Question about Toys

1 Answer

Replace belt on 397

How do i replace a belt on a lionel 397 coal loder

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Many toy train part suppliers have the replacement belt. It does require some dismantling to replace the belt. Tip wrap a layer of package tape where the belt runs not over the lower pulley but along the path of the belt, it helps prevent coal bits from jamming in there. Once you have replaced the belt and have reassembled the unit NEVER use anything other than Lionel 206 Coal or its latest incarnation. Other materials are either too heavy or too fine and will jam the mechanism.

Posted on Jun 19, 2014

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to an Expert (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 18 Answers

SOURCE: I have a complete Lionel Electronic Control train

Yes it can be fixed. Does the transmitter work? I am asking if other cars and the locomotive respond to the transmitter ECU-1. The dump car is a little different from the other cars as you need to hold the button down for several seconds to get it to dump momentatrily to uncouple. There is a thermostatic time delay as part of this car's receiver.<br /> Look it up in the old Lionel Service manual (original or Greenberg reprint) or the Greenberg operating guide (small thick hardbound book)<br /> <br /> Ed

Posted on Aug 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Lionel 7796 New York Central. The remote blinks a constant red and it does not operate the locomotive.I thought it was the remote so Lionel sent me a new remote but the same problem exists.


The locomotive is not receiving the single from the remote . You need to paire them. In the Manuel should be intuitions for pairing. Hope this is some help.
REDEAGLE

Dec 17, 2017 | Crafts & Hobbies

1 Answer

Need a #97 Lionel Coal Conveyor Parts List ?


What is wrong or missing on yours?

Nov 13, 2016 | Crafts & Hobbies

1 Answer

ON THE BACK WHERE THE ENGINNER WOUDL STAND ON A REAL TRAIN THERE IS TWO POSTS .WHAT ARE THOSE FOR


if by real you ,mean a steam engine , as on real modern trains they don't stand ,they sit and they arnt in the back either , anyways on Baldwin 700's (from memory?) there was two low posts with large round knobs on top near operators cabin , these were Hip posts for coal stoker to lean on to support themselves as engine moved along but still allowed them to use there arms to stoke coal freely

Dec 03, 2015 | Lionel Century Club 671 S2 Turbine Steam...

1 Answer

How to wire lionel 6-14107?


If you have the repro coaling station, the following pdf applies:
http://www.lionel.com/media/servicedocuments/5956714107250002.pdf

If you have the original coaling station, see page 25 of the following pdf.
http://www.slsprr.net/history/1954LionelTrainsAccess.pdf

Aug 21, 2014 | Crafts & Hobbies

1 Answer

Lionel o guage polar express set transformer has a bell button but don,t work no sound


IfIam correct, the basic Polar Express came with just a whistle. There is an optional coal tender that has a better sound system in it...Whistle bell and steam sound also try reversing the power wires at the transformer or track

Mar 11, 2014 | Lionel Trains The Polar Express O Gauge...

1 Answer

Purchased a Lionel New York Central Flyer Operating Freight Expansion Pack with a coal dumper. My set runs on O-gauge track, not fas track, but the magnet operation appears to be the same. The coal...


The magnet may not have enough punch using track power. Recommend you use an aux power source fixed 10 to 13VAC supply and not track power. There may also be a slight + difference between the track magnet head and the plate on the coal car so that there is insufficient force to release the dump mechanism.

Apr 22, 2011 | Lionel New York Central Flyer

1 Answer

I have a complete Lionel Electronic Control train but the automatic coal car does not work. Can it be repaired?


Yes it can be fixed. Does the transmitter work? I am asking if other cars and the locomotive respond to the transmitter ECU-1. The dump car is a little different from the other cars as you need to hold the button down for several seconds to get it to dump momentatrily to uncouple. There is a thermostatic time delay as part of this car's receiver.<br /> Look it up in the old Lionel Service manual (original or Greenberg reprint) or the Greenberg operating guide (small thick hardbound book)<br /> <br /> Ed

Jan 03, 2010 | Toys

2 Answers

I bought the set last year of holiday lionel trains g replaced batteries, have light on remote and noise from engine but no movement? any ideas


If all cars are not properly on the track, the engine does not have enough power to pull the cars. Try with engine and coal car only to zero in on cause.

Dec 23, 2009 | Lionel Trains Holiday Express G Gauge...

Not finding what you are looking for?
Toys Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toys Experts

kakima

Level 3 Expert

102366 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

17317 Answers

Are you a Toy Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...