Question about Hilti 120-Volt SDS Max Demolition Hammer TE 500-AVR Performance Package 3484551

1 Answer

I have a te 500 it not knocking at full strength

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Hilti Master
  • 1,774 Answers

A Broken front ring which blocks the lock bolt ?

Is there enough lubrication flow if something is broken inside replace ALLWAYS a complete servicekit , because its , beware of the Turmopol oil is expensive. there are equivalent oils if you asked special for it also by Hilti to buy.
Hilti and Duss are not the 2 cheapest brands of powertools.
Special Tolerance-free bearings are used it is all super calculated on a number of operating hours and about if something is defective, a complete overhaul is necessary.
These hammers may leak no trace of oil in the front until 2006 HILTI has in my Country support , but after this date
exclusively support to the end-users and support closed for brokering.

Posted on Apr 17, 2016

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need a control module for a hilti te.70.120v. If you have one or know someone who has l, please let me know.

No parts here and no connections other than a Google search which I assume you have already done.

Sep 28, 2016 | Hilti 120-Volt SDS Max Demolition Hammer...

1 Answer

My router says it has a full signal strength but it cuts in and out and states limited signal strength when there is full signal strength? is there something i've done wrong or a softwear issue ?

Sounds like there is an issue with the firmware. Or an internal issue with the device itself, Try a firmware update within the settings page. If the problem persists look into replacing.

Aug 22, 2010 | D-Link DIR-615 Wireless Router

1 Answer

Few problems wid Bajaj Avenger 200 dts-i

change repair shop for one. the knocking might come from bad gas, fuel up with supreme at reputable gas station. your dynamo/alternator/voltage regulator is probably not working properly either. check voltage

Jul 04, 2010 | 2005 Bajaj Bajaj Avenger

1 Answer

Casio atomic watch only has intermittent receive indicator

The receive indicator tells you the strength of the signal when the timing signal was transmitted, (this occurs only during the night).

The strength of the signal dictates how much of the indicator is shown i.e. full strength, full picture, half strength, half picture, no picture, no signal.

Signal strength seems to vary with location (how far you are from the transmitter), so perhaps you are in a poor reception area.

Feb 26, 2010 | Tissot Diver Seastar 1000 T19.1.593.51...

1 Answer

Kenmore Coldspot 69182990 - knocking noise

check te rubber mounts at the bottom of the compressor
the rubber rots after some time and the compressor moves on shutting down as the knocking could be that noise

May 20, 2017 | Kenmore Refrigerators

2 Answers

Wire off around door

Nexxt 500 WFMC3301 Front Load Washer
This video will show you how to change a door seal on this Bosch front loader washing machine and the best way to get wier back on te door.
we have al bosch repairs in our channel

Please remember to subscribe to our YouTube channel for all appliance tutorials

a 4 THUMBS rating is appreciated for answering your FREE question.

May 13, 2009 | Bosch Nexxt 500 WFMC3301 Front Load Washer

1 Answer

Poor signal strength

have a go at changing the wireless channel within your router there may be some interfearence generated by your pc that is affecting its signal strength

Oct 29, 2007 | Computers & Internet

Not finding what you are looking for?
Hilti 120-Volt SDS Max Demolition Hammer TE 500-AVR Performance Package 3484551 Logo

Related Topics:

315 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hilti Hammering Experts


Level 3 Expert

75005 Answers

Todd Arndt
Todd Arndt

Level 3 Expert

2044 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

1774 Answers

Are you a Hilti Hammering Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides