Question about Zanussi F1045W Front Load Washer

1 Answer

Zanussi 1200 essential washing machine, cleaned out filter now will not fill with water

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 46 Answers

Go back into the machine and check for a disconnected wire cause by cleaning out the filter. Oh and did you remember to turn the water faucet back to the on position? It helps to plug the machine in to the A/C outlet, too. Keep an eye attuned to a safety switch on the access panel as well. It may have an alignment or broken plastic fastening/ mounting design.

Posted on Feb 08, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 8 Answers

SOURCE: zanussi turbo dry 1200

Try cleaning out the pump, and main hose to sump. If problem persists replace pump.


Slim Jim

Posted on Nov 26, 2007

kjmac
  • 97 Answers

SOURCE: Zanussi FC1200W

have you checked the filter behind the flap on the front of the machine, this could be blocked. if the machine is full of water though you will have to manually drain it by putting the grey outlet hose into a bucket or a washing up bowl. you will also need one or two towels to place on the floor because there wil still be a bit of water left in the ipes even though the drum is empty.

hope this helps

Posted on Jul 28, 2008

  • 8 Answers

SOURCE: my zanussi essential washing machine

Sounds like the inlet valve is faulty, though this should not effect the wash. Does it spin?

Posted on Jan 11, 2011

  • 1 Answer

SOURCE: My Zanussi Aquacycle 1200 Frontloader (F1225)

my washing machine wont work it only drains

Posted on Jan 24, 2011

  • 196 Answers

SOURCE: have a Zanussi electrolux essential 1200 washing

Sounds like the Tachometer on the motor is faulty, this is the built in revolution counter that controls the speed of the motor, unfortunately it means the motor needs replaced and they can be expensive, about half the price of the machine. But if you want to change it then it is quite simple, just 2 or 4 screws hold it in place and the plug an belt just pull off. Hope this helps.

Posted on Feb 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The conditioner isn't going through my machine


Clean conditioner compartment as you can see on bottom picture.
Be sure to read the instructions of the manufacturer of conditioner. Some manufacturers supply concentrated softener which should be diluted with water (is too dense and can clog small drain tube in softener compartment). Also make sure you do not fill up over sign MAX., otherwise softener may leak in drum before starting the washing machine.

Dado

25206924-flqkugifsqcdnw3unlwetsmc-5-2.jpg

Oct 10, 2014 | Zanussi Washing Machines

1 Answer

Zanussi 1200 6kg, not spinning or taking in water ?


Try unplugging the unit for 30 mins. then run it again.

Nov 21, 2012 | Washing Machines

1 Answer

I have a Zanussi 1200 fj 1254 when I turn on the machine and it starts to fill with water...water starts to pour out of the fluff filter mechanism never mind how tight we try to do it up ... any ideas ??


Hi from retired Englishman in SW France,

I suspect there is either limescale in the thread of the filter plug OR behind the filter itself and this is stopping the plug from being screwed home completely. Remove the plug, pull out the filter, clean filter compartment all round, especially at the back AND ensure the plug thread is completely free of limescale ;-0)

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

Sep 09, 2011 | Zanussi FJ1254W Front Load Washer

2 Answers

Missing user manual for Zanussi Essential 1200


I have downloaded a manual for the item

May 17, 2009 | Washing Machines

1 Answer

Jetstream 1200 wont take away fabric softner


strip and clean out the soap tray then remove the tray and clean the fill water holes above it with a stiff washing up brush.

Mar 16, 2009 | Zanussi ZWF1430W Front Load Washer

2 Answers

Zanussi FC1200W


have you checked the filter behind the flap on the front of the machine, this could be blocked. if the machine is full of water though you will have to manually drain it by putting the grey outlet hose into a bucket or a washing up bowl. you will also need one or two towels to place on the floor because there wil still be a bit of water left in the ipes even though the drum is empty.

hope this helps

Jul 28, 2008 | Zanussi FC1200W Front Load Washer

1 Answer

Zanussi turbo dry 1200


Try cleaning out the pump, and main hose to sump. If problem persists replace pump.


Slim Jim

Nov 12, 2007 | Zanussi FJS1225W Front Load Washer

Not finding what you are looking for?
Zanussi F1045W Front Load Washer Logo

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

shaun taylor

Level 3 Expert

1525 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...