Question about Televison & Video

Open Question

Lg 42pq6000 won't switch on clicking noise comes from the back of the tv then stops and then nothing can any one tell me how to fix this

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jmgldsmth
  • 1869 Answers

SOURCE: tv not comeing on

your power relay is bad

Posted on May 20, 2009

SOURCE: LG 42 inch Plasma TV stopped coming on. Now

With this symptom, it is impossible to tell what the exact "Cause" of this symptom is. The LED's do not tell us what is wrong, sometimes it may indicate the "Area" in your case it is the X board. BUT thats NOT where the "Fault is" thats just the part that is affected. These days unlike the "Old" analogue days it just isn't realistically possible to fix anything but the most basic of problems with todays sophisticated units. This is quite apart from the Safety aspect, any unit that can cause a firs or have an explosion, or both, is NOT to be treated lightly, and and the repairer, of the unit is legally responsible, another thing to think about. Also, one must have tools, a Multimeter, a soldering iron, a deslodering iron, an oscilloscope, a signal tracer, tools, and most important of all, a Service Manual, without which, there is no way to even begin to understand and fix it, and more importantly Program it, AFTER it has been fixed. As these days a TV, is a PC, a Tuner, and an HDTV Monitor, and more, all in one. in the "old" days TV"s were more, rudimentary, and built to last for 20 years, and a "Parts" supply was set aside. They usually used to fail for only a few reasons, and they while still difficult, were less difficult to repair. Electrical knowledge was transferable, and they could be and would respond to, This-is-the-symptom-This-us-the-Fix, But that no longer applies, as now, it can be a Fault on I squared Bus, or "Sensor" failure, or it simple may have "Crashed" just like a PC, It could be a Diode go bad, and that will stop the whole thing. You see, in the day, the sets were Very "Fault Tolerant" because they were Analouge, and a faulty, component, or more sometimes, the set would always diplay something usually, and when they didn't it was one of anly a few things, sure there are always the horrid ones, and there are pleanty of those, but all in all it was quite easy. But with Digital Electronics, it either goes, or it doesnt, there are usualy few half measures. I mean thats the definition of logic either going or not. So it can take very little to completely paralyse a set, and generally give the only sysmptom, it can, by not working, usually No picture, or the like. So you, see the list is endless almost for any given SYMPTOM, as that is what is being seen, not the cause, as I keep going on about. Also any fault, usually involves the Power Supply, it is either the cause, the cause of the damage, or it is damaged. or ALL of them. Then after you have done the electronic repairs, you then must program the set to work, and align, and set up in general, any one of those settings missed or done wrong, back to square one. So, it is nearly always my professional opinion that one should always get a "Quote" form the manufacturers recommended service center, I cannot stress how important that last point is. It is even worth the cost of shipping. you see an authorised service agent, will have trained staff, trained on their brand, also they have first hand access to parts, original parts. This will actually save you money and ensure you can actually get it back fixed. Of course asking for a "Quote" also gives on the option of repair or replace. Often my clients,do not go through with repair, unless it is moderate, but in some of the more costly jobs they see it, as do i, that a replacement, with a warranty, is a better option. As an aside here, one could then tear the TV down, and sell the Known Good bits. You'd be surprised who needs parts, i myself often must by from third party sources to effect a repair. So money could be recouped, somewhat,and help out someone else.

Posted on Apr 08, 2010

  • 30 Answers

SOURCE: WHEN I TURNED ON TV LG MODEL 32FS4D-TE . I HEARING

the internal power supply is not starting up and needs to be replaced

Posted on Nov 28, 2010

  • 64 Answers

SOURCE: have an LG 42" Plasma model 42PQ6000 About 18

problem video connector inside the tv , you have to clean it properly
if you dont have good idea about electronic you need a
technicien

Posted on Jan 07, 2011

gopakumarg43
  • 73635 Answers

SOURCE: lg 50PG20 IS MAKING A CLICKING NOISE AND WONT COME ON

Hello
Check the power supply regulator board for the fault.

Posted on Mar 03, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lg 42pq6000


These blinks [flashes] are fault indication (Error Codes).From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit stage inside it.This will make repair easy.These are called blinking codes. Make sure about the exact number of blinking of the standby/power led, by switching On & OFF the set, for at least two times.Count it carefully.If you wish to get some details, check the site linked here.It has details about blinking codes, and fault locating, to many popular brand TVs and other devices.Viewing it in "Mosaic" will make surf easy.
http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given.

Feb 12, 2014 | Televison & Video

1 Answer

Dryer won't start..light clicking noises


There is a switch inside the unit that stops it when the belt breaks or comes loose. Check that.

Mar 15, 2017 | LG Home Applaince LG DLE2101W 7.3 Cu. Ft....

1 Answer

Lg plasma not turning on


sounds like caps however if making clicking noise check the relay on power board

Nov 25, 2012 | LG Televison & Video

1 Answer

Crackle Then Stop


Check the firmware on the tv. I would imagine youre connected with hdmi, and some tv's (lg, vizio mainly) have had firmware issues. check teh lg website for updates.

Jul 01, 2012 | LG 32LG30 32 in. LCD HDTV

1 Answer

LG DLP Suspected Faulty Bulb... how to be sure?


First pull back off turn TV on watch Fan behind lamp more then likely it is going bad Fixed LG 9months ago and it was the Fan.If Fan Stops turning Lamp will not light.

Aug 06, 2009 | LG Televison & Video

1 Answer

Tv shuts off tv/video doesnt work


that is a indication that a fault is about to occur, dont force that tv take it to a technician before it switches off completely, a power supply is supposed to be checked.

Mar 26, 2009 | Panasonic CT-36SL13 32" TV

1 Answer

LG 37LP1D - Buzzing niose coming from TV


I blew condensed air through the ventilation holes in the back of the TV, which greatly reduced the buzzing noise.

Mar 03, 2009 | LG 32LX1D 32 in. LCD Television

2 Answers

LG TV Making Bad Noise


have u tryed new cables for sound 1st

Feb 03, 2008 | LG 42LC7D-UB Television

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

73635 Answers

Cindy Wells

Level 3 Expert

5056 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...