Question about Verbatim ® Store `n` Go USB Flash Drive, 8GB

Open Question

My USB flash drive is not recognizable in any computer. It will give me a couple of codes..... Currently, this hardware device is not connected to the computer. (Code 45) or Windows has stopped this

It shows up in device manager as unknown device. But in "My Computer" the drive does not show up at all. There is no light that is blinking or turning on when I plug it in. I have tried it in multiple desktops and a couple of laptops, various different ports. The message that comes up is "Windows has stopped this device because it has reported problems. (Code 43)." In Device Manager, the yellow exclamation point shows up and I've tried uninstalling it and then scanning for new hardware. It comes back with the yellow exclamation. I've pulled out the battery of my laptop, waited 30 minutes, and turned it back on. I've updated drivers and it says "The best driver for my device is already installed." Even though, when I first plug it in the usb port is will tell me that the "Device Driver Software was not successfully installed." I've checked on the verbatim website and there are no drivers that I can install manually. My computer has been updated with all the needed updates. I just need to open it long enough to copy the files onto my computer. Is there any way to override the windows stopping the device? This was the replacement Verbatim store n go 8G that has done this same thing. I have MONTHS of work on this drive and I would like to be able to recover it. Thank you in advance!

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5089 Answers

SOURCE: USB port is not recognized in any of my computers or in any port.

Google search how to reformat flash drive.
I had same problem with external hard drive and reformatted, and all data was intact.
Then back up on cloud, or separate drive

Gene

Posted on Feb 10, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

USB port is not recognized in any of my computers or in any port.


It seems that the issue is related with the flash drive itself, I have came across with such problems many times. I guess now it's time you should go and ask for a replacement.Most of the flash drives comes with 5 years warranty. You may want to call verbatim customer support for warranty. Contact details
http://www.verbatim.com.sg/en_SG/contact-us

Feb 07, 2014 | Verbatim ® Store `n` Go USB Flash Drive,...

1 Answer

My USB flash drive is not recognizable in any computer. It shows up in device manager as unknown device. But in "My Computer" the drive does not show up at all. There is no light that is blinking o


Download the driver from Verbatims web site. Reinstall it some of thos flash drives are really picky. You might have had a virus and it wrecked the connection. Reinstall the driver from Verbatim.

Feb 07, 2014 | Iomega 34610 320 GB USB 2.0 Hard Drive

1 Answer

Currently, this hardware device is not connected to the computer. (Code 45)Currently, this hardware device is not connected to the computer. (Code 45)


Pls send the brand/model.

In general the case could be that USB port does not recognize the USB camera. Usually this is a Windows problem and not a HW or camera problem.

Try using an intermediate USB port before connecting the camera.
This trick will make windows see the camera (in 90% of the cases)

There are many cheap ones available like:
http://www.ebay.com/sch/i.html?_sop=15&_sacat=0&_from=R40&_nkw=usb+hub&rt=nc&LH_BIN=1

Nov 20, 2012 | Computers & Internet

1 Answer

Verbatim store n go usb flash drive 8 gb device not recognized


My Verbatim Sto N Go 8GB USB Flash Drive does not work in any port, in any computer. When I plug it in, the "Device is not recognized" error comes up. When I click on it, and the Unknown Device Properties comes up, the device status reads: "Currently, this hardware device is not connected to the computer. (Code 45)

To fix this problem, reconnect this hardware device to the computer."



The driver details read:
Provider: Advanced Micro Devices
File Version: 1.0.11.82 built by: WinDDK
Digital Signer: Microsoft Windows Hardware Compatibility


This is the 2nd drive of this same brand that quit working within 6 months. I have MONTHS of work on files in this drive, and would hate to have to redo all that work! I was real careful after the first one went bad to use the eject button when removing it from my computer. But I am thinking the last time I clicked the eject button, it froze, so I just pulled it out without the message coming up. Hopefully there is someway to get the computer to recognize this drive again???

Sep 26, 2012 | Verbatim ® Store `n` Go USB Flash Drive,...

1 Answer

Problem for Transcend 4GB JetFlash 110 USB 2.0 Flash Drive My pen drive gets heated up and not recognised by computer. what can i do. pl. help


when i plug in my TRANSCEND 4GB USB DRIVE,i got the connecting tone,connecting msg(found new hardware:mass storage device And finnaly problem occured during hardware installation,your new hardware might not work properly).ssuppose if i unplug it i can hear the removing tone.PLs help me to resolve this.........

Aug 24, 2010 | Transcend 4GB JetFlash 110 USB 2.0 Flash...

2 Answers

I've tried to put things on my usb but whenever i put it in a computer they all say that it doesn't recognize the hardware


All Portable HD are Plug and play devises. But sometimes they require softwares. So read your manual for further details.
Think this is helpful !

Aug 11, 2010 | Dane-Elec DaneElec 4GB USB Drive Copper...

2 Answers

My PC will not recognize PNY USB 2.0 4G drive. It is not in My Computer folder either.


One or more of the hints below will probably sort out most USB problems with most USB portable / external hard drives and OTHER devices (though not always)

A few things to check but assumes
USB and Windows for other interfaces / operating systems (mac/ Linux) similar steps may be adapted to suit.

1. Ensure it is connected directly to the computer to a
USB 2.0 port not a USB 1.0 port as this can have effects on performance and reliability

2. Use only the cables that came with it NOT one that fits that may have been lying around or is longer. Not all
USB cables are equal even though they should be)

3. Do not connect through an external
USB HUB unless that hub is USB 2.0 AND has its own power supply.

4. Use ONLY the power supply that came with it if it has an external power supply Don’t use any other unless you know it has both the same voltage and current rating e.g. 12V 500mA anything rated below that would not work properly.

5. Always use the same port for connecting your devices. Some devices do not like being switched about. If switched they may want to install software / drivers again. This can be especially true if you move a HUB to another port


6. For FLASH DRIVES you should ensure that the device is set for "quick removal" using the drive control panel properties or use the
USB "Safely Remove Hardware" option. If you don’t do this there is a very strong chance that any files you transfer may not be there when you plug into another computer.


7. It is possible to remove drives from the enclosures in most cases and connect directly inside a PC to fully check it.
You should also do this to check the drives connections are not bad inside the enclosure.


8. If none of the above steps help look at updating the drivers from the manufacturers web site in the support section.

9. If you checked and fixed anything there and still have issues then check your hardware from CONTROL PANEL / SYSTEM / HARDWARE.
Any exclamation marks by hardware need fixing before you investigate any further


10. Ensure that you have set removable drives for "quick removal" or that you use the "Safely Remove Hardware" option often shown on the lower toolbar. It is possible that files my not be fully written to external devices before they are removed. This corrupts the file itself and even on occasion the drive.
SPECIAL NOTES
USB flash drives can fail for no apparent reason.
Sandisk Cruzers are especially bad for this.

USB hard drives should be treated with extreme care.
This is a real hard drive ! And knocks and bumps can quite literally kill them.

Note that if you hear a drive clicking or pinging this could be the worst thing you would hear.
Known as "The Click of Death"

Hope this gives you the information you need

Apr 14, 2010 | PNY 4GB USB 2.0 Flash Drive - Grey/Black

2 Answers

My flash drive will not operate when plug into my lap top.


Hello kjh87....
1) If you are using a USB cable with your device, check the cable to make sure it matches the speed of the device. Use USB 2.0 cables with USB 2.0 devices and USB 1.1 cables with USB 1.1 devices. Swap cables and check the device, if this does not work, proceed to Step 2.
2) Next, open Device Manager and look under the heading for USB Serial Bus Controllers. If there is a device with a yellow exclamation mark next to it such as USB Mass Storage Device. Double-click on the entry and check the Device Status. If the status shows something like
"This device cannot start. (Code 10)"
proceed to Step 3.
3) The easiest way to solve a USB error code 10 in Windows XP
is to follow the steps below to remove and reinstall all USB controllers.
A. Click on Start
B. Right Click on My Computer, click on Properties
C.Click on the Hardware tab
D. Click the Device Manager button.
E. Expand Universal Serial Bus controllers section.
F. Right-click every device under the Universal Serial Bus controllers node, and then click Uninstall to remove them one at a time.
G. Restart the computer, and allow the computer to reinstall the USB controllers.
H. Plug in the removable USB storage device, and then test to make sure that the issue is resolved.
For more information on Troubleshooting USB device problems, visit the Microsoft Support Article on this subject.

I hope this helps...

May 28, 2009 | SanDisk Cruzer Micro 8GB USB 2.0 Flash...

1 Answer

Cruzer micro 2.0GB does not work anymore, it started flashing and then it stopped. When connected to USB port the computer does not start and when connected afterwards the device is not recognized by the...


Some times it happens that Windows explore do not recognise the USB flash drives. There may be some causes: 1. Ckheck your flash drive & ensure that it was not burnt or have any physical damage. 2. Start the computer without flash drive and connect the flash drive to it. Noe ensure that your computer is not hanged.If your computer hanged than the flash drive is damaged. 3. if your computer is not hanged and not dectecting the drive,(fore windows) go to My computer, right click, properties, divice manager. In the device list see USB serial bus controllers. click + next to it to see the sub devices. 4. Now see that the computer has a listing for the flash drive. The listing may be as "Usb mass storage device", "Drive company name: etc. 5. If there is listing no listing for flash drive just disconnect it and see the device manager listing. some changes will occur or mouse pointer will show busy. Again reconnect the flash drive the same thing happens. 6. if your flash drive worked as in step 5 that means the the drive is ok and the compueter is ok. There is prblem with driver of flash drive that is currently installed. Please upgrade the driver from your flash drive manufacturer or it is ready to use device just unuinstall it from the device manager listing. Restart the computer. after restart connect the flash drive it will detect the drive. 7. if there is still a problem go to start run & type regedit and press enter to run registry editor. In Hkey_local_machine>software>Cruzer micro and delete it. restart the computer. 8. You wrote that if you connect it to USB port computer does not start. If above step 1 to 7 does not work means there is strong possibality of reading problem means the flash drive has errors on it and file system is damaged. This same thing happens with Cd drive with a cd having corroupt file system. i will prefer to take the flah drive to an local hardware expert or manufacturere.

Jul 23, 2007 | SanDisk 2GB Cruzer Micro SDCZ62048A10 Hard...

7 Answers

Error code 10


wow i think i solved it by just giving your mom the Alabama Hot Pocket while i licked your sister. that seemed to work pretty well.

Nov 03, 2006 | LaCie d2 Extreme 250GB External with...

Not finding what you are looking for?
Verbatim ® Store `n` Go USB Flash Drive, 8GB Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Verbatim Office Equipment & Supplies Experts

Computer Links

Level 3 Expert

2385 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

k24674

Level 3 Expert

7993 Answers

Are you a Verbatim Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...