Question about Duravit 0910100005 Happy D Toilet Cistern - White

Open Question

Fitting new cistern button - Duravit 0910100005 Happy D Toilet Cistern - White

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cistern leaks into bowl


Depends on the country you live in, but in North America, you need a new Flapper in the bottom of the system. Cheap to buy and take 10 minutes to fit.

Pictures and video of them.

Cistern Google Search

Nov 07, 2016 | Home

Tip

FIXING A TOILET THAT WILL NOT FLUSH!!! a simple but very effective money saving...


This simple how to, is based upon most lever operated toilets, with the cistern mounted above the toilet bowl. The make and model of toilet used for this feature is of the following:
Toilet and internal syphon
DUDLEY ELITEDudley S7 Cascade syphon
Problem:
My toilet will not flush, but the ball float valve is working and there is water in the cistern; no leaks present and the flushing lever is not broken or disconnected, what do I do?
Answer:
first isolate the water to the toilet or the main water supply to the house. Bail out the water from the cistern using a small jug or cup, (or you can syphon the water manually using a hosepipe or similar pipe, a towel to cover your mouth, and either a bucket or the toilet bowl) and remove water from the bottom of the cistern with a sponge.


Changing the syphon in a toilet that is not close coupled is far easier as you do not need to remove the cistern from the wall!


Undo the lower of the two large nuts beneath the cistern using a large pipe wrench or pair of water pump pliers, now disconnect the flush pipe and push it to one side.
Place a bucket or bowl beneath the cistern and undo the Nut which is immediately below the cistern (syphon replacing nut), some water may be released by the syphon, take note of any washers that are removed as new ones need fitting when replacing the siphon.
Unhook the lift rod from the flushing lever and remove the syphon.


Inside the toilet syphon, there will be a small plastic piece of sheet called a diaphragm; you can fabricate a replacement using the plastic title cover on a DVD case. Cut this to the exact same size and shape as the original part, and fit this to where the original diaphragm was. This is your new replacement.


Refitting is a complete reversal of removal, be sure to fit any washers (preferably new ones) that you have taken out. Ensure everything is tight but do not over tighten before refilling the cistern



on Aug 09, 2010 | Plumbing

1 Answer

We have fitted a new ballcock on the watertank (cold) since then we have little cold water


Are you sure the ballcock is correctly adjusted to fill the tank to the required level? The float should have a screw on it which changes the height at which the valve is closed. if set too low you may not get enough head of water to feed the system. If set too high the tank will overflow.

This video deals with a toilet (WC) cistern but the principal is the same for any ballcock valve system.

How to adjust the cistern ballcock in your WC cistern get better flush

Apr 15, 2015 | Home

1 Answer

How to get lid off estilo plastic wc cistern


Push in the sides of the cistern at the top, the buttons are fixed to the top and come away with it. Instruction and fittings are inside.

Sep 01, 2013 | Home

1 Answer

Low-level Cistern - leaking from syphon back nut.


Assuming the seal washer is inside the cistern and there are no cracks in the cistern itself you could apply a silicon sealant to the seal washer inside the cistern.

Apr 04, 2010 | Plumbing

1 Answer

Push button not operating fully/correctly. cistern flushes sometimes, but not always and is only two years old. It's a Grohe concealed cistern.


hey,
Check your button/s panel, check that the hoses are connected firmly.
Disconnect the hose and blow air through it, does it work now?
If it works ok, you need a new buttons panel. (or fix it).
If problem remains, you need to disassemble the pneumatic valve and check / clean/ repair it.
Look at this guide that might help you. though it is not the exact model, principle is the same.
Have fun
Avi

Grohe GD2 flush system concealed cistern repair fix and disassembly...

Nov 23, 2009 | Grohe Home

3 Answers

Cannot remove top of cistern


There are some dual flush cisterns where you have to depress one button to reveal a cavity in the second button. Put a screwdriver in that cavity to lever out the second button, then release the first button and prise that out.

Underneath the buttons is a screw which must be unscrewed to release the cistern lid.

Not sure if this will apply to you... but if not, good luck anyway.

Oct 29, 2009 | Duravit 0910100005 Happy D Toilet Cistern ...

1 Answer

When cistern fills with water it leaks into the bowl


Hi,

This is caused by the 'syphon' mechanism sticking, quite often nowadays the 'brilliant' plastic push button/ syphon combo sticks, and most toilets are fitted with an internal overflow, lift the lid on the cistern and check for anything causing an obstruction.

More often than not, it's a tiny bit of scale that causes such a headache, and the fact that nothing is made with any quality nowadays!

If you can't see what's wrong call a plumber, he/she will solve it.

I hope this helps

Steve

Jul 09, 2009 | Duravit 0910100005 Happy D Toilet Cistern ...

Not finding what you are looking for?
Duravit 0910100005 Happy D Toilet Cistern  - White Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Duravit Home Experts

paulcarew

Level 3 Expert

2458 Answers

Lawrence Oravetz

Level 3 Expert

9324 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

14580 Answers

Are you a Duravit Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...