Question about HEALTHRIDER S300i Treadmill Motor Control Board 14470

Open Question

I have a S300i model, Set the speed control the actual speed does not change but the speed readout changes. also will not turn off (power) when the key is pulled.

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On model PLEF398DCH Frigidaire Professional Series electric range, my digital readout for the right side burners works fine. My left side digital readout is inoperative, but the burners work fine. Is there...


Good Afternoon Lee,

I understand that the left hand side digital readout is not working on your Frigidaire range, model# PLEF398DCH. I suggest resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Sometimes there can be a miscommunication between the different boards inside your appliance. Once you restore power, you will need to set the clock and start any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.

-Best Regards-
WP

Jun 27, 2014 | Frigidaire Kitchen Ranges

1 Answer

I cant change humidity levels


Hi Ra Ma,
After you have set the desired humidity, the readout will display the actual room humidity. It has a built in hygrometer which will be on the display while it is running.
You change it and it shows the actual levels.

See page 5 on manual.

http://manuals.frigidaire.com/prodinfo_pdf/Edison/2020266a0180en.pdf

Mar 02, 2014 | Frigidaire 70-Pint 2-Speed Dehumidifier...

1 Answer

I have a HealthRider S300i treadmill, but unfortunately, I don't have the included allen wrench. So far I've been unable to figure out what size allen wrench I need. Any idea?


you can try to rent a set at AutoZone. when you return it they will give your money back. try standard and metric. depending on manufacturer of treadmill.

Feb 09, 2011 | HEALTHRIDER S300i Treadmill Motor Control...

1 Answer

My blower does not shut off when I cut my car off. I have to pull the fuse under the hood to make it shut off. When it's on, it runs on high and I can change it or the tempature controll.


If you vehicle has the automatic temperature control system, where you can set the desired temperature using the digital temperature readout, then you most likely have a failing blower motor speed control module. This is an electronic module the controls the blower on/off and speed operations and when it fails it often won't shut off the blower when you shut off the vehicle which can result in a dead battery if you don't pull the power supply fuse. Its a small rectangular box located under the right side of the dash [passenger side] by the blower motor and isn't to hard to change. Hope this helps and good luck!

Jul 19, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

Changing temp readout on Midea Air Con Controller from F to C


  1. Make sure the unit is NOT on lock mode
  2. Press reset button for 2 second or until the Flashinf "F" appear on the temperature display or panel.
  3. Press Add button to change from Fahrenheit"F" to celius "C".
  4. Then press confirm and then cancel button to finish.

Jul 09, 2010 | Heating & Cooling

1 Answer

We have a Hampton Bay ceiling fan (about 10 yrs old) don't know the model. It will only turn 1 speed? When trying to change speeds with the chain pull it stays the same. It quit working for a while and I...


the fan changes speed by inserting a capacitor of different values in series with the motor .. direct drive to the motor is the fastest speed .. a large capacitor in series slows it down a bit and a smaller capacitor slows it down more ... so if your fan is running at full speed all the time then one of the capacitors is shorted or the switch is bad .. if its stuck on one of the lower speed settings then the switch has a bad contact .. the capacitors are mounted together in a small box with several wires going to the pull chain switch .. you can replace the capacitor box .. and you can replace the 3 or 4 position switch ... or you can remove all that stuff and put in a remote controled system .. that involves a box that just fits inside the fan .. it is hooked to AC power and neutral .. it then hooks up to the lilght and the fan giving you control over both .. you can vary brightness and fan speed .. you would no longer need the fan or light pull switch or the capacitors ... you could also get a new fan having such a controller .. since yours is fairly old it might be worthwhile to upgrade .. some of the remote controls allow you to set a temperature ..if the room goes above that temp then the fan turns on automatically and the speed is determined by how much higher the room temprature is from that set value .. some remotes also give you an additional very low fan speed .. thats nice at night when you just need a gentle breeze .. some also allow you to set a delay before the lights go out after you have clicked "turn off" ... that gives you time to exit the room or get in bed before the lights actually go out ... kindof nice features that might make it worth while to up grade .. to get parts for your old fan see this URL
http://www.ceiling-fans-n-more.com/hampton-bay-ceiling-fan-parts.php

since Home Depot sells hampton bay .. then they might have parts as well .. worth a try .. you can also see new models there ..

Jun 06, 2010 | Hampton Bay 52 In. White Redington...

1 Answer

Treadmill turns on but belt not turn on


Press the Stop and the Speed Up keys down while inserting the safety key this will get the into calibration mode. The next step is to press the Stop key one time. The Time window should read EP:2P. Some newer models may also say FP, Pass, or the like. This means that it passes the EPROM test. if it says 2F, FF or Fail then the upper console needs to be replaced
Press either incline key and the incline will calibrate automatically.
BE CAREFUL, THE TREADMILL WILL RUN AT FULL SPEED IN THIS NEXT MODE! DO NOT STAND ON THE WALKING BELT. Press the Speed Up key and hold it down until 85 is shown in the Distance window (some models may show the 85 number in another window
If the belt does not move in this mode then the controller board is defective and needs be replace.

Jun 01, 2010 | HEALTHRIDER S300i Treadmill Motor Control...

1 Answer

Amana Range, AER5515QAW


could be a bad bake element, bad temperature sensor, or control board problem

what does the oven readout display for temperature? if the readout agrees with the actual oven temperature ... it is probably the element

if the oven readout displays a much higher temperature it may be the temperature sensor (the probe in the oven cavity) or the control board

the temperature sensor can be tested by measuring its resistance with power off and unplugged from the control board, should be about 1100 ohms at 75F

If the sensor is good, then it is probably the control board ... in which case we can repair it for you at www.fixyourboard.com

Jul 20, 2009 | Amana AER5515QA Electric Kitchen Range

1 Answer

Dryer has power but will not start.


You might have a wiring issue in the dryer or a bad control board.

Feb 20, 2009 | Maytag Neptune MDG5500AW Gas Dryer

Not finding what you are looking for?
HEALTHRIDER S300i Treadmill Motor Control Board  14470 Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top HEALTHRIDER Exercise & Fitness Experts

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Techmotionusa.com
Techmotionusa.com

Level 2 Expert

161 Answers

Are you a HEALTHRIDER Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...