Question about Panasonic VIERA Televison & Video

1 Answer

I have a Viera TC-P60S30UA. I have the 7 blinking light and replaced all three boards to fix that problem. I plugged it in and heard a loud pop. No smoke or fire. No the tv wont power on at all. I get

I have just had this tv right at a year just past warrenty..large tvs arent cheap its ridiculous that this is such a common problem with this company.

Posted by on

  • Samantha Crouch
    Samantha Crouch Feb 09, 2014

    should have proof read..thats what i get for typing with a 2 year old in my lap..

  • Samantha Crouch
    Samantha Crouch Feb 09, 2014

    Part of my question got cut off. I was also wondering if TC-P60U502 parts would work with TC-P60S30UA model?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Panasonic Master
  • 15,478 Answers

The pop noise was the fuse on the power supply board. You cannot use part substitutions like you are thinking. The only model substitions that you can use are all p60s30XX

Posted on Feb 09, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4090 Answers

SOURCE: loud pop when trying to turn on my samsung

So common its almost criminal! so many sets like this all made in rice paddys. 2000 of them on FIXYA alone.

When fixing electronics it is never the obvious componenent that just needs replacing. If a fuse blows in the house and you replace it only to have it blow again what does that tell you? It wasn;t a faulty fuse!

So in this case it wasn't the resistor that was at fault, it could be any number of components within the circuit and more than likely the IC that was close to this resister and near some capacitors that are also possibly in breach of their acceptable voltage handling. Non of this is DIY for the average joe. If you don't have a service manual or the tools to trace voltage and circuits then leave it to the professional. So many on here jump in doing professional work without really knowing much other thanbeing a board or part jockey and end up costing themselves much more money than having it done propely the first time and without the risk of electrocution, further damage to circuitry that will result in a fire or even a dose of radiation. YOU may have some idea of what you are doing but are you truly knowledgable with electronics?

Better to have the job done properly the first time, Sure there is cudos if you do get it fixed, but looking at the number who come back on here because it failed after a wekk or even the next day It does not seem to be many success stories from what I read everyday

I am sorry for the lecture here, but there are so many who if they took it to a professional would have saved on it rather than ending up paying 3 times the outlay and extra downtime

Thanks for using FIXYA

Posted on Oct 11, 2009

jerryg50
  • 1667 Answers

SOURCE: Viera TH-65PZ850U

Without investigation it is impossible to know what failed. There are a number of boards in that set where there is fairly high current used. It is possible that some components have failed.

The Panasonic service rep would service the set by swapping out the failed modules. If the set is an older model the modules may no longer be available. You can take the set in for an estimate to see if the parts are available, and to see if the set is worth to service.

Jerry G.

Posted on Jan 17, 2009

  • 3 Answers

SOURCE: Blinking red led light when I plug in the tv then it turns right

Phillips purchases the main circuit board from Samsung, and it has a problem with capacitors failing. The failed capacitors can be easily identified as the top will no longer be flat, but will have bulged up.
If you have a local TV repair shop they can help you.

Posted on Aug 10, 2009

SD Tech
  • 14553 Answers

SOURCE: Panasonic Viera 65 inch tv shut off, will not turn back on. Red light blinks 7 times.

Power supply or related to it.

Posted on May 26, 2012

Slinteriors
  • 8617 Answers

SOURCE: no picture and power light blinks 7 times on my viera tc-p50st30 plasma tv when it is turned on

That can be caused by either the SC or SD board. Contact the people at www.tvrepairworld.com they can assist with proper diagnosis and they also should have the replacement board

Posted on Jun 02, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Loud pop, dark screen, three blinking red lights


capacitor in the power unit has blown up.
i hope you have a warranty, if not you can call around see if any one repairs these units, you could call the manufactures customer service line see if the have authorized dealers to service there units.
most of the time the cost of labor and parts it mite be cheaper to buy new one, this depend how old this unit is.
check with the credit card you used, did you buy the extended warranty, where you purchase it will have service provider for that unit.

Oct 06, 2015 | Panasonic TC-P60UT50 60" 1080p 3D Full HD...

1 Answer

How do you replace a fuse on the 2011 Panasonic TC-P55VT30 plasma TV?


gently lie it facedown and unscrew the back to reveal the boards and fuses

Jul 28, 2015 | Panasonic TCP55VT30 55" VIERA 3D HD Plasma...

1 Answer

Viera tc-p50ut50 light blinking eight times


One the circuits popped. you can locate the bad board and replace. Use these charts to help locate the problem.
d8cc4a6e-4ee4-4017-8f29-c4c8065eceb0.jpg6d3cda0a-fc21-4798-8c48-961614410ad8.jpg

Apr 11, 2013 | Panasonic TCP50UT50 Smart Viera 50 Class...

1 Answer

Panasonic Plasma TC-P50G10, Loud pop. No picture or sound. 6 blinking lights Took back off and nothing evident. What could have made such a loud noice. I expected to look up and see the who tv...


you need to look closely with a flashlight. there is a circuit that popped and you'll see one of the black circuits that is connected to the heat sink that looks different from the others. 2_8_2013_2_04_20_am.jpg

Jan 31, 2013 | Panasonic Viera TC-P50G10

1 Answer

Panasonic Viera tc-p65s2 - 7 blinks, won't turn on


I had the same problem with my Viera. if you disconnect the power and ribbon cable from the YSUS board (check youtube for how), the light led will blink 6 times, indicating the YSUS is bad. Check ebay for TNPA5175 board (about $115-160). The pop is one of the DG402RP chips burnout. These are about $4, but only available from China. If you can wait a month for delivery, you can solder the new one to replace the bad one. You may want to purchase several in case more are bad or it happens again.

Aug 06, 2012 | Panasonic VIERA Televison & Video

1 Answer

I have replaced the p board and sc boards in this panasonic tc-p50s30 viera tv and still have the 7 red blinks? what else can be wrong?


7 blinks is indicate for faulty power supply however if you already replace it the possible problem is on main board..

Jun 06, 2012 | Televison & Video

1 Answer

No picture and power light blinks 7 times on my viera tc-p50st30 plasma tv when it is turned on


That can be caused by either the SC or SD board. Contact the people at www.tvrepairworld.com they can assist with proper diagnosis and they also should have the replacement board

Jun 01, 2012 | Panasonic VIERA TC-P50ST30 50-Inch 1080p...

1 Answer

WHILE WATCHING MY TV TONIGHT I HEARD A LOUD POP AND NOW NO PICTURE JUST BLINKING RED LIGHT


10 blinks for this tv is not always an A Board issue. It can be a problem with the power board as well. A technician should look at the set to dertermine where the problem lies otherwise it is just a guessing game of inni minni miny moe.

Apr 03, 2011 | Panasonic TC-P50S1 50 in. Plasma LCD HDTV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Televison & Video Experts

 Grubhead
Grubhead

Level 3 Expert

5017 Answers

The Knight
The Knight

Level 3 Expert

73647 Answers

Jaime Hernandez

Level 3 Expert

2315 Answers

Are you a Panasonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...