Question about Acer Modem 56 Memory (91.12035.001)

Open Question

Gr?¼ne und rote Lampe brennen, Display sagt nichts

Ich habe dsa Modem einige Jahre nicht benutzt.
Da ich mit Mac arbeite. Da ich aber nun Faxe empfangen will und diese beim Mac einfach nicht zu empfangen sind, will ich nun das Modem wieder benutzen, auch wegen der Memory-Funktion. Wie oben beschrieben aber treten die Fehler auf:
grüne und rote Lampe brennen, Display sagt nichts

Posted by on

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


1 Points

Related Questions:

1 Answer

All lights flashing red one after anouther might need to.reset your.modem...on.the back all.the ports you.would either see a button.or.the.reset button.might.b loacted inside a hollow.hole...take somethng that is poinetd and hold it down.for.30sec...then u.might see all the lights flashng...unplug da.power.cord leave it.for.30.sec..turn it.on .the modem.shud.wrk.fine... If.nt.cntct.ur.internet.service.provider or.da.hardware.manufacturer

Nov 02, 2013 | 2wire (1000-000057-000) Modem

2 Answers

I'm trying to set up wireless internet for a laptop (Dell Latitude CPi) that was just given to me. The card is a TDK Global Freedom 5660 v.90. My router wants to know the 12 digit MAC address and I don't...

You can display the MAC address and the IP address of your network card by click on Start - Run - type cmd and press Enter.
This will open a DOS command window - type ipconfig /all then press Enter The MAC address will be displayed as a Physical address.

Jan 27, 2010 | AB Soft TDK Global Freedom 5660 Modem

1 Answer

Need new ip and mac adress for sb5100 motorola for southwest

To get new IP unplugg power for 1 minutes the plug the power back in. MAC address is a unique identifier specific to that modem. To get a new MAC address you will have to buy a new modem.

Sep 13, 2009 | Arris SB5100 SURFboard DOCSIS 2.0 Cable...

1 Answer

Blocking a user from internet

if you log into your router/modem you shuld be able to enable mac filtering add the mac address's you simply want to have access and they will be denied, alternatively you can turn off the dhcp so your router doesnt assign them access - either will work but i prefer the mac filtering.

ipconfig /all in a dos box will display mac address.

Mar 06, 2009 | 2wire Modems

1 Answer

Want sound driver for my computer

HI Rashmi,

Get da drivers from da link below»

You will have to select da OS type that you have on ur comp and just navigate through da drives table n locate n install da driver u need. It will most likely will be listed as Original Realtek High Definition Audio Driver.


Jan 20, 2009 | Agere All 56K Modems: 56K V.92 Lucent/...

1 Answer

No internet when using router

Your modem has already registered itself with the MAC address of your computer, so it doesn't recognize the MAC of your router. In cases like this you have two options:
  1. Configure your router to clone the MAC of your computer
  2. Connect the router to your modem and do a soft reset so the modem registers itself with the MAC of your router.
Clone MAC - Go to your routers Admin web interface and on the main page you should see the "Router MAC Address" section at the bottom. Select "Use Computer MAC Address" and click "Apply" and your router should reboot and you'll be back in business.

Soft Reset
- Plug the modem into the router via the ethernet cable then do a soft reset.

To do a soft reset, do the following:
  1. pull the power cord from the modem
  2. count to 5
  3. hold down the Reset EMR button on the modem
  4. plug back in the power
  5. count to 30 while holding the Reset EMR button (the modem should be blinking a lot)
  6. release the Reset EMR button and see what happens.

Jul 07, 2008 | Modems

2 Answers


That should be plug and play.

I would check with Motorla and see if there have been issues with it.

Jun 11, 2008 | Arris SB5100 SURFboard DOCSIS 2.0 Cable...

2 Answers

No longer dialing Lond Distance

If your modem can fax a local number or dial-up an Internet Service Provider in your Local Area then your Internal Modem is just fine. Check if the configuration of your Modem to access outside long-distance number. Go to your Control Panel-Open Phone & Modem Options-Dialing Rules (Tab)- then click on EDIT Button. You can enter the number needed to have a long distance dialing. If you don't know the number needed for long-distance dialing then ask your Local Phone Service Provider.

Apr 04, 2007 | Smartlink (I56KSPF00) Modem

Not finding what you are looking for?
Acer Modem 56 Memory (91.12035.001) Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acer Modems Experts


Level 3 Expert

2598 Answers

Clive Gray

Level 3 Expert

1479 Answers


Level 2 Expert

99 Answers

Are you an Acer Modem Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides