Question about Linksys Wireless-G WRT54G Router

Open Question

How to connect WN2500RP to WRT54GS

I bought a Netgear Bridge that I want to connect to my router WRT54G.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 19 Answers

SOURCE: wireless router connectivity WRT54GS

If you use cable connection, try power cycling the modem and router by turning off the modem and router and turning on the modem first and then the router. Though it is a very simple step it sloves most internet connection problems. If you are using DSL, check with your ISP if you are using PPPoE or just dynamic (it all depends on your modem). IF it is PPPoE, check to make sure your connection type is selected as PPPoE and put in your username and password from your ISP.

Posted on Jan 12, 2008

Ad
  • 52 Answers

SOURCE: how to bridge my motorola 2210 DSL modem & linksys wrt54g router

Try these insturctions. Jump to page 109. http://www.netopia.com/support/hardware/manuals/SoftwareUserGuideV751Clsc.pdf

Posted on Aug 29, 2009

kakee
  • 1269 Answers

SOURCE: I have a netgear ds116 hub and i want to set up a linksys router

Here's what you can do. Don't connect the Linksys router yet to the hub. Connect 1 computer directly to the Linksys router. Access the router's setup page of the Linksys router thru http://192.168.1.1

It will prompt you for username and password. No username and password is admin.

Look for Local IP Address or LAN IP Address. Change the LAN or Local IP Address of the Linksys router to 192.168.5.1 then click on Save Settings at the bottom. Right after saving the settings, unplug the power of the Linksys router, connect it to the hub and it should be good to go.

Posted on Oct 06, 2009

govinda123
  • 2260 Answers

SOURCE: BRIDGING MODEM AND ROUTER

If you connect the computer directly to the modem, does it work?
If that works then the modem is working.
Now connect the computer to the router and the modem to the router.
You will need to open the set up page of the router to check the settings of the router.
You can set up the router without the CD also.
It is very easy.
Click Here for step by step instructions about how to set up the router

Click Here for more info

Posted on Dec 06, 2009

  • 62 Answers

SOURCE: How to cennecting Aztech modem DSL600E with Router linksys WRT54G

First!
Do you have a connection in your modem?
if you do, you need to set up the linksys router in DHCP internet set up.
To have access to the linksys you need to go to:
http://192.168.1.1
The password it's admin
and the username in blank (no password)
change the internet setup to DHCP

Make sure you don't have the Same address for 192.168.1.1 or you modem cause if you do you'll need to change the ip address on the linksys router...
:)

Posted on Apr 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Locate WPS button on FWAG114


Thanks for posting to Fixya!

According to the manual I found at the following link;
http://downloadcenter.netgear.com/en/product/FWAG114

www.youtube.com/watch?v=8ffqvIoxcOc

WPS is not supported on this router. However, my suggestion would be to reset the WN2500 to default with the reset and start fresh, using the manual setup. You can find the help you need here;

http://kb.netgear.com/app/answers/detail/a_id/19887

NETGEAR Support Answer WN2500RP FAQ


I hope this helps you with your setup!

Oct 05, 2014 | NetGear Computers & Internet

1 Answer

Netgear extender install wn2500rp


Configure the extender as a bridge.

Feb 21, 2014 | NetGear WNR2000 Wireless Router

1 Answer

Mywifiext net welcome


You can't connect the range extender to the wireless router or you can't connect your wireless devices to the range extender?

If its the router what is the name and model of the router?

Nov 19, 2013 | Computers & Internet

1 Answer

I can not gem=t my WN2500RP to connect to my Netgear Router


To properly set up the WN3000RP you first have to push the WPS or Push 'N' Connect button on the router-WN2500RP(on the back of the router between the reset and the wired connection slots) and then the Push 'N' Connect button on the extender. It should negotiate and establish a connection between them.

Sep 28, 2013 | HP Netgear Wn3000rp Ieee 802.11n - Draft...

1 Answer

I want to use my Linksys WRT54G as a bridge going thru Verizon FIOS 9100EM. What settings needs to be changed on the 9100?


You really don't need to change anything on the 9100 but with the router yes. And setting up the Linksys router depends on how the 9100 was configured. Just let me know if you still need more help.

Dec 22, 2010 | Linksys Wireless-G WRT54GS Router...

1 Answer

I just bought a laptop with Windows 7. I have a


hi,

for you to be able to configure the modem to the router,you will need to set the modem to bridge mode first for you to be able to give way for the router,try to contact verizon and let them bridge the modem then right after that,thats the time you will configure the router

thanks and God Bless

Jun 26, 2010 | Linksys Wireless-G WRT54G Router

1 Answer

So I have a little problem. I'm trying to find out how to connect 2 wireless routers together from across the house. The internet side is connected to a Linksys wireless router (WRT54G). This is located in...


you need a wireless ethernet bridge(like wet54g/wet610n) which will grab signals wirelessly from u're primary router wrt54g,& then a ethernet cable from wireless bridge will be connected to one of the lan port of u'rs netgear router(otherwise u will not be able to do file & printer sharing between 2 routers)Remember,the ip address of all 3 devices shold be of same class.

Jan 02, 2010 | NetGear WGT624 Wireless Router

1 Answer

What is the best wireless router for comcast internet ?


Linksys WRT54G or Linksys WRT54GS.
Both are working fine with comcast.

Aug 01, 2009 | NetGear WGT624 Wireless Router

1 Answer

DSL line disconnects on WRT54GS only


Try to change the LAN IP address of your router to 192.168.2.1 by accessing the router's Setup page. You also need to set your Westell modem to "full-bridge mode". You need to ask assistance from your ISP to bridge the modem. After that, set-up the Linksys router to PPPoE then power cycle it.

Apr 15, 2009 | Linksys Wireless-G WRT54G Router

2 Answers

Linksys WRT54GS


No, you should however, log into your Linksys's admin page and copy your settings down. Put those back into your Netgear and you should be good to go.

Feb 15, 2009 | Linksys Wireless-G WRT54GS Router...

Not finding what you are looking for?
Linksys Wireless-G WRT54G Router Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Michael Galve
Michael Galve

Level 3 Expert

1269 Answers

Are you a Linksys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...