Question about Behringer Sx2442fx Eurodesk 24channel Mixer New

Open Question

Schematic I have that mixer , power supply is upset ,I want repair it, please help me

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fault on auto mixer


To direct you to a schematic we will need the make and model of the mixer.

May 01, 2016 | Music

1 Answer

I have Behringer xenyx 1622fx , It will turn on the power but a few minute the power will turn -off , Please help me to solve the problem of this unit in power supply section or other section.


Here is your schematic:

http://elektrotanya.com/behringer_xenyx_1622fx.pdf/download.html

Scroll down and find link "Get manual" and click to download.. IGNORE other download links they are for third party viewers. Power supply is on page 11. This is a switching power supply running from line voltage. For personal safety USE AN ISOLATION transformer when working on it. First thing is to measure all the voltage outputs before and during shutdown. Switching power supplies often require use of an oscilloscope to repair. The three terminal regulators that follow the main switching supply each have thermal shutdown so if one of them is being overloaded it will shutdown and that voltage will drop way down. Use great caution when working on the supply!!!

Jul 20, 2012 | Behringer Xenyx 1002fx Mixer 10 Input 2...

1 Answer

Behringer sx3242fx not working .i need circuit diagram .


Behringer will not release schematics unless you are an authorized service agent... however, sometimes you can make do with the few schematics floating around... What is the problem with the unit? They typically use a switching power supply and the schematics of those aree usually similar enough to repair them.

Sep 09, 2011 | Behringer Sx3242fx Eurodesk 32-channel...

1 Answer

My europower pmp 2000 powered mixer wont turn on and the fuse appears good. I turned it on and it immediately turned off ,nothing smells burnt. any ideas on what it could be


This is likely a power supply failure, possibly brought on by a failure of one of the amp channels.

This is probably close to your supply:

http://elektrotanya.com/behringer_sps600_power-supply_sch.pdf/download.html

Scroll down to "get manual" and click on that to download schematic. Ignore other download links.

Aug 05, 2011 | Behringer Pmp2000 Europower 800w 10ch...

1 Answer

My mixer stopped working out of the blue no power want turn on anything ??????????????


Power supply probably failed. This is not a DIY for the inexperienced.

This will be close to your schematic: http://elektrotanya.com/behringer_pmh1000.pdf/download.html

Scroll down to "get manual" and click to download. IGNORE other download links.

Jul 19, 2011 | Behringer Europower Pmp1000 Powered Mixer...

1 Answer

Hi all i own a behringer XENYX 802 audio mixer. this device is powered by a power supply that as input to the mixer gives 18,5 x2 Ac, 150ma. i would like to know in which point of the circuit i can...


You would need TWO DC supplies as they use AC so they can create both a plus and minus 15 volt power source to run the internal op amps.

Here is a schematic for the 1202 which has same power supply configuration as the 802.

http://elektrotanya.com/behringer_xenyx_1202.pdf/download.html

Scroll down to the little link "Get Manual" and download the service manual and schematic. You will find the power input in the upper left corner of page 5.

Mar 29, 2011 | Behringer Xenyx 802 8-input 2-bus Mixer W/...

2 Answers

Soundcraft EPM12, need power suply schematic pls.


This isn't your model BUT it is likely so similar as to be close enough to work a power supply problem.

http://elektrotanya.com/soundcraft_folio_f1-6-i-p_mixer.pdf/download.html

These companies don't change designs very much between different models.

Feb 07, 2011 | Soundcraft Epm12 Analog Mixer - Epm 12

1 Answer

Hello! I have a Behringer EUROPOWER PMH 1000. But the power board burnt source. What do I will acquire another, or fixable?


Often teh power supply fails because of other problems. Unless the board has flame damage the parts that are defective can be replaced... Getting some of the parts that are special can take time. Most of the components are available at many sources however. The SPS400 power supply can be repaired.

Here is link to schematic that should have the SPS400 as well as the rest of the PMH1000 on it.

http://elektrotanya.com/behringer_pmh1000.pdf/download.html

Jan 18, 2011 | Behringer XENYX 2442FX Mixer

1 Answer

Mixer not working and board getting hot


There is likely a voltage regulator or a diode burned out in the vicinity of the power supply. If you have the schematic, start at the power supply and work through the circuit to the I.C. Also look up the pinout on the internet for that I.C. With the power on test the voltages at each pin on the I.C. You should not have supply voltage readings on any of the signal pins. This is an indication that the I.C. is also burned out. Use a volt ohm meter with a D.C. voltage setting. Also hopefully your meter should have a diode test function. If not you can still test them with the resistance test function.Here is a link to an explanation:http://www.elexp.com/t_test.htm I hope this helps.

Mar 03, 2010 | Vestax Pmc 280 DJ Mixer

Not finding what you are looking for?
Behringer Sx2442fx Eurodesk 24channel Mixer New Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Behringer Music Experts

Michial Gueffroy

Level 3 Expert

1138 Answers

Vito Vacirca Jr.

Level 2 Expert

140 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Are you a Behringer Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...