Question about Husqvarna Viking 1

Open Question

Husqvarna 183 fuse - Husqvarna Viking 1

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


SOURCE: husqvarna model 183 foot control no power

anytime the machine does not respond like it's suppose to then it needs to be checked, the foot pedal could have gone bad, or the the sewing machine plug where the foot pedal goes may have gone out

Posted on Mar 27, 2012


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I choose stitch 2:07 for darning on the Emerald 183 Husqvarna Viking machine

Press the Menu button below the + for stitch length adjustment to rotate through the stitch menus. When you see 2 LEDs, you should be on the correct menu. Then press button 7 in the stitch selection area. Confirm this by checking the stitch selection on the display. (Make sure that you have the C foot in place.)

I hope this helps.

Cindy Wells

Jul 25, 2014 | Husqvarna Sewing Machines

1 Answer

Husqvarna model 183 foot control no power

anytime the machine does not respond like it's suppose to then it needs to be checked, the foot pedal could have gone bad, or the the sewing machine plug where the foot pedal goes may have gone out

Mar 27, 2012 | Husqvarna Viking 1

1 Answer

My Husqvarna Viking Emerald 183 has always had a problem with the needle up needle down button - after pressing it once, it often sews anywhere from 3 to 20 stitches. More recently, the machine keeps...

There is a sensor on the upper shaft that recognizes the position that the machine is in. A small disk on the upper shaft that has sections removed from it will block the sensor trough some range of operation and not at other times.I have never seen this in a 183, but you may have a sensor that is misaligned so that it doesn't completely block or clear the beam of light.It will need to go to an authorized repair center for repair. Some of these parts are very delicate. Don't risk damaging something working on it yourself.

Nov 06, 2011 | Husqvarna Viking 1

1 Answer

I have a Husqvarna Viking Emerald 183. I can't get it to feed fabric. The footer will move back and forth, but not up and down. So it's making stitches, but will only feed if I manually pull the fabric...

Do you have the feed dogs dropped? Check the feed dog and also the pressure on the presser foot. This knob is located at the left on the top of the machine. The normal setting is 4.

Feb 14, 2011 | Husqvarna Viking 1

1 Answer

Where can i purchase a foot pedal for my husqvarna emerald 183 sewing maching?

Check your local sewing machine repair store. Sometimes when a machine can't be repaired, they ask to keep the parts and sell them as used.

Mar 05, 2010 | Husqvarna Viking 1

1 Answer

Stippling for Viking emerald sewing machine

The switch in the back will lower the feed dogs.

If you need a manual - I found a PDF download by googling: viking emerald 183 manual

Feb 23, 2010 | Husqvarna Viking 1

1 Answer

My husquavarna Emerald 183 ights up when turned on but will not ''go''. I followed everything the manual said to do ie remove bobbin, plates, clean out any lint or threads etc then put it back together -...

sounds like an overload of some sort. Suggest you take it to an authorized husqvarna viking dealer for service. You can locate a dealer near you by visiting the husqvarna viking website and clicking on the Dealer link on the left-hand side of the page -

If you bought the machine new the warranty may still be in effect.

Feb 13, 2010 | Husqvarna Viking 1

1 Answer

Husqvarna viking emerald 183 - horizontal bobbin difficult to thread properly; any tips or how to?

I know the answer is a little late now...
I bought the machine a month ago and find that the bobbin picture is a bit misleading... i find putting the bobbin in the case, pushing the thread down over the hook thing (like in the picture) but then cutting the thread really short and putting the plastic cover on seems to work!
it is actually vary easy once you get the hang of it!

Dec 28, 2009 | Husqvarna Viking 1

Not finding what you are looking for?
Sewing Machines Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Sewing Machines Experts

Douglas Plant
Douglas Plant

Level 2 Expert

184 Answers

Tally Girl
Tally Girl

Level 3 Expert

1129 Answers

Derek Massey

Level 2 Expert

92 Answers

Are you a Husqvarna Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides