Red Line Synthetic Oil 60202 Lead Substitute 12/12oz Logo

Related Topics:

A
Anonymous Posted on Feb 12, 2014
Answered

Alternative for Desmocap 11

Urethane Polymer

Answer This Question

1 Answer

ADMIN Andrew

ADMIN Andrew

Level 3:

An expert who has achieved level 3 by getting 1000 points
Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.

  • Redline Bikes Master 66,967 Answers
  • Posted on Aug 30, 2023
ADMIN Andrew
Redline Bikes Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
Top Expert:

An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.

Joined: Nov 14, 2009
Answers
66967
Questions
3
Helped
5088688
Points
379841

The product itself?

Desmocap® 11 A

Covestro AG https://solutions.covestro.com > products > desmocap
Desmocap 11 A is a branched polymer with ether and urethane groups; contains crosslinking, blocked isocyanate groups. It is suitable as a raw material for ...

Desmocap 11 A

 Covestro AG https://solutions.covestro.com > desmocap > des...
Desmocap 11 A is a branched polymer with ether and urethane groups; contains crosslinking, blocked isocyanate groups. It is suitable as a raw material for ...
3 pages

Desmocap® 11 (TDI) - Covestro - Coatings Ingredients

 SpecialChem S.A. https://coatings.specialchem.com > product > r-covestr...
Desmocap® 11 by Covestro is a solvent-free, high viscosity, branched polymer with ether and urethane groups. It contains crosslinking, blocked isocyanate ...

DESMOCAP® 11 by Covestro - Paint & Coatings

 UL Prospector https://www.ulprospector.com > Coatings > Detail > D...
A branched polymer with ether and urethane groups; contains crosslinking, blocked isocyanate groups. Used as a raw material in the flexibilisation of epoxy ...

Desmocap 11 - Covestro - Industrial Adhesives and Sealants

 SpecialChem S.A. https://adhesives.specialchem.com > product > p-coves...
Desmocap® 11 by Covestro is a branched polymer with ether and urethane groups contains crosslinking, blocked isocyanate groups. Has good compatibility with ...

Desmocap® 11 - Adhesives & Sealants

 UL Prospector https://www.ulprospector.com > Adhesives > Detail
Desmocap® 11 has a viscosity at 23? of 100,000 ± 25,000. It is a branched polymer with ether and urethane groups, used as a raw material for use in the ...

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I need a urethane Driver Belt for my Shopcraft model T7060-20T Band Saw. Part No. BMTJL 14-030
Try this site

http://www.sgtool.com/product-category/urethane-band-saw-tires/urethane-band-saw-tires-by-dimension/?filtering=1&filter_band-saw-size=119
Read full answer
Apr 09, 2016 • Saws
0answers

Need new tires for an Ellis 1800 Band saw. The wheels measure 11-3/4" what size tires do I need?
Read full answer
Be the first to answer Mar 16, 2016 • Cars & Trucks
0helpful
1answer

SPRING URETHANE BLACK 12.7MM ID X 25.0MM OD X 38.1MM TH , DUROMETER ; SHORE 95A, B-116-064 for my jazzy 1107 Power Chair are cracked and busted causing my rear wheel caster assembly to lean backwards in...
I know that 95 durometer EVA is available from other sources like shoe findings suppliers. This is about 1/2" by 1" by 1.5" and if a mechanic was able, he could fix you up with that. If that is what you need, they could help you out without having to replace the whole assembly.
Read full answer
Feb 28, 2017 • Health & Beauty
0helpful
1answer

Back glass replacement
Remove all old glass an urethane and replace with new glass and urethane.
Read full answer
Jun 18, 2013 • Isuzu Rodeo Cars & Trucks
0helpful
1answer

Back glass replace
remove old glass and urethane and replace with new glass sans urethane
Read full answer
Jun 18, 2013 • Isuzu Rodeo Cars & Trucks
0helpful
1answer

How do u replace the passenger side quarter glass on a 02 Chevy Tahoe LS
First you have to "cut" the old one out. There are a couple of tools to do this. "Piano wire". (its actually a small diameter cable you pull back and forth that cuts the gasket) Blade (pnuematic powered tool that slices through the urethane) Once you have the old glass out, remove all of the old urethane, and apply new urethane. Comes in a tube, pretty much like caulking. Press it in place, put some painters tape all around it so it doesnt slide before the urethane dries and thats it. Sounds easy, and it is if you are in the business. You can get the glass cheap from a salvage yard. If its a nice Tahoe, I would recommend getting Safelite or other glass installer to do it. EZ to scratch up your paint with the wire, and the pnuematic tool will set you back more than the install would cost.
Read full answer
May 22, 2012 • 2002 Chevrolet Tahoe
1helpful
2answers

Where can i buy a new rubber for the tire for pts turbo 1000?
Read this....

http://airless-tires.typepad.com/airless-tiresorg/2010/07/pts-turbo-trainer-tire-11-years-of-sales.html

Short answer = find an Air Free Savannah Cruiser 27 x 1 3/8 (17-18mm) Urethane Airless Bicycle

http://www.airfreetires.com/shopping/p-101-27-x-1-14-nu-teck-savannah-cruiser17-18-630.aspx
Read full answer
Feb 26, 2011 • Cycling
1helpful
2answers

The rear window to my van came off and shattered during a windstorm... i bought a window off of craigslist.. and can't install it. I dont need it to work,i just need it to go back on.. my bf is taking...
is it a fixed glass or a moveable glass.

Fixed glass is placed against a bead of urethane sealer, like caulking.

Window, Liftgate, Stationary Removal
ssw~us~en~file=ani_caut.gif~gen~ref.gif WARNING: SAFETY GLASSES AND GLOVES MUST BE WORN.
ssw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use only urethane for after-seal to service air and water leaks in urethane seal. Failure to do this may result in additional leaks.
ssw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Allow all glass parts installed with urethane ample time to cure. If ample time is not allowed, glass may come loose and/or leak.
  1. Remove window wiper pivot arm (17526) .
  1. Remove all window glass stops.
  1. Using Rotunda Glass Adhesive Cutter 118-00050 or Rotunda Deluxe Glass Adhesive Cutter 163-00001 or equivalent, follow manufacturer's instructions and cut seal and dam around entire outer edge of windshield glass (03100) .
  1. Remove glass from vehicle.
  1. Trim urethane left on flange with a utility knife or razor blade until surface is smooth and free of cuts. It is not necessary to remove all urethane from the flange if it is cured. However, at no point should existing urethane material exceed 2.54mm (0.10 inch). NOTE: If urethane has not cured completely, remove all uncured urethane using care not to smear urethane on component parts.
    Check flange sealing area for damaged sheet metal or foreign objects which may have caused, or may cause, glass breakage. Service sheet metal if necessary.
Installation
  1. If existing urethane on metal flange has become contaminated, cut away contaminated urethane with a utility knife or razor blade.
  1. If painted sheet metal has been exposed anywhere along the flange, apply Urethane Metal Primer WSB-M2G234-C or equivalent over the painted surface using a clean brush. NOTE: A minimum of 30 minutes is required for primer surface to dry.
  1. Place the windshield glass on a low, stable work surface, inside up. NOTE: Wipe off immediately after application because it flash-dries.
  1. Using a lint-free cloth, wipe outer 25mm (1 inch) of inside glass periphery with Urethane Glass Wipe WSB-M5B280-C2 or equivalent.
  1. Position mouldings on glass. ssw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Allow all glass parts installed with urethane ample time to cure. If ample time is not allowed, glass may come loose and/or leak.
  1. Thoroughly shake and stir Urethane Glass Primer WSB-M2G314-B or equivalent to ensure uniform pigment mixing.
  1. Using a clean brush, apply primer around entire periphery of glass on inside surface as shown. (Allow at least five minutes drying time.)
  1. Properly align glass to body.
    1. Make sure lower windshield glass stops are in place at bottom of windshield glass opening.
    1. Place windshield glass into opening. Center it top and bottom, side to side, with about equal clearance around opening.
    1. Using masking tape or crayon, make alignment marks at points on both the windshield glass and the window opening.
  1. Remove windshield glass from vehicle and place back on work table.
  1. Apply an even bead of Urethane Adhesive WSB-M2G316-B on top of existing urethane around entire window opening using an air pressure cartridge gun. Air line pressure should be around 276 kPa (40 psi). The bead should be large enough to seal the windshield glass but not cause expulsion into vehicle.
  1. Install windshield glass onto vehicle, taking care to align marks on glass to those on body. This must be done within 10 minutes of applying urethane.


Read full answer
Dec 20, 2010 • 1995 Ford Windstar
0helpful
1answer

How do I replace the back window?
Remove the black vinyl trim from the edge of the glass. Remove broken glass & urethane adhesive from the metal pinchweld leaving a thin layer (approx 1/16") of urethane for new new urethane to adhere to. Vacuum broken glass. Prime nicks to the metal to protect from rusting (also insuring a good surface to bond to). Attach vinyl reveal molding to glass (unless it's a "T" shaped push in type - it would install after the glass is set). Clean and prime the replacement glass. Apply new urethane adhesive. Set glass in place.Slide the metal joint cover in place on the molding (at bottom in the center). Clean outer surface of glass. Allow for safe drive away as noted by urethane manufacturer.
Read full answer
Sep 25, 2009 • 1995 Oldsmobile Cutlass Ciera
2helpful
1answer

R/H rear quarter window repalcement
tv is the wrong adhesive. you must use urethane with a primer. it is available at any QUALITY parts store (NAPA or Carquest comes to mind)


Material Item Specification Urethane Metal Primer Essex U-413
WSB-M2G234-C Urethane Glass Prep Essex U-401
WSB-M5B280-C Urethane Glass Primer Essex U-402
WSB-M2G314-B Urethane Adhesive Essex 400-HV
WSB-M2G316
Removal
All vehicles
ani_caut.gif WARNING: To prevent glass splinters from entering the eyes or cutting the hands, wear safety glasses and heavy gloves when cutting the glass from the vehicle.
  1. Remove the C-pillar trim panels. For additional information, refer to Section 501-05.
3-Door, 5-Door
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the lower corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 60 mm
    1. 75 mm
    1. 90 mm
    a0074767.gif
Wagon
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 30 mm
    1. 50 mm
    1. 40 mm
    a0074768.gif
4-Door
  1. ani_caut.gif CAUTION: Make sure the cutting blades are changed where the cutting depth changes to avoid damage to the body and trim panels.
    NOTE: Some resistance may be encountered when cutting through the glass locating pegs in the upper right and lower left corners of the glass.
    NOTE: Lubricate the existing urethane adhesive with water to aid the special tool while cutting.
    Using the special tool, place the flat side of the knife against the quarter glass window. Start at the top and work towards the corners cutting to the given maximum depths:
    1. 20 mm
    1. 25 mm
    1. 45 mm
    1. 50 mm
    1. 55 mm
    1. 70 mm
    1. 150 mm
    a0074769.gif
All vehicles
  1. Remove the rear quarter window glass.
  1. Using a soft brush or vacuum, remove any dirt or foreign material from the pinch weld.
Installation
ani_caut.gif CAUTION: When installing urethane installed glass parts, the vehicle must not be driven until the urethane adhesive has cured. At temperatures above 21°C (70°F) and relative humidities above 50%, adequate cure time is typically 24 hours. (Refer to Essex drive away chart for the cure times as temperatures and humidity vary.) Inadequate or incorrect curing can adversely affect the retention of the quarter window glass.
  1. NOTE: Avoid scratching the pinch weld.
    Trim the remaining urethane adhesive. The urethane adhesive must be smooth and free of cuts and contamination after trimming. Avoid touching the urethane adhesive after preparation.
    a0005586.gif
  1. Apply the urethane metal primer to any exposed or damaged metal on the pinch weld.
  1. If reinstalling the original rear quarter window glass, remove the excess urethane adhesive.
  1. Clean the rear quarter window glass with a non-alcohol based window cleaner.
  1. ani_caut.gif CAUTION: Wipe off the urethane glass prep immediately after each application because it flash dries.
    If installing a new rear quarter window glass, apply urethane glass prep twice around the glass surface to be urethaned.
  1. If installing a new rear quarter window glass, apply urethane glass primer to the same area that was prepped in the previous step. Allow 5 minutes to dry.
  1. Cut the urethane adhesive applicator tip to specification.
    a0016835.gif
  1. Apply a bead of urethane adhesive on top of the existing urethane bead on the pinch weld. Make sure that all gaps in the urethane adhesive are smoothed into one continuous bead.
  1. Position the rear quarter window glass to the flange, and press the retaining tabs into the flange to engage.
    an0459b.gif
  1. Install the rear quarter window glass.
  1. Check the rear quarter window glass installation for air or water leaks through the urethane seal.
  1. Install the C-pillar trim panels. For additional information, refer to Section 501-05.
Read full answer
May 29, 2009 • 2004 Ford Focus
Not finding what you are looking for?

View Most Popular

Red Line Synthetic Oil 60202 Lead Substitute 12/12oz

  • Vehicle Parts & Accessories

Related Question

I need a urethane Driver Belt for my Shopcraft model T7060-20T Band Saw. Part No. BMTJL 14-030

  • Saws

170 views

Ask a Question

Usually answered in minutes!

Popular Questions

My kic fridge have 2 compartments. Freezer and fridge. only the fridge part dont work help please

Red Line Mens Classic Gmt Black Dial...

Changing gear oil 800 Intruder

Redline 75W90 Gear Oil for Rear...

Roof on my 1997 Saab 900s convertible not working

Red Line W0133-1841080 Power...

WHAT TIME IS IT NOW IN iSRAEL

Red Line Mens Classic Gmt Black Dial...

What would bethe dependent variable if i am calculating the amount of water in an apple

Red Line 30804 Non-slip Continuously...

Top Redline Bikes Vehicle Parts & Accessories Experts

k24674

Level 3 Expert

8093 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

66967 Answers

Jonathan Buck
Jonathan Buck

Level 3 Expert

446 Answers

Are you a Redline Bikes Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...