, more so on the left and right, less out of focus in the middle. Its like there are 3 separate pictures, out of alignment


Thats caused by a failed convergence IC. You can get the convergence repair kit for your model from www.tvrepairworld.com The kit contains the parts and the CD with instructions for the repair.

Jun 06, 2011 | Mitsubishi WS-55819 55" Rear Projection...

1 Answer

My picture is awful! lines don't seem to converge even when I try to do it manually. Everything is doubled. Can't even read the score when there is a basketbal game on! Any ideas or help would be...


Ur tv is 100% have a convergence problems,it dead.The tv colors lines R,G,B mis alignment,have colors shadows pictures or 3D pictures look alike.The tv convergence board the 2 STK convergence ICS and some or all it resistors are dead.These parts on the tv convergence board,must be replaced to solved the tv picture convergence problems.The shop,will cost u like $300-350 for parts and labors.

Oct 28, 2010 | Mitsubishi WS-55819 55" Rear Projection...

1 Answer

Intermittment convergence problems. Color overlays appearing blur


yheshospot,

You have a bad convergence circuit. I have a tip at http://www.fixya.com/support/r4220499-change_projection_tv_convergence_ics which explains how to correct the problem and where to get the parts at the best price.

Thanks for using FixYa and for the great rating.

hardrocko

Apr 05, 2010 | Mitsubishi WS-65809 65" Rear Projection...

1 Answer

Can not align red even though convergence board WS-55819


Did you replace the center board with the STK-392-570 chips or the Digital convergence board mounted on it?


98% of the time if you have a convergence problem it is on the center board---the small board on the left under the metal shield box stores and controls the convergence of this set.


WHICH DID YOU REPLACE?

I am here to help----I have fixed hundreds of Mitsubishi sets with convergence troubles.

Regards, SD TECH

Oct 28, 2009 | Mitsubishi WS-55819 55" Rear Projection...

1 Answer

Convergence


best place to get them with instalation instructions included is the following link. you need two STK392-570 ICs
http://servicemanuals.vstore.ca/

Jun 17, 2008 | Mitsubishi WS-55819 55" Rear Projection...

1 Answer

Mitsubishi WS 55819 with a convergence


CEM-NO, BOTH ICS' WORK ALL 3 CRT YOKES.YOU EITHER NEED TO REALIGN THE RED IN FACTORY CONVERGENCE MODE OR YOU HAVE A RESISTOR THAT HAS FAILED.THE LATTER YOU MAY ACTUALLY BE ABLE TO SEE IF YOU LOOK CLOSELY.OH, ALWAYS DOUBLE CK. YOUR SOLDER CONNCETIONS.GOOD LUCK. JOE TV

Nov 22, 2007 | Mitsubishi WS-55819 55" Rear Projection...

1 Answer

Convergence problems WS-55807


On this model if the fuses that protect the convergence circuit would open up, then the set would not come on. The convergence ICs probably have a cracked solder joint on the foil side of the circuit board.Re-flowing the the solder would help. I will always replace the convergence ICs when doing this job. The labor remains the same and you will have to pay a few extra bucks for the parts. Hope this helps.

May 12, 2007 | Mitsubishi WS-55807 TV

Not finding what you are looking for?
Mitsubishi WS-55819 55" Rear Projection Television Logo

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1230 Answers

The Knight
The Knight

Level 3 Expert

75846 Answers

Jaime Hernandez

Level 3 Expert

2336 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...