Question about VIPER 7141V VIPER 4BUTTON REMOTE 7141V

Open Question

Both my viper remotes dont work

Just bought this used bell service truck and it has a viper system. i have 2 remotes, when i press any button the light on the remote lights but nothing happens? Help, i noticed there is a push button underneath my console

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 899 Answers

SOURCE: got a new remote for my viper 791XZ and reprogrammed it .

this usually means that the remote did not recieve a signal back from the module or the module did not recieve the remote signal
have you tried repeatively to press the unlock button? does the remote starter work or aux( trunk ) ?
also when putting the battery in the remote , be easy because there is a connector plug soldered on the board real close to where the battery is , and if it is hit by the battery hard enough it will cause those solder connections to disconnect and you will get the beeps and or other malfunctions

Posted on Feb 03, 2009

Megaduty
  • 1 Answer

SOURCE: VIPER 5701 remote how tofix?

you have the key pad lock turned on. It protects the keys from unwanted pressing when in your pocket. To unlock you hit the F key then the unlock key, you can now use any command untill you let it set for 60 seconds, then it locks again.

to stop this totally, u hold down the F key for 12 seconds it will beep and top light turns orange, then hold down the unlock key for 2 seconds, it beeps then u hit the lock key to turn off this feature (top green light goes out). then hold F down, and F down again, should b good to go!

REM

Posted on Jul 14, 2009

  • 69 Answers

SOURCE: back lighting for my viper 479v remote

you have to go in to the proramming mode of the remote to change this feature. you can access this by holding all 4 buttons on the remote at the same time. (or if you have the P button on the back you can hold it down by itself) you will hear 2 long beeps confirming the programming mode. at this time, you can change the settings by pressing 1 of the 4 buttons., each button will change a different function.

in no order------
1. Beep/vibrate or both
2. page or not to page
3.back light
4. hood, truck, or both

the remote will give 2 long beeps when it exits the programming

Posted on Aug 20, 2009

  • 1 Answer

SOURCE: My Viper 791xv remote isn't receiving the page

My battery ran low and I jump started my car which some how caused the problem. My viper technician made me a buy new remote but the problem continued even with the new remote.
Try disconnecting the battery of your car for ten minutes and then reconnecting it. It worked for me. Now i have a extra remote which i don't need.

Posted on Jan 19, 2010

  • 132 Answers

SOURCE: how to program viper 5701 remote

Unlock doors
Push and hold f button for 8-10 seconds until amber light is on solid
Push Remote start button for about 4 seconds till amber light flashes 3 times
Put key in to IGN position
Push valet (black button) one time and release
Push and hold valet button
Push either lock or unlock on viper remote
Key out of IGN
Test unit
The horn or siren may sound afterwards to indicate SUCCESS!!!!!!

Posted on Apr 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a viper 5900 car alarm with the 7701 vpx remote and the lock and unlock are reversed. How do I fix this


according to Viper tech support (I emailed them your question):

Thank you for contacting Directed support!

You may need to reprogram the remote to your phone. Please use the following instructions to reprogram the remote:

To program the remote to your system please do the following:

1) open the driver door
2) turn the key to the "on" or "run" position
3) locate the valet switch (small black button under driver side of dash) and press once, release, then press again and hold
4) after the siren chirps one time press the lock button on the remote
5) the alarm will give you a unique confirmation tone
6) turn the key off (the same unique tone will be heard again)
Warm regards,

Nigel McGee I Customer Service Rep.
Viper Support

Apr 28, 2016 | Viper Vehicle Parts & Accessories

1 Answer

Why won't it start vehicle?


[PDF]Responder LE Model 5701 Security and Remote Start ...

xtremetruck.net/file/1101-Viper+5701+Owner's+Guide.pdf
the year, make and model of the vehicle; vehicle license number and vehicleidentification number. All ..... One five-button/2-way Supercode Responder LE RemoteControl. ? .... Disarm. Unlock LED blink for one second with 2 Beeps. Remote. Start..... Long-time Viper system users will notice the following differences:.

Viper LED 2-Way Security + Remote Start System

https://www.viper.com/car/securityremotestart/.../viper-led-2-way-securit...
Viper's elegant new Responder LE transceivers mark a giant leap forward in 21st century vehicle security and remote start, and an evolutionary milestone for the ...

Viper 5901 remote start error fix - YouTube

? 2:38
https://www.youtube.com/watch?v=wsSorAf88nw
Jan 13, 2013 - Uploaded by Power2ThePeopleZ
5901 won't start vehicle; gives an error. ... or even try to open the hood. the door remains locked when you start the car with theviper alarm.

Help With Programming/Pairing Viper Remote - YouTube

? 2:49
https://www.youtube.com/watch?v=cgbQsZuVyt8
Dec 2, 2010 - Uploaded by Paul L
I have a two-way remote from my Viper 5901 system. ... The other car (one in video) has the Viper 5701 system in it. .... and then release 3) press the remote start button 2 times until pairremote is displayed 4)press and old ... I had the same problem that the remote won't pair with the system no matter what.

15964701 Viper 5701 2 way alarm w/ remote start won't




Jan 05, 2016 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

How do I reprogram a viper 5101 remote starer


on remote press the middle button for 15 sec. after three flashes on remote, put key in ignition and turn ignition on but dont start it. press button on antenna, release and then hold until horn honks or led flashes on antenna. lastly press lock within 5 sec

Jul 30, 2014 | 5101 LE 1 Way Car Remote Starter System

1 Answer

I got the valet mode to turn off but now my keypad dont communicate with my truck tried to reprogram it and it wont work


does the remote control the truck at all? if not try re-syncing it using the control button located on the antenna, read the manual about syncing it first

Nov 09, 2012 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

My viper alarm rpn 479v p x is not working. When i press the unlock or lock button it doesnt work it just beeps. The remote is also flashing rx. Whats wrong?


I got the Problem that my pager-function doen't work. I try it like the Manual saying (*-Button) but the two ways that gives doesn't work.

- Start the Programmmode while Pressing "P" on the Backside.
- Press the "STAR-Button or Panic-Button (Orange Key) on the Sender"
it Beeps 2 Times. (i try it again with 1 beep as reponse again)
i Wait 5 Seconds
it beeps 2 long times

i try the Responder, Activate the System, disarm the System. But the Pager don't change the state or receive any Signal.
The Transmitter is working perfect! No Problems to control the Viper 690XV.

What i do wrong?

Is there any hidden Feature or needable Programming in the Viper 690XV-Brain?

Thanks alot for any helpful Answer :)

May 02, 2012 | Directed Electronics 479V Remote Gen 2...

1 Answer

I bought a 2007 Camry with a remote start. The seller doesn't know how to start the car with the remote. The remote is a 4 button Viper 474V.


First, be sure that the remote is programmed for the vehicle by using it to operate the door locks(pressing the lock and unlock buttons). The parking lights should flash if nothing else works.The usual way to operate the remote starter with this remote is by pressing the * button once but, the option could have changed if the remote has been reprogrammed differently. So, try pressing the * button once. If this doesn't work press it twice within two seconds.If this doesn't work try pressing the lock and unlock buttons at the same time. If these steps fail to initiate the remote starter try the steps listed for the * button with the aux button. If either of the remote starter inhibits (hood pin, neutral safety) are active you should receive flashing parking lights for a failed attempt to remote start.

Jan 16, 2011 | Remote Start System

1 Answer

Just bought a`used truck that came with a Viper RPN 479VPC remote. Is this just a car alarm or is this a remote start also? Any help? Little blue remote with car diagram on screen...has lock, unlock, aux,...


That remote can work with both a security system, and a combo unit security/starter.

Best bet is to take the vehicle and remote to your local Viper dealer and they can look the car over and tell you what was installed and help you learn how to use it.

Jan 16, 2011 | Directed Electronics 479V Remote Gen 2...

1 Answer

My remote starter for my viper 5900 2 way trans isnt working...my battery went dead in the remote, than after i replaced it, it's not working properly


Try reprogramming the remote. Open the door, turn ignition on, press and release valet switch one time, then press and hold valet switch while pressing lock button on remote.You should hear a confirmation chirp from the alarm. Release both buttons.Turn off ignition. test.

Oct 03, 2010 | 5900 SST 2-Way Security System / Remote...

1 Answer

I bought the car with wiper alarm system and remote start. it wont start the vehicle, could it be because of low battery, the alarm its self works fine, arm and disarm


it may need to be programmed.......

-press the "f" button and hols for 12 seconds (ignore the beep at like 4 seconds.)
-press and hold the unlock button for 2 seconds...the remote should beep two times. each feature that is active will have an led light beside it. press the button to activate the feature. if the light is on the feature is on...

hope it helps...

Jan 06, 2010 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

2 Answers

Back lighting for my viper 479v remote


you have to go in to the proramming mode of the remote to change this feature. you can access this by holding all 4 buttons on the remote at the same time. (or if you have the P button on the back you can hold it down by itself) you will hear 2 long beeps confirming the programming mode. at this time, you can change the settings by pressing 1 of the 4 buttons., each button will change a different function.

in no order------
1. Beep/vibrate or both
2. page or not to page
3.back light
4. hood, truck, or both

the remote will give 2 long beeps when it exits the programming

Aug 20, 2009 | Directed Electronics 479V Remote Gen 2...

Not finding what you are looking for?
VIPER 7141V VIPER 4BUTTON REMOTE  7141V Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Viper Vehicle Parts & Accessories Experts

Tre Elkins

Level 3 Expert

643 Answers

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

Joseph Gallucci

Level 2 Expert

120 Answers

Are you a Viper Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...