Question about Jado 842/701/105 Hatteras Single Lever Monoblock Vessel Faucet with .5" Val

1 Answer

I cant get handle off my hot water monobloc tap after taking screw out

I took top off then star screw but handle wont come off what can i do to fix it i think if i prise it off with a flat screwdriver it will damage it

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.


    An expert who has answered 20 questions.

  • Expert
  • 169 Answers

I am providing the link of the installation instruction for your reference. It seems that there is a lock nut underneath to hold the faucet (figure 1, part 6).

Posted on Feb 21, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i put the o rings and springs in my old leaking 2 handle faucet

Make sure the water to the tap set is turned off. Remove the hot plug button, use a small knife to pry it out of the top of handle. Remove the screw inside the handle that holds the handle to the cartridge. Use an adjustable wrench to unscrew the tap handle from the base. Once removed, separate the cartridge from the shell (the unscrew from each other). Use the appropriate size and type of screw driver to remove the screw holding in the flat washer. Using a small dull needle or flat screwdriver remove the "O" ring from the valve stem Replace the o ring by just slipping it on. Make sure you clean all areas of the stem and the stem cartridge of old grease and dirt etc. Use new clean valve stem grease on the O ring before re installing into the cartridge. Insert the new washer onto bottom of valve stem, Screw on. While you have it apart look down inside the tap to inspect the valve seat. If its chipped, broken, rusted etc you MUST replace it, if you do not any new parts will sot stop the leak. Valve seat MUST be nice and flat and clean. To remove the seats most taps will require a 3/8" Allan wrench. Push the wrench into the slot of the seat, turn C-Cw to remove, CW to replace. These parts are cheap. If you need to replace the seat, take it with you to H Depot so they can give you the correct one. NOTE: Its best to do the cold at the same time, saves you the trouble of doing it again later. Same applies to the cartridges. You can replace the entire cartridge instead of rebuilding them at only a few bucks each, its much faster and easier.

Aug 10, 2014 | American Standard Plumbing


No Steam, No Water? Quick Fix

All of a sudden I had no steam and no water.

I could hear the pump chugging and trying hard, but nothing came out of the nozzle.

First, check to see if the nozzle is blocked. If it's not, try turning on the tap (faucet) and PUSH IT IN towards the machine.

If you now get steam and water, there is a quick fix.

Switch off the mains, unplug the coffee machine and take all normal precautions not to electrocute yourself.

There is a small cam on the (Part 9161205 - Faucet rod stem) which pulls the tap IN as it is opened and OUT as it is closed.

1] Remove the coffee container - there are two phillips screws only, and it lifts off.

2] Remove the top casing. There are two phillips screws either side at the front top, hidden by the door, one star head screw under the water tank, and one normal phillips screw under the water tank in a deep channel.

3] Take a look at the small cam on (Part 9161205 - Faucet rod stem) and see if it moves in and out as you turn the water/steam tap on and off. If it doesn't the plastic has sheared off. If it does move in and out - this is not the fix for you!

4] If it does NOT move in and out as you turn the water/steam tap on and off, find a small self-tapping screw and screw through the angled cam hole into the faucet rod stem. Pop the top casing and the coffee container back on and your machine is now fixed!

Now for a delicious cappuccino62e2053.gif!

on Jun 18, 2008 | Saeco Vienna De Luxe Espresso Machine

1 Answer

Simpson eziset 605 wont take in hot water

Hot valve in washing machine required. Part is between $25 & $60 STEP 1: unplug machine STEP 2: undo the 3 Phillips screws on top of machine the fold top console forward STEP 3: Undo hot tap,disconnect 2 wires running to hot valve,remove valve,fit new valve. STEP 4: Refit top console. DONE

Jun 17, 2012 | Washing Machines

1 Answer

Cannot get the hot water handle off. Have remove the collar and the base, handle will still not come off

im not 100%sure on the particular set of taps you have ,but by looking at the picture on screen ill hazard a the way im a plumber .under the lever for hot water tap is a cone shaped shrowd .narrowest at its point where its in contact with lever and broadest at bath top end .this shroud will screw off .in the middle of the lever you pop off insert and unscrew cross head screw and then back off shroud ,the tap spindle should then be exposed

Jan 19, 2011 | Grohe 25.506.EN0 Geneva Roman Tub Filler...

1 Answer

How do you remove the hot and cold taps on a shannon monobloc mixer tap, water is dripping from the cold tap

Use 2 Adjustable Wrenches . you may need a Allen key set to Remove the Mixer unit . You can fix the Water dripping problem may be replacing a O ring

Nov 18, 2010 | Plumbing

1 Answer

Leeking from top when on

if we are talking about a faucet then your problem is call the packing nut. sometimes the packing nut cracks or after so many time the faucet been open it just gets wear so what i recommend you to do is turn water off down under the sink and take a screw driver to remove handle, then with a pair of chanalocks remove trim and stem note: make sure stem is in on positiion if not in on position the treats on the faucet may cross treat and then you will have to replace the faucet so dont forget before you star taking it apart turn it off and star removing everything on the top, i will just replace the stem and you problem will be fix. but if you want to try a cheaper solution that may work just remove the handle and the trim and with the chanalocks adjust the packing nut that will be the nut on top of the stem right below the handle and tested.

Oct 03, 2009 | Halex Liquid Tight 90 Degree Elbow, 3/4"

1 Answer

WF840 is flashing H20 what is the problem

machine cant take in water, if you hear a quiet hum when a programme is started that will be the inlet valve opening, check the inlet hose isnt kinked, the water tap is on, on the isolator tap sometimes the little handles snap and you cant turn it on or off, remove the handle (littlwe screw on top) and turn it with a small spanner

Jun 09, 2009 | Hotpoint Ultima WF840 Front Load Washer /...

2 Answers

Shower handle leak

turn off main water in home . turn on tap some where in home to release presser take shower handle off (screw under cap) unscrew the tap with a wrench unscrew on insides you pull out replace washer put all back togethere

Feb 11, 2009 | American Standard 3275.505.099 Colony Soft...

1 Answer

Leaking Kitchen Tap

I am assuming that your kitchen tap is leaking through the spout

if it is single lever you will need to remove the crown and spout by removing a small erasure size cap on the housing right under the spout or up near the back of the ever then use a hex wrench to remove the set screw( plug the drain holes do it does not go down the drain)

turn the water off (hot and cold ) under the sink
remove the set screw and lift off the lever

at his point you can take an adjustible wrench(channel lock and tighten the big ring nut that holds the cartridge in place

temorairly put the handle back on and put the handle in the off position turn the water on under the sink and see if it stopped leaking

if it still leaks you have to turn the water back off and remove the lock nut then the cartridge and go to big box store with old cartridge and name of mfg and get a new one and install

If you have seperate hot and cold valves on top of sink deermne which is leaking by turning one off with oher on undr the sink

once you have determined which it is (hot or cold)
take a phillips head screw driver( remove plastic clear cap on top of faucet handle with sharp crewdriver of knife blade) and remove the screw holdin the handle on to the stem(turn counter clock wise

be sure to turn water of under snk on both faucet risers after removing acrylic handle you then take an adjustible wrench and remove the crown nut turn counter clockwise until it comes off over stem

remove stem( looks like size of a pretzel about six inches long with washers on side and one on end

take the stem to local hardware(ace) or big box store and go to lumbing section ask clerk to inspect and recommend replacement washers or replacement stem (if needed)

go back reinstall and tighten crown nut snug( open (turn counter clockwise) tem valve before you snug it down with crown nut
install acrykic or chrome handle with brass phillips screw then ut cap on and turn on water and check for leaks

good luck

Dec 30, 2008 | Home

Not finding what you are looking for?
Jado 842/701/105 Hatteras Single Lever Monoblock Vessel Faucet with .5" Val Logo

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jado Plumbing Experts


Level 1 Expert

11 Answers


Level 1 Expert

33 Answers

Brad Brown

Level 3 Expert

17328 Answers

Are you a Jado Plumbing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides