Question about Zanussi FJS1225W Front Load Washer

1 Answer

New module fitted but not working

I've replaced the module on my washing machine(the old one had burn marks on it!)but when i tuned it back on it just keeps beeping

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Contributor
  • 54 Answers
Re: New module fitted but not working

This module will need to be set up in a binary code by a zan eng

Posted on Feb 14, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Unit is dead after experiencing "open neutral" situation at campground.

Just went through the same problem. After removing back cover I noticed surge protecter had some burn marks. I called Westland Sales ordered a new one (about $70). Still didnt fix but it was toast. Investigated further & noticed module board had obvious burn marks. Called Westland again fearing it would be cheaper to replace but board was about $350. For a total of around $450 its good as new. Only basic tools & knowledge required. Phillips screwdriver, 1/2" wrench & a small allen wrench (5/32") if I remeber correctly. I found it easier to replace parts with machine face down & removed bottom cover. Labor time for me was about 20 mins including removing parts & both covers.

Oct 15, 2012 | Splendide 2100XC

1 Answer

I have an F&P MW612 washing machine that stops at the start of the spin cycle leaving water in the machine. After pushing the pause button, looking inside, closing the lid and restarting I've heard...

Something may have been stuck in the drain pump impeller creating the clanking noise. This is a serious problem that can lead to the burning out of the motor controller module, the machine's "brain". It has been found that a short circuit is imminent on a leaky drain pump which can eventually burn out the motor controller module.

Empty the machine then lay it's front on a padded floor/surface and check the drain pump including the diverter valve where both the drain pump and the recirculation pump connect from. Replace the drain pump if damaged or leaking to avoid further damage to the motor controller module.

Fault Code Reading on Fisher and Paykel Top Load Washing Machines

Aug 23, 2011 | Washing Machines

1 Answer

I have a Maytag topload 1412 series 4. I recently tried to wash a comforter far too big for it. About ten minutes into the first cycle I checked on it and smelled something burning. I did not see any...

lo mas combeniente en estos casos es revisar el bobinado del motor obiamente esta quemado pero puede ser renplasado por un motor nuebo instalado por un experto en la materia

Oct 05, 2010 | Maytag PAV2300 Top Load Washer

1 Answer

The plug on my 6 year old Zannusi washing machine has just burnt out. Is it safe to replace it and try again?

No it would not be safe to fit a new plug and try again. If the plug burned out it would appear that there's a short circuit somewhere in the machine possibly caused by a leak. If you replace the plug you risk burning down the house or electrocuting yourself. I'd advise you to get a repairs man to check out the machine to see if it's repairable. It could be something as simple as needing a new door seal which would cost you around 30 euros.

Aug 31, 2010 | Washing Machines

1 Answer

10 year old miele 300 washing machine jumps to

Most likely brushes. Fit carbon brushes part no.4297411 as they are less then half the price of the brush module Part no. 4229779.

Jun 15, 2010 | Miele 300 Front Load Washer

2 Answers

Fisher & Paykel Washing Machine WL80T65CW1 Fault 9

sounds like a size error . when you changed the display did you size your machine to the new display module?did you get the re-size set of instructions with the new display board? ring up where you brought the display from and i"m sure they can help. if not reply back and i will guide you thru it.

May 26, 2010 | Washing Machines

1 Answer

I need to unplug it and then plug it back in before it will turn on.

its the same old story with this type of machine you need a new module can cost anything from £70 to £150 to buy then a fitting charge

Mar 26, 2010 | LG WM-1832C Front Load Washer

1 Answer

Hotpoint Aquarius 900 WM61, washed but stopped spinning, about 6 wks ago, new brushes fitted old 1's had split everything worked fine, 6 wks down the line machine washes but doesn't spin again, bushes are...

hello carl check the module circuit board this controls the speed check the transistor on the boards for dry joints if discoloured change the board all the best


Aug 04, 2009 | Washing Machines

1 Answer

Washer doesnt fill water but goes thru all cycles

After contemplating the issue, I decided that the machine "thought" it had filled. That led me to believe that the water level control was not working. I happened to have a control from an old washer that I could make fit. After replacing this control, I'm back in business. Everything is working fine although I now have only 3 water levels to chose from where I previously had 5. I hope this helps. Good luck. Mark

Dec 26, 2008 | Washing Machines

1 Answer

Bosch WFL 2462

Your exit hose behind the machine has to go over a certain height before it goes into your wall standpipe or sink. The height is marked behind your machine, approx 3 feet above ground level. The hose should put about 3 or 4 inches into the standpipe, & not fitted airtight.

Possible u didnt connect well after your pump job or ........

May 02, 2008 | Bosch Classixx WFL 2462 Front Load Washer

Not finding what you are looking for?
Zanussi FJS1225W Front Load Washer Logo

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides