Question about Bosch SDS-plus BULLDOG Xtreme Rotary Hammer 11255VSR

Open Question

How do I remove the drive end shield - Bosch SDS-plus BULLDOG Xtreme Rotary Hammer 11255VSR

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install the alternator belt in a 2008 Suzuki xl-7?


which engine option, you do know belts are not same on all engines right? fact.
2.7L V6 or bigger? IDN.

same on all cars. (answering in generic form do to above)
loosen the tension-er.
take off old
put back new
and if not a spring tension-er,set proper tension
the fSM cover all this.
why not read the manual, RTM?

here is one example (get the book, RTM or see alldata.com)

2008 xl7 engine


Removal Procedure

Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .

Install the engine support fixture. Refer to Engine Support Fixture .

Remove the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

Remove the engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .

Remove the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .

Lower the vehicle


Rotate the drive belt tensioner clockwise to release the drive belt tension.

Slide the drive belt off of the belt idler pulley (1).

Slowly release the drive belt tensioner.

Remove the drive belt from the accessory drive pulleys.

end remove
beg, install



Install the drive belt to the crankshaft pulley, the tensioner and the generator.

Rotate the drive belt tensioner clockwise.

Install the drive belt to the idler pulley (1).

NOTE

Important: Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.

Slowly release the drive belt tensioner.

Raise the vehicle.

Install the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .

Install the engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .

Lower the vehicle.

Install the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

Remove the engine support fixture. Refer to Engine Support Fixture .

Install the the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .
end.

Sep 07, 2014 | 2008 Suzuki XL7

1 Answer

Excercise bike clunking noise


please follow this steps and fix it. God bless you

1

Remove the screws or bolts securing the ends of the pedals to the crank axles. Slide the ends of the pedals off the axles. Remove any screws or bolts securing the left and right disc shields to the base unit. Pull or pry the disc shields off the base unit and set them aside.

2

Remove any screws or bolts securing the left and right side shields to the base unit. Detach the side shields and set them aside. Examine the interior of the base unit and locate the drive belt.

3

Pull the drive belt free of the crank pulley, flywheel and any other pulleys. Discard the old drive belt and install a new belt in its place. Turn the crank axles by hand to confirm that the belt will turn smoothly when the device is in use.Detach the ends of the pedals from the crank axles. Spread a layer of machine grease over the crank axles, then reattach the ends of the pedals.

2

Remove the bolts connecting the pedals to the swing arms. Detach the pedals from the arms, then spread a layer of machine grease over the axles on the swing arms. On some models, the bolts may also serve as the axles. Reattach the pedals to the arms.

3

Remove the bolts connecting the swing arms to the elliptical's upright. Detach the swing arms from the upright, then spread a layer of machine grease over the axles on the upright. Reattach the arms to the upright.

Nov 26, 2013 | Nordic Track Exercise & Fitness

1 Answer

I have a Proform Smart Strider. We just assembled it & when I tested it there's a very loud scraping sound when I stride, regardless of the level or program...help, pls. Thx.


I recomend you to disassemble again, and repeat the steps. Something must be there ARE not according with the instruction assembling. Try however for to see the some loose parts, bolts, nuts, and lube.
See this small instruction.s
God bless you
Remove the screws or bolts securing the ends of the pedals to the crank axles. Slide the ends of the pedals off the axles. Remove any screws or bolts securing the left and right disc shields to the base unit. Pull or pry the disc shields off the base unit and set them aside.

2

Remove any screws or bolts securing the left and right side shields to the base unit. Detach the side shields and set them aside. Examine the interior of the base unit and locate the drive belt.

3

Pull the drive belt free of the crank pulley, flywheel and any other pulleys. Discard the old drive belt and install a new belt in its place. Turn the crank axles by hand to confirm that the belt will turn smoothly when the device is in use.
Lubrication:
Detach the ends of the pedals from the crank axles. Spread a layer of machine grease over the crank axles, then reattach the ends of the pedals.

2

Remove the bolts connecting the pedals to the swing arms. Detach the pedals from the arms, then spread a layer of machine grease over the axles on the swing arms. On some models, the bolts may also serve as the axles. Reattach the pedals to the arms.

3

Remove the bolts connecting the swing arms to the elliptical's upright. Detach the swing arms from the upright, then spread a layer of machine grease over the axles on the upright. Reattach the arms to the upright.

Oct 15, 2013 | Proform Smart Strider SpaceSaver...

1 Answer

Belt falls off


see the next steps and fix it. God bless you
Drive Belt

1

Remove the screws or bolts securing the ends of the pedals to the crank axles. Slide the ends of the pedals off the axles. Remove any screws or bolts securing the left and right disc shields to the base unit. Pull or pry the disc shields off the base unit and set them aside.

2

Remove any screws or bolts securing the left and right side shields to the base unit. Detach the side shields and set them aside. Examine the interior of the base unit and locate the drive belt.

3

Pull the drive belt free of the crank pulley, flywheel and any other pulleys. Discard the old drive belt and install a new belt in its place. Turn the crank axles by hand to confirm that the belt will turn smoothly when the device is in use.

Dec 18, 2012 | Schwinn 150 Upright Bike

1 Answer

The wheel on my elliptical is stuck. A couple steps and it got stuck. How do I fix that?


see this causes and fix it. God bless you
Lubrication

Detach the ends of the pedals from the crank axles. Spread a layer of machine grease over the crank axles, then reattach the ends of the pedals.
2

Remove the bolts connecting the pedals to the swing arms. Detach the pedals from the arms, then spread a layer of machine grease over the axles on the swing arms. On some models, the bolts may also serve as the axles. Reattach the pedals to the arms.
3

Remove the bolts connecting the swing arms to the elliptical's upright. Detach the swing arms from the upright, then spread a layer of machine grease over the axles on the upright. Reattach the arms to the upright.
1 Drive Belt

Remove the screws or bolts securing the ends of the pedals to the crank axles. Slide the ends of the pedals off the axles. Remove any screws or bolts securing the left and right disc shields to the base unit. Pull or pry the disc shields off the base unit and set them aside.
2

Remove any screws or bolts securing the left and right side shields to the base unit. Detach the side shields and set them aside. Examine the interior of the base unit and locate the drive belt.
3

Pull the drive belt free of the crank pulley, flywheel and any other pulleys. Discard the old drive belt and install a new belt in its place. Turn the crank axles by hand to confirm that the belt will turn smoothly when the device is in use.


Oct 14, 2012 | Exercise & Fitness

1 Answer

Older proform crosstrainer ( recumbent bike ) just assembled from box and when I pedal grating sound from pedal area?


1

Remove the screws or bolts securing the ends of the pedals to the crank axles. Slide the ends of the pedals off the axles. Remove any screws or bolts securing the left and right disc shields to the base unit. Pull or pry the disc shields off the base unit and set them aside.

2

Remove any screws or bolts securing the left and right side shields to the base unit. Detach the side shields and set them aside. Examine the interior of the base unit and locate the drive belt.

3

Pull the drive belt free of the crank pulley, flywheel and any other pulleys. Discard the old drive belt and install a new belt in its place. Turn the crank axles by hand to confirm that the belt will turn smoothly when the device is in use.
B) Lubricate your FITNESS BIKE. very important.

Sincerely. Mery Christmas.

Ernesto Cuadra
Managua, Nicaragua.

Dec 24, 2011 | Exercise & Fitness

1 Answer

I have a Nordic Track Commercial 1300 eliptical that started slipping when we used it. We tightened the belt but it didn't help. What else could be wrong?


Step 1

Remove the screws or bolts securing the ends of the pedals to the crank axles. Slide the ends of the pedals off the axles. Remove any screws or bolts securing the left and right disc shields to the base unit. Pull or pry the disc shields off the base unit and set them aside.
Step 2

Remove any screws or bolts securing the left and right side shields to the base unit. Detach the side shields and set them aside. Examine the interior of the base unit and locate the drive belt.
Step 3

Pull the drive belt free of the crank pulley, flywheel and any other pulleys. Discard the old drive belt and install a new belt in its place. Turn the crank axles by hand to confirm that the belt will turn smoothly when the device is in use.

sincerely. Merry Christmas.ernesto cuadra

Dec 18, 2011 | Nordic Track Exercise & Fitness

1 Answer

Belt came off and need to put back on


1

Remove the screws or bolts securing the ends of the pedals to the crank axles. Slide the ends of the pedals off the axles. Remove any screws or bolts securing the left and right disc shields to the base unit. Pull or pry the disc shields off the base unit and set them aside.
2

Remove any screws or bolts securing the left and right side shields to the base unit. Detach the side shields and set them aside. Examine the interior of the base unit and locate the drive belt.
3

Pull the drive belt free of the crank pulley, flywheel and any other pulleys. Discard the old drive belt and install a new belt in its place. Turn the crank axles by hand to confirm that the belt will turn smoothly when the device is in use.

SINCERELY. GOOD LUCK.

ERNESTO CUADRA
MANAGUA,NICARAGUA

Nov 25, 2011 | Proform PFTL79807 - 850 W/ Gamefit...

1 Answer

My Pro-Form 330 elliptical has a resistance problem--it won't adjust and it seems to be set on a difficult resistance, I can't really pedal it. how do I fix this? I tried switching the levels, but...


Detachthe ends of the pedals from the crank axles. Spread a layer of machine greaseover the crank axles, then reattach the ends of the pedals.2
Removethe bolts connecting the pedals to the swing arms. Detach the pedals from thearms, then spread a layer of machine grease over the axles on the swing arms.On some models, the bolts may also serve as the axles. Reattach the pedals tothe arms.3
Removethe bolts connecting the swing arms to the elliptical's upright. Detach theswing arms from the upright, then spread a layer of machine grease over theaxles on the upright. Reattach the arms to the upright.

Oct 27, 2011 | Proform PFTL79807 - 850 W/ Gamefit...

2 Answers

Procedure to replace alternator 2006 mercury mariner 3.0 v6


  1. Disconnect the negative battery cable.
  2. Remove the lower splash shield bolts and the pin-type retainers.
    NOTE The LH lower splash shield must be removed before the RH lower splash shield.
  3. Remove the lower splash shields.
  4. Rotate the front end accessory drive tensioner counterclockwise and position the accessory drive belt aside
  5. Disconnect the alternator electrical connector.
  6. Position the alternator B+ protective cover aside and remove the alternator B+ terminal nut.
  7. Remove the A/C compressor bolts. Use a tie-strap and position A/C compressor aside.
  8. Loosen the alternator nuts.
  9. Remove the lower alternator studs.
  10. Remove the upper alternator bolt and the alternator.

0996b43f80200f35.gif

Feb 18, 2011 | 2006 Mercury Mariner

Not finding what you are looking for?
Bosch SDS-plus BULLDOG Xtreme Rotary Hammer 11255VSR Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Hammering Experts

John Trevino

Level 3 Expert

1388 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

snowycreek

Level 2 Expert

36 Answers

Are you a Bosch Hammering Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...