Question about Xerox Phaser 7300DN Laser Printer

1 Answer

Does not recognize second tray

We just picked up a Xerox phaser 7300.  Machine does not recognize that second tray is installed.  Reseated all the board connections on second unit.  No luck.  Any ideas would be appreciated.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Is it not recognizing the second tray from the print driver or from the configuration page that prints

Posted on Dec 06, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Help with u2 code on phaser 7300


U2 is an engine EEPROM failure - you'll need to replace the main board to fix that, I'm afraid.

Jan 08, 2013 | Xerox Phaser 7300DN Laser Printer

1 Answer

I have a Xerox phaser 7300 that keeps telling me to install or reseat the black cartridge


It is slightly unusual for it to be the black toner cartridge (usually cyan or magenta) but this issue is quite common on the 7300. You can find a lot of information about this here.

Dec 15, 2010 | Xerox Phaser 7300DN Laser Printer

1 Answer

Colors do not align


Apparently, turning the unit off for 30 seconds, then back on will force the Phaser 7300 to do a color alignment procedure (according to Xerox support).

Then, if the problem persists, you are instructed to follow a very detailed troubleshooting procedure which I will leave with you in the following link:

Xerox Phaser 7300 Misregistration Issues

I hope this helps!

Nov 03, 2010 | Xerox Phaser 7300DN Laser Printer

1 Answer

I have a phaser 7300 that asks for a transfer unit about every 3 weeks. It prints good until it asks for unit and then it will not print until I install a new one. I am ready to install the 4th unit but...


I think you might have a Spring missing for the Waste Toner Full Sensor. The machine tolerates the sensor status for 2K pages and then shuts it down.

Truthfully, it is really hard to describe in a few sentences. It belongs in the frame wall under near where you have the white waste toner section of the Transfer Belt. This spring pushes a flag up that hits the Paper Entrance Sensor (yes, near the bypass tray)

The PN for the spring is 116-2050-00.

Whit
Item, Inc.

May 21, 2010 | Xerox Phaser 7300DN Laser Printer

2 Answers

Xerox Phaser 7300 color misregistration


Apparently, turning the unit off for 30 seconds, then back on will force the Phaser 7300 to do a color alignment procedure (according to Xerox support).

Then, if the problem persists, you are instructed to follow a very detailed troubleshooting procedure which I will leave with you in the following link:

Xerox Phaser 7300 Misregistration Issues

I hope this helps!

Mar 15, 2010 | Xerox Phaser 7300DN Laser Printer

1 Answer

Phaser 7300 jamming manual feed


Can you print fine with no jams from the lower tray?
make sure you have clean new paper and start out with the 11"x8.5' letter paper. If you have that then follow the instructions below.

  1. Make sure there is no peaces of paper jammed in the path.
  2. clean the rollers with regular rubbing alcohol sometimes the rollers get way dirty to pick up the paper.
  3. If none of these tricks helped you then you have to change the the manuel feeder. part # 116-1561-00 good luck.

Dec 07, 2009 | Xerox Phaser 7300DN Laser Printer

2 Answers

Phaser 7300 Error Code/Message


Seems to be something to do with the Ram.

More help HERE

Jun 01, 2008 | Xerox Phaser 7300DN Laser Printer

1 Answer

Error message


Cause:
This message is related to the on-board SRAM on the Print Engine Control Board Solution: thumbsup.gif Fixed! thumbsdn.gif Did not fix. Replaced the Print Engine Control Board,

Dec 19, 2007 | Xerox Phaser 7300DN Laser Printer

Not finding what you are looking for?
Xerox Phaser 7300DN Laser Printer Logo

Related Topics:

254 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Office Equipment & Supplies Experts

Michel

Level 2 Expert

97 Answers

Philip Hughes

Level 2 Expert

75 Answers

docukaaf

Level 1 Expert

25 Answers

Are you a Xerox Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...