Question about Homelite Consumer Products 9.0 Amp, 14 In. Chainsaw

1 Answer

How much bar & chain oil do need each time you use the machine

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 50 Answers

The best idea is to top it off when you fuel up.

Posted on Jul 22, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which oil do i use in a ryobi C4620 chainsaw?


Do NOT use lightweight motor oil for that bar! Use only bar/chain oil for it - nearly any brand will do just fine, but it needs to be bar/chain oil. Bar/chain oil is specially formulated to stay on the bar & chain in use - motor oil will fling away & your bar won't get the lubrication it needs.

For fuel mixing, use nearly any brand of 2-cycle oil, which is specially formulated to provide lubrication even when it's mixed into your fuel. Use about 3.2 ounces of 2-cycle oil per every gallon of gasoline - a little more won't hurt (it'll make the saw smoke a little), but never use less. Always shake the gas can just before you refill your saw's tank - shaking helps make sure the oil & gas are well-mixed.

Mar 13, 2013 | Garden

1 Answer

What Oil is used for the bar & chain lubrication


Hi khipiercy...
You will use "Bar and Chain Oil" for your chain and bar lubricant...it is specially formulated to be used on chains and bars of chainsaws...
You can buy it at any Loews,HomeDepot, Ace Hardware, etc.
Please take time to rate me

Sep 22, 2011 | McCulloch Garden

1 Answer

What kind of oil do I put into my toro expand it chainsaw?


CHAIN OILER See Figure 18. ? Use Premium Bar and Chain Lubricant. It is designed for chains and chain oilers and is formulated to perform over a wide temperature range with no dilution required. ? Remove the cap and carefully pour bar and chain lubricant into the chain oiler tank. ? Replace the cap and tighten securely. ? Check and refill the chain oiler tank every hour when using an electric power head or every time the engine is fueled when using a gas power head. NOTE: Do not use dirty, used, or otherwise contaminated lubricants. Damage may occur to the oil pump, bar, or chain.

Sep 01, 2011 | Toro Garden

1 Answer

I have a husky 235 (e = ?) & it has been very troublesome for me. My little 3000 Echo saw i purchased in 1995 (& have had refurbished once since then) outshines the husky reliability-wise. On the...


The oiling on this model has been an issue for a long time, the first and main problem was distortion of the bar pad due to heat from the muffler, and the ommision of a metal strengthener in the pad itself, what happens then is as the bar nuts are tightened, the bolts try to pull throught the bar pad, this creates a bulge around the bar bolt and causes the delivery tube to collapse, there was a later crankcase with steel inserts around the bar bolts to prevent this, and an updated delivery tube, you can tell when this has happened as the oil drips onto your shoes rather than going onto the chain, let me know it you need any more advice or i have not explained this very well, what has the dealer said about the oiling problem?

Apr 15, 2011 | Husqvarna "Chain Saw - 16" Bar, 3 Hp

2 Answers

In addition to the gas and oil mixture there is a place for just oil....what do I need to put in there ?


That's for the bar&chain oil. It dribbles onto the chain as the saw runs, lubricating the where the chain slides over the slot in the edge of the bar. Without this oil the chain & bar will overheat pretty quickly, ruining both the bar and the chain.
Good luck

Nov 22, 2010 | McCulloch 16 Inch Gas Chain Saw MCC1635AK

1 Answer

Is there a satisfactory substitute for "bar & chain" oil?


No. Bar & chain oil is made so it will stick to the chain and lubricate and it can deal with the heat generated by the chain. It's also thick enough so it won't run freely out of your saw. It doesn't really make any difference who makes it, just that it's bar & chain oil.

Sep 30, 2010 | Do It Best Bar And Chain Oil

1 Answer

Chain oil is not oiling chain. Could it be clogged? First time I used machine.


Is it new (return it!)? Did you put bar and chain oil in the reservoir?
Oil System Plugged.
  1. Remove the clutch cover, bar, and chain, clean the bar groove, any holes and passages on the rear of the bar (both sides, consider rotating the bar) Clean the saw’s oiler hole and channel. Start the saw and see if it oils when revved up. If yes reassemble your saw. If no, continue with 2.
  2. Insert a blunted, hooked piece of wire through the oil filler hole and pull the hose in the oil tank out (clean or replace, difficult to determine serviceability). Work your way through the linkage cleaning and replacing any defective parts as you go. Carefully check the hoses for cracks especially at bends and connections. If equipped with an oil pump it is usually behind the clutch (clutch is a left handed thread). Please make extensive notes & some digital pictures will help during reassembly. GL
Lou
Providing a make, model & serial numbers help us help you. Without these we can only provide a general answer. There are in excess of 5000 different chainsaws.

Nov 24, 2009 | Poulan Garden

3 Answers

I have a Spear & Jackson petrol chain saw


  • bad oil leak on spear and jackson chainsaw.

Nov 22, 2009 | Garden

2 Answers

Chain and bar do not seem to be getting oil. Have not had to refillbar oil in a long time.


Oil System Plugged.
Remove the clutch cover, bar and chain. Clean the oiler hole and channel. Start the saw and see if it oils when revved up. If yes reassemble your saw.
If no a blunted, hooked piece of wire can be used to pull the hose in the oil tank out. I recommend the filter be replaced. Work your way through the linkage cleaning and replacing any defective parts as you go. Carefully check the hoses for cracks especially at bends and connections. If equipped with an oil pump it is usually behind the clutch (clutch is probably left handed thread). Please make extensive notes & some digital pictures will help during reassembly. GL
Lou

Oct 15, 2009 | Poulan Pro 42CC 2 Cycle Chainsaw, 18"

1 Answer

Husqvarnar model no 345 oil feed problem


First thing check the feed hole through which the oil is delivered to the bar itself for debris,secondly the worm gear turning the pump shafft need only be slightly damaged to hamper full oil flow , next take the oil filler cap off, (with the bar ,chain ,bar plates, and oiler removed ) look where the oil pick up is in the case half and remove it and check for clogging and / or tears in the rubber hose,
if the cap is equipped with a breathing filler cap check make sure the cap breathes this will also hamper maximun oil flow capacity,
I stand by this , as I have dealt with product for close to 2 decades and know it intimately
W.O.T. Technologies

Oct 27, 2008 | Husqvarna Chain Saw 20" Bar

Not finding what you are looking for?
Homelite Consumer Products 9.0 Amp, 14 In. Chainsaw Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Homelite Garden Experts

roeb

Level 3 Expert

641 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Mike Squire

Level 2 Expert

420 Answers

Are you a Homelite Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...