Question about Pioneer PureVision Pro-800HD 43 in. Plasma HDTV

2 Answers

Pioneer plasma no picture with blinking red light

Green light comes on momentarily then back to off and red light flashes.

Posted by on

  • 6 more comments 
  • Anonymous Jan 02, 2008

    no power blinking red light after momentary green light

  • Anonymous Jan 21, 2008

    Picture will go blank & red light flashes one time & then 4 times.

    when i disconect the power & turn the tv on again (manually) the picture

    comes back. sometimes this has to be done several times

  • Anonymous Feb 13, 2008

    same as sonnybear's plasma

  • flippo5 Aug 24, 2008

    Same with my 50" plasma Pioneer - unplug power or turn off main power switch then replug in or turn on main power and switch on regular power button - the green light comes on for 3 - 4 secs - then a faint
    pop" then back to blinking red light and no picture nor back light.



  • BlakeVel85 Dec 22, 2008

    Picture on the tv went out..I turned off the unit and red light came on. Then proceeded to turn the unit back on and still zero picture and green light appeared for a few seconds and then went off...Is this the supply assembly board?

  • susiejean Jan 18, 2009

    My pioneer Pro 800HD flat screen would blink off and on. and after doing this about 5 times it will completely shut off. We still have sound but the screen red light is no on with no picture. After a few minutes we can shut the screen on/off buttonto the off position, then back to on then push the standby on button, picture will reappear but only for a short while, sending us through the sequence again.We can not keep the picture on, we have cleaned the air vents and there is no condensation

  • richardkotov May 18, 2009

    is this something i can change myself

  • Anonymous Mar 24, 2014

    I have blinking lights (red and green) on the panel. I don t notice any problems but it is annoying...

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

This requires a replacement of the power supply board. This is per Pioneer tech support whom resolved my issue when I called. Hope this helps!

Posted on Jul 10, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

If you have this problem im sorry to anounce but you will have to contact pioneer to get it fixed because the company will not send out a new part to your closest technician shop i dont know why .... i think its just a quick way to make money really but search pioneer on google and you will get the info you need

Posted on Jan 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pioneer plasma tv model pdp436pg


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit stage inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power led, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. Viewing it in "Mosaic" will make surf easy.
http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience.

Apr 10, 2014 | Pioneer PDP-436RXE 42 in. HDTV-Ready...

1 Answer

Pioneer pdp-505cmx both red and green lights stay on - no picture - any ideas?


After replacing the power supply board, it is necessary and a must to adjust its Va & Vs voltages. These details will be there on its panel label. If you wish to get some details, check the site linked here. http://electronicshelponline.blogspot.com/ Pull up older posts. Without adjusting these voltages properly, might make the Plasma Display defective.

Jan 01, 2014 | Pioneer PDP-505CMX 50 in. Plasma...

1 Answer

Pioneer Elite. Loud popping sound and picture disappeared


Power supply board is dead.The board where the power a/c cord plug into it.Replace the power supply board.Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish power supply board for the replacement.

May 30, 2010 | Pioneer Elite PRO-1140HD 50 in. Plasma...

1 Answer

Power button flashes red. TV comes on momentarily


this is a inverter board defective. please change-it

Oct 31, 2009 | Panasonic TH37PX60 37 in. Plasma...

1 Answer

Red blinking light


same problem, red blinking light in series of 5 flashes

May 30, 2009 | Pioneer PureVision Pro-1000HD 50 in....

1 Answer

Wont turn on red light flashes


The error code of 2x red flashes tells me you need a Y DRIVE ASSY and the part number is AWZ6649. It should be replaced by a Technician thou.
Hope this hleps

Mar 29, 2009 | Pioneer PDP-4270XD 42 in. HD-Ready Plasma...

1 Answer

Green blnking light on pioneer plasma - Picture does not come on


You can try a hard reset : Unplug TV from AC mains and remove all cables from TV. Wait about 30 minutes and replug to AC power and redo the cabling. Switch on the TV and see if it works..


Good luck..

Nov 23, 2008 | Pioneer PureVision PDP-5030HD 50 in....

3 Answers

Pioneer pdp 502mx goes to standby no picture after power on


Contact Pioneer at 1-800-421-1404 about getting an in-home power supply replacement. This is a known issue with some plasma displays. Some of you would experience a loud pop and then the power supply fails. You get a red light below the ON button, when you press on, the red light will turn green for a second and then back to red. The plasma display will not turn on after the power supply fails. Call Pioneer at 1-800-421-1404.
Brought to you by http://abstravel.com and http://reservaciones.com

May 23, 2008 | Pioneer PureVision PDP-502 50 in. Plasma...

1 Answer

Pioneer Plamsa CMX 43"


pioneer customer service: 800-228-7221

C-Dog

Feb 10, 2008 | Pioneer PureVision PDP-4340HD 43 in....

1 Answer

Returns to standby


Green flashing 3 times = digital DC - DC converter fault
Red flashing 3 times = scan circuit fault

Oct 31, 2007 | Pioneer PureVision PDP-5040HD 50 in....

Not finding what you are looking for?
Pioneer PureVision Pro-800HD 43 in. Plasma HDTV Logo

Related Topics:

3,775 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Televison & Video Experts

The Knight
The Knight

Level 3 Expert

72230 Answers

Jaime Hernandez

Level 3 Expert

2296 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Are you a Pioneer Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...