Question about Reddy Heater-30-55,000 BTU Variable

1 Answer

How do i adjust the presure - Reddy Heater-30-55,000 BTU Variable

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 22 Answers

On the back of the unit you will find a small pipe plug with a slot a screw driver turning the plug clockwise increases the pressure and clock wise decreases, you need the gauge to adjust to the correct pressure, and screwdriver needs to be away from slot for correct reading.

Posted on Mar 10, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a everbilt 1 hp shallow deep well jet pump. It does not have good pressure. I was unable to put the extended plastic jet adaptor in the pump. I could not install it


you can adjust the pump switch to get higher presure its the box on the outside of the pump with two screws, one is an upper limit screw to turn the pump off at the proper presure ,the other screw turns the pump on when it gets to a low presure,Make sure electric to pump is off.

Jun 11, 2017 | Plumbing

1 Answer

How do i change presure setting - Respironics 1043237


If this is on a CPAP machine, I would not attempt to adjust this myself! The dealer where you got this from would be able to adjust this if it is needed.

Feb 19, 2017 | Respironics Health & Beauty

1 Answer

Sears 2600 psi power washer


there should be a low presure tip for dispensing wash cleaner or if you have an adjustable wand turn it to low presure setting also make sure the suction tube is open some have a adjustable filter...good luck

Jul 25, 2010 | Briggs & Stratton 2200 PSI Gas Pressure...

1 Answer

Wont shift while driving


  • Check the clutch cable first and then adjust it. And if the adjustment won't work check the clutch linning and the presure plate and also the release bearing if still in good shape.
  • If you have additional questions don't hesitate to reply to this solution.


I’m happy to assist further over the phone at https://www.6ya.com/expert/ramy_d9e7ebea3891f482

Jun 15, 2010 | 1994 Dodge Intrepid

1 Answer

What are the tyre presurers for two up riding


30 psi front, 40 psi rear for maximum load. You'll have to adjust the suspension according to how much weight is on the bike. Tighten suspension until the rear tire does not rub under the fender when you negotiate bumps.

Good Luck
Steve

May 24, 2010 | 2000 Harley Davidson XL 1200 C Sportster...

1 Answer

Gun will not drive pins flush with wood. Wood is


What is your air pressure setting. A finish nailer such as this usually requires 70 lbs to drive flush. Adjust air to this value and test fire in scrap. Keep adjusting air presure until nail drives flush.

Nov 23, 2009 | Senco 4N0001N Finishpro 11 23 Gauge Micro...

1 Answer

I have a craftsman 2 hp air compressor,(model#919.176320) that fills fine,but then will not refill,as if there is presure in the line.The instructions say it will fill to 125lbs,Then refill(cut in...


Hi,lets see what we can do.The air compressor has a relief valve,like check valve .that is not working.The valve reliefs the head pressure so it can be restarted at any time.If pressure is on top of the piston pushing down it can not restart.The pressure in the head on top of the piston is greater than the pressure under the piston.I hope this helps,if you need more assistance feel free to contact me.,,roniecon@gmail.com

Jul 10, 2009 | Air Tools & Compressors

1 Answer

Adjusting front suspension


yes you are going to need a technical manual with the gauged settings of the factory. This will set to default factory and you can then adjust to what the setting adjustments are to fit your confort.

Jan 29, 2009 | 1995 kawasaki KLE 500

1 Answer

Noises , noises , noises


the lifters are hydrulic and require no adjustment unless the pushrods have been swaped out to adjustables, the stock ones are solidlength like a car you need to undo a pushrod cover to see them we would need to know the thread pitch to determin the adjustment if there adjustable check the lifter block screen for trash also

Jan 04, 2009 | Harley Davidson Harley-Davidson Motorcycle...

1 Answer

Gas adjustment.


To adjust gas presure you need a wg presure gauge

Oct 27, 2008 | Heating & Cooling

Not finding what you are looking for?
Reddy Heater-30-55,000 BTU Variable Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Reddy Heating & Cooling Experts

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Mack Baxter

Level 3 Expert

383 Answers

T bone 1963

Level 2 Expert

69 Answers

Are you a Reddy Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...