Question about Sony PlayStation 2 (PS2) Console

1 Answer

Smae thin it wont read i took it appart and air cleand it hasent turned on all i get is a red light and i press the buttonand it wont turn on is there a part missin if ya can suggest me somthun that would be apprictable

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 47 Answers

Did it turn on Prior to you taking it apart?  If so then it is most likely the ribbon cable between the switch and the mainboard.

Posted on Oct 28, 2007


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a new red shed windmill and the lights wont work

I had the same problem. Look somewhere under the solar panels on the wind mill. You will find one or two buttons. This will control the lights. You just need to press them to turn them on. It took me awhile to find this, but they are around the solar charging panels.

Aug 07, 2014 | Red Shed Windmill, 10 ft

1 Answer

Wont start at all

If you have no light you can't even hot wire it sounds like the ignition switch is bad in the start and run positions.

Jan 30, 2014 | 2005 Yamaha YZF-R6

1 Answer

My yz125 2stoke 06 wont start

were can i fineceder
the fuel fillter on 2005 isuzu as

Apr 05, 2013 | Yamaha YZ 125 Motorcycles

1 Answer

Why is my Optio mx4 not showing any picture? the screen works but It looks like the lens eye dosent see anything. the menu comes up and the screen itself is fine but the picture looks like the snow on an...

I dropped the camera and got the smae problem, until I read somewhere in this site that open the camera and then tapping on the ring around the lens while power on and off several times, it will work again. I did for me. I took it appart with phillips screwdriver and I used a hard rubber caulk spreader to tap it; it has some weight but will not damage the lens if its it by mistake. Try this and will be surprised. I am the 3rd person I have read that solved it doing this. Good luck.

Dec 06, 2010 | Pentax Optio MX4 Digital Camera

1 Answer

My ionic breeze s1867 turns on and off will not stay on

I have the same problem and haven't been able to fix it. However, others have had the same problem and have posted their solutions. The sizzling sound is caused by electrical arching between the plates and one or both of the two tungsten wires that are run parallel to the plates (if you turn off all the lights and wait for your eyes to adjust to the dark before turning on the Ionic Breeze, it's a pretty cool light show!) Here are things found by others to cause the arching and what they did to fix the problem:
  • --dirt, lint, or tiny hairs stuck somewhere (usually towards the top or bottom of the plates or wire, and maybe in the grid contact points). Clean it better. Using canned air can help blow out the problem.
  • --water droplets. Make certain there is no moisture anywhere when you put the grid (plates) back in. Using canned air can help dry hard to reach areas.
  • --burn marks or melted plastic. These indicates a short circuit. Says dnewcombe1: "There is a feeler bracket that guides the two rear thin wires while the cartridge is being inserted. This "feeler" can melt and become disarranged." You can't fix this issue.
  • --build up on the ionizing wires. Clean them. It's hard. I took mine apart and used steel wool.

Mar 02, 2010 | Sharper Image Ionic Breeze® Quadra® 4.0...

1 Answer

Ps3 wont turn on???

Your system is getting hot......Clean the dust from the unit with a vacume...not a can of air, Canned air will only push the dirt further into the unit. also you can buy an intercooler for the ps3 nyco makes one that actually forms to the ps3

Sep 30, 2009 | Sony Playstation 3 (PS3) Console

1 Answer

It wont turn on

press the reset button on the back

Nov 12, 2007 | Samsung YP-K3 MP3 Player

1 Answer

3red lights, wont turn on

well,this happened to me one time, so I unplugged the cosnole and waited 15 minutes.. make sure the remote has fresh batteries too.  If that doesnt work, call microsoft, i heard they increased the warranty on xbox 360. 1-(800) 4MY-XBOX (469-9269

Oct 26, 2007 | Microsoft Xbox 360 Console

1 Answer

Wont turn on 3redlight

Either look on and enter "X Box 360 - rings of light" and it will give you the answer to your problems, or call 1800-4my-xbox and they are a great help.

Oct 26, 2007 | Microsoft Xbox 360 Console

2 Answers

Sony SNC-P1

I think it is Guest for both OR try Sony SNC-P1 for both logon & password ... good luck.

Aug 08, 2007 | Sony SNC-P1 Network Camera

Not finding what you are looking for?
Sony PlayStation 2 (PS2) Console Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Video Game Consoles & Games Experts

Zhenya Ogorodnikov

Level 2 Expert

218 Answers

shaun taylor

Level 3 Expert

1527 Answers


Level 2 Expert

219 Answers

Are you a Sony Video Game Console and Game Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides