Question about Hobart HL600 Legacy Stand Mixer

1 Answer

Switch reluctance drive fault

There is fault drive unit one of resister was open .some one provide me its diagram of switch reluctance drive and can solve my problem

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 109 Answers

There are no schematics for the reluctance drive unit to get details of every resistor, at a technician level. Perhaps try resourcing the company that makes the drives for Hobart. The troubleshooting of the drive is complex and dangerous because of residual high DC voltages. Use extreme caution while near the drive. Voltages take a while to dissipate.

Posted on Mar 23, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is a good source for a reasonably priced 200-240V 2.7 HP switched reluctance motor found on Hobart's HL600 mixers?


Baldor no longer manufactures that motor. Hobart would have to install a kit that includes every electrical component in the machine. Be careful if you find a used one, they have a very fragile encoder on the rear of the motor.

Aug 19, 2015 | Hobart Food Mixers

1 Answer

Vision 708 mixer amp


Jimbo

I am not sure about the LED fault lights....but I have a few troubleshooting angles to provide a start:

Try checking the power supply at the output devices and compare with the good (Left) channel.

The distortion you are hearing may be due to
low voltage.

This is a stereo amp, so you have a good (Left) channel to compare with. Use a multimeter to compare resistances (no power applied) or voltages (power on) at the components working back from the outputs of each channel. When you find a difference you have located the faulty area.
If you can get an oscilloscope it can also be used to trace the path back from the output of each amp. Good Luck Be careful!

Jan 08, 2008 | Food Mixers

1 Answer

KitchenAid Mixer struggling to spin?


Check everything you have done for a mistake, the pin through the planetary, the pin through the fuse gear and the pin in the main shaft that drives the bevel gear. That's the gear that pinion gear on the fuse gear shaft mates with. After that you are left with a fuse gear fault. I am assuming that the motor is turning at normal speeds and not somehow binding up, no reason why it should as motor stays in one piece during gear changing procedure.

Apr 18, 2014 | KitchenAid Food Mixers

1 Answer

How to pull auger drive shaft for Hobart 4346 mixer-grinder?


The oil seal is the resistance you feel. take a soft mallet or hammer with a soft drift and gently but firmly tap the stub shaft and it will drive out the oil seal in the hopper direction.The lower skirt of the tapered bearing is what contacts the seal so go slow.
Worked for me.

Jan 23, 2013 | Hobart 4346 Meat Grinder Mixer Chopper...

1 Answer

Whats does b_9d mean. My mixer wont start to mix. The power is good but it tels me b_9d.


that fault is a b_gd.there are 10 things that can cause this.1.start sw.momentary contacts not closing. 2.stop sw. contacts open. 3.bowl guard sw. open or malfunction(b_gd)displayed on timer.4.contactor 1con malfunction.5.timerboard malfunction.6.wiring incorrect from sr drive to motor or 1con.7.sr drive malfunction 8.1 con monitor from control drive disconnected from contactor coil9.encoder malfunction 10.motor malfunction. hopefully just your bowl guard switch is no good. hope this helps, dont forget to vote, monomoy

Feb 01, 2010 | Hobart HL600 Legacy Stand Mixer

1 Answer

Kitchenaid pro stand mixer will not turn on I has been sitting for 3 months without being used. It is a 475 watt bowl lift 6 qt mixer. about 3 years old.


How comfortable are you with electrical parts? With the mixer UNPLUGGED and the switch ON measure resistance between the (flat) plug pins. If it's infinite (no meter movement) which is to be expected, there is an open circuit. The switch could be open or the wire to the switch could be disconnected (improbable) or the motor could be burned out and open (not very probable).

Maybe you could take the switch to a shop and have it tested.

This is not really a solution, just step 1.

Feb 27, 2009 | KitchenAid K45SS Classic Stand Mixer

1 Answer

On/off switch


if the mixer is pretty old then the timer is bad.If its a newer unit the timer or the bowl height sensor is bad.

Jul 01, 2008 | Hobart A200 Stand Mixer

4 Answers

NEED A WIRING DIAGRAM FOR A A200 HOBART MIXER


I had a look on google and came up with a service manual. not sure if this has the wiring diagram but the only other thing i can suggest is to contact te manufacturer direct. Go to http://cgi.ebay.com/HOBART-A200-20-QUART-MIXER-SERVICE-PARTS-MANUAL_W0QQitemZ160203114233QQcmdZViewItem
hope this helps.

Feb 02, 2008 | Hobart A200 Stand Mixer

2 Answers

LOOSE SELECTOR DIAL


SInce there are no fasteners looks like the dial has lost its "grip" . Will come off if you force it . You can fix back replacement or the same one with some skilful application of araldite or a similar epoxy resin

Mar 13, 2007 | Sunbeam 2366 MixMaster Series Hand/Stand...

Not finding what you are looking for?
Hobart HL600 Legacy Stand Mixer Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Food Mixers Experts

Ross Keen

Level 3 Expert

1237 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

1803 Answers

Are you a Hobart Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...