Question about Husqvarna Garden

1 Answer

How much time does it take to manufacture a single chainsaw

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has written 7 tips or uploaded 3 video tips

  • Expert
  • 145 Answers

Check out "howitismade" TV show they did an episode on ECHO chainsaws

Posted on Apr 13, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Saw dies after working for fifteen minutes

Could be a multitude of issues, I however suspect the carb is in need of adjustment. The chainsaw while operating under manufacturer specs runs between 900 degrees (F) and 1100 degrees (F) if the chainsaw exceeds 1100 (which after 15 minutes of use this is possible) the chainsaw quits or what is called a lean seizure, the piston swells and scores the cylinder walls. when the piston swells too much it seizes the chainsaw, after it cools down it the piston will shrink and the chainsaw will run again. Too many times and the piston will score the cylinder causing damage and space between the cylinder wall and the piston.

Oct 10, 2016 | Garden

1 Answer

Is there a warranty on a second hand chainsaw.Ser.number4400936 966 61 10-00

Unlikely, but go to the manufacturer's website and look up their warranty policy. Even if warranty is not limited to original owner it will have some sort of time limit, so unless you possess the original receipt getting warranty work may be difficult.

I’m happy to help further over the phone at

May 13, 2016 | Garden

2 Answers

What is the gap between coil and magneto

I use a piece of A4 copy paper to set the gap.

Apr 05, 2015 | Garden

1 Answer

Fuel mix 1.40 or 1:50?

This is usually dependant on the two stroke oil quaility, good quaility two stroke oil from a major chainsaw manufacture will normally be advised to mix at 50.1, always try to buy good two stroke oil, from a chain saw manufacturer, they know the importence of oil quaility on high reving two strokes.

Aug 24, 2011 | Poulan Pro 42CC 2 Cycle Chainsaw, 18"

1 Answer

Trying to find out what year and model my 350 husqvarna chainsaw is numbers on saw are 967 01 18-00 03 4103750 can you help ?

I am faily certain 967 01 18-00 has to do with the EPA.

If 03 4103750 is the serial number then;
Enter the 3 digit model number (no XPs, Es, just the numbers)
Serial number decode – useful when downloading IPLs and Manuals
03 4103750
03 = year produced – 2003 (single digit before 2000; please contact Husqvarna for single digit clarification
41 = week produced – October (05-11)
03750 = 3750th unit Husky produced that week (not saw, unit)

If you have more questions or need additional help please reply below and I will get back to you. HTH & Good Luck.
Thank You for using FixYa.

May 25, 2010 | Husqvarna 350 18 Inch Gas Chainsaw 52CC...

2 Answers

How to find date of manufacture for Stihl chainsaw ???? # on handle sticker is not DOM--

The date of Manufacture is not posted on a Stihl chainsaw. Only a dealer can tell you that information, and Stihl doesn't like to let consumers know this information, as from a selling point of view, model year can't be used to negotiate a lower price (like last year's car model...still new, but you get a lower price because it's not the current year.) You may find a dealer that will look up the serial number and tell you, but not always is it possible.

Apr 22, 2010 | Garden

1 Answer

Wanted coil ignition module for Husqvarna 394xp chainsaw

I found an IPL for your saw here:
Enter 394 as model number (no XPs, Es, just the numbers)
Serial number decode – for use with IPL
06 1500198
06 = year produced – 2006 (single digit before 2000)
15 = week produced - March
00198 = 198th unit Husky produced that week

I chose the 92-10. The coil and wire were manufactured as separate pieces. I found both at Jacks Small engines. It is interesting that the same ignition wire fits a Poulan at 1/2 the cost. About $86 for both pieces at Jacks. HTH

Oct 19, 2009 | Husqvarna Chain Saw 20" Bar

1 Answer

I keep breaking the plastic piece on stihl ms 250

before pulling descompress that little valve on the piston head

Feb 02, 2009 | Makita DCS6401 20 20",64cc Chainsaw 2...

2 Answers

I have an old Remington gas powered chainsaw for which I am having a difficult time locating an owners manual. Does anyone have a notion who manufactured the chainsaws for Remington? If I knew who the...

chainsaws in car dept?? chain saw ??dont need them here in spain all trees cut down years ago to make paper for somebody to put a rubber stamp on and charge a fortune so they can sit on their backside and do nothing constructive towards the economy.i would guess its made in china like everything else nowdays .cant be that difficult to repair providing you can buy new parts or have some made in a local engineering works -----if any left where you live

Nov 29, 2008 | Ford F-350 Cars & Trucks

Not finding what you are looking for?
Garden Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Garden Experts

Jim Parker
Jim Parker

Level 3 Expert

1041 Answers

Phil Walker
Phil Walker

Level 3 Expert

608 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Husqvarna Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides