Question about GE Profile Prodigy WPSE4200A

Open Question

On and off switch controll board - GE Profile Prodigy WPSE4200A

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ge washer GFWS3500L0WW Has no power on the control board...Its dead...I get 120 volts at the door switch but nothing back out that returns to the control is this a faulty door switch?


Not likely that the door switch is killing the power to the control board.
It may stop the machine from going through cycles, but it shouldn't turn off the control. It's probably that the door switch has one side always powered and they connect it to the other side of AC when they want it to engage or the relay for the door switch happens to be stuck in this mode when the control board went out.

Jul 21, 2016 | GE Washing Machines

1 Answer

74008072 Range Control Board


try a used appliance dealer, he will more than likely have many of those pcb boards that are junk that you can probably take for little or no money and harvest the switch from there. i have never found loose components like that for sale.

Sep 26, 2013 | Maytag 74008072 Range Control Board Part

1 Answer

New Control Board or can it be fixed?


it can repaire.....replace that micro switch......

Jun 05, 2013 | LG Washing Machines

1 Answer

AK-RK04S-12+AK-TF04 Wireless Remote Control Switch Board & Remote Control . I need the wiring diagram and instructions for this please thank you


I received this wireless remote and want to use it for my generator, i would like the wiring diagram and instructions for this

Please give me manual book AK-RK04S-12+AK-TF04 Wireless Remote Control Switch Board & Remote Control (White)

Thanks

Feb 03, 2013 | FocalPrice AK-RK04S-12AK-TF04 Wireless...

1 Answer

Replaced baking element and still does not heat


take a multimeter and assure that you have power coming to the element you need to take off the rear panel of the range as well as the panel that covers the control board assure that you have power going to the control board and then leaving the control board as well if it is not leaving the control to go to the switch then you would replace the control board if it is leaving the control board yet not going past the switch then you would replace the switch any further questions message me back and please rememeber to rank how this opinion has helped it allows me to help others in similar situations Thanks Rick

Mar 14, 2011 | Magic Chef CER3725AA Electric Kitchen...

1 Answer

Re: Maytag Neptune Washer. Loaded 2 jackets (whites requiring bleach), added usual Gain detergent (granules), plus small amt. of bleach in dispenser, then started cycle. Then poured bleach into machine...


DO = Door Open
Door monitor switch in door lock mechanism is not able to communicate to the control board is open.
1.Make door is closed.2.Check for loose wire connections at switch and/ or machine control board.
3.Check for failed door monitor switch.
4.Check inputs and outputs at machine control board.


FL = Failed To Look


Door lock monitor switch in door lock mechanism unable to communicate to control board the door is locked.


1.Check wire connections in harness leading from machine control board to door lock mechanism.2.Check solenoid and door lock enable switch in door lock mechanism.

Dec 31, 2010 | Maytag Neptune Washer

1 Answer

F32


The F32 error code indicates a water level pressure switch failure. This is normally caused by wiring connection problem or a failed pressure switch. If you are able to unplug the washer and remove the top panel, you can check the wiring connections between the control board and the water level pressure switch. To remove the top panel (with the washer unplugged), take out the screws at the very back of the top panel and slide the panel back and then pick it up and remove it from the top of the washer. The pressure switch is on the top of the right side panel toward the back of the washer.

If the wire harness connection between the pressure switch and the control board is okay, then you will probably need to replace the pressure switch to correct this problem. The part number for the pressure switch is 8181695. You can order this part from the Sears PartsDirect website www.searspartsdirect.com .

The F28 error code indicates a communication error between the main control board and the motor control board at the bottom of the washer by the drive motor. A loose wiring harness connection can cause this problem. It can also be caused by a failed motor control board, a bad drive motor or a defective main control board. You may be able to check the wiring harness connection to the motor control board by unplugging the washer and removing the bottom from service panel. To remove this panel (with the washer unplugged), take out the screws at the very bottom of the panel and then pull the panel down and out to remove it. Access to the motor control board may be limited. You may be able to check to make sure that wiring connections are firmly secured on the motor control board. If the connections are okay and you continue to get the F28 error code, you may need to replace the motor control board.

Nov 02, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

3 flashing light....Aire-Flo furnace AF80MPA100B5A


That control board is several hundred dollars. If I may make a suggestion, take a jumper and when the inducer fan starts, jump out the pressure switch. If it starts, it's not the board but a bad switch, hose or blocked exhaust vent.

Jan 14, 2010 | AOC Heating & Cooling

1 Answer

Commercial generator 20kv not working properly


Troubleshoot like this:
1 - With the generator control in Auto, jumper from terminal 3 to 4 on the control board. Generator should start without transfer switch doing anything. If it won't you have a bad controller board.

2 - If the Generator started, remove the jumper - controller is OK. Next go to the 1st transfer switch and find the remote start terminals. These will be the same wires that were connected to controller terminals 3 and 4 at the generator. Use your jumper wire to connect them and see if the generator starts, if not there is something wrong between the switch and the generator, probably a broken wire.

3 - Don't forget to check the other switch, the remote start terminals of the switches connect in parallel across controller terminals 3 and 4 so that either switch can start the generator.

4 - Each switch should have some sort of a test button/switch, power down as much of the building as you can, then run the test function of each switch one at a time. Don't stand directly in front of the switch while you do this.


Nov 20, 2008 | Electrical Supplies

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...