B181F7BB reference code

This warning indicator is controlled by the BCM - body control module . You cant turn it off , you need to fix the faulty input switch that signals the BCM that the door is open .
Body Control Module
The various body control module (BCM) input and output circuits are described in the corresponding functional areas indicated on the BCM electrical schematics. The BCM functions include the following:
• Battery rundown protection--Inadvertent power--Refer to Interior Lighting Systems Description and Operation in Lighting Systems.
• BTSI/automatic transmission shift lock control--Refer to Automatic Transmission Shift Lock Control Description and Operation in Automatic Transaxle - 4T65-E.
• Bulb check--Refer to Instrument Cluster Description and Operation in Instrument Panel, Gages, and Console.
• Chimes--Refer to Audible Warnings Description and Operation in Instrument Panel, Gages, and Console.
- Check gages
- Content theft deterrent
- Door ajar warning
- Headlamps ON
- Key-in-ignition
- Oil reset
- Park brake warning
- Seat belt not fastened
- Turn signal ON
- Vehicle theft deterrent
• Door lock interface--Refer to Power Door Locks Description and Operation in Doors.
• Exterior and interior lighting control--Refer to Exterior Lighting Systems Description and Operation in Lighting Systems.
- Automatic lighting control
- Backup lamps
- Daytime running lights (DRL)
- Fog lamps
- High/low beam head lamps
- Park brake lights
- Turn hazard lamps
• Gage control--Refer to Instrument Cluster Description and Operation in Instrument Panel, Gages, and Console.
• Heated seats--Refer to Heated Seats Description and Operation in Seats.
• Horn interface--Refer to Horns System Description and Operation in Horns.
• Instrument cluster indicator control--Refer to Instrument Cluster Description and Operation in Instrument Panel, Gages, and Console.
• Interior lighting--Refer to Interior Lighting Systems Description and Operation in Lighting Systems.
• Key-in-ignition sensing--Refer to Audible Warnings Description and Operation in Instrument Panel, Gages, and Console.
• Parking brake state sensing--Refer to Brake Warning System Description and Operation in Hydraulic Brakes.
• Retained accessory power (RAP)--Refer to Retained Accessory Power (RAP) Description and Operation in Retained Accessory Power.
• Rear compartment interface--Refer to Power Door Locks Description and Operation in Doors.
• Rear defogger--Refer to Rear Window Defogger Description and Operation in Stationary Windows.
• Remote function control--Refer to Keyless Entry System Description and Operation in Keyless Entry.
• RFA communication link--Refer to Keyless Entry System Description and Operation in Keyless Entry.
• Seat belt use sensing--Refer to Seat Belt System Description and Operation in Seat Belts.
• Theft deterrent vehicle/content--Refer to Theft Systems Description and Operation in Theft Deterrent.
• Washer solvent level sensing--Refer to Wiper/Washer System Description and Operation in Wipers/Washer Systems.
• Wiper/washer--Refer to Wiper/Washer System Description and Operation in Wipers/Washer Systems.

As far as the sliding doors , pull the fuse's

Door ajar switch problem more then likely or wiring issue . The BCM - body control module won't turn off interior light , let door lock because it think's the door is open . The door ajar switch is a input to the BCM .

The first thing would be to have it checked for DTC'S - diagnostic trouble codes . Also check with an enhanced scan tool to see if the BCM shows ajar switch data (open or closed ? Do you know about body electronics ?
Body Control Module
The various BCM input and output circuits are described in the corresponding functional areas indicated on the BCM electrical schematics. The Body Control Module functions include the following:
?€¢
A/C compressor request. Refer to Air Temperature Description and Operation

?€¢
Remote Function Control. Refer to Keyless Entry System Description and Operation

?€¢
A/C cooling Fan. Refer to Air Delivery Description and Operation

?€¢
Audio Delay Power. Refer to Radio/Audio System Description and Operation

?€¢
Exterior and interior lighting control. Refer to Exterior Lighting Systems Description and Operation

-
Daytime running lights (DRL)

-
Automatic lighting control

-
Fog lamps

?€¢
Interior lighting. Refer to Interior Lighting Systems Description and Operation

?€¢
Battery rundown protection (Inadvertent Power). Refer to Interior Lighting Systems Description and Operation

?€¢
Chimes. Refer to Audible Warnings Description and Operation

-
Key-In-Ignition

-
Head Lamps On

-
Seat Belt Not Fastened

-
Turn Signal On

-
Park Brake Warning

-
Door Ajar Warning

-
Check gages

?€¢
Gage control. Refer to Instrument Cluster Description and Operation in Instrument Panel, Gages, and Console.

?€¢
Instrument cluster indicator control. Refer to Instrument Cluster Description and Operation in Instrument Panel, Gages, and Console.

?€¢
Theft deterrent. Refer to Theft Systems Description and Operation .

?€¢
Engine coolant level sensing. Refer to Cooling System Description and Operation .

?€¢
Washer solvent level sensing. Refer to Wiper/Washer System Description and Operation in Wipers/Washer Systems.

?€¢
Key-in-ignition sensing. Refer to Audible Warnings Description and Operation in Instrument Panel, Gages, and Console.

?€¢
Seat belt use sensing. Refer to Seat Belt System Description and Operation .

?€¢
Brake fluid level sensing.

?€¢
Parking brake state sensing.

?€¢
Rear compartment interface. Refer to Power Door Locks Description and Operation

?€¢
Horn interface.

?€¢
Door lock interface. Refer to Power Door Locks Description and Operation

?€¢
Bulb Check. Refer to Instrument Cluster Description and Operation in Instrument Panel, Gages, and Console.

You have no idea what your messing with . Theft light on , DTC'S - diagnostic trouble codes stored . Before you start replacing BCM an making matters worse ,do yourself a favor an take it to a qualified repair shop .
The powertrain control module (PCM) communicates with the instrument cluster using serial data over the UART serial data bus, CKT 800. When the instrument cluster determines a Pass Theft condition, the instrument cluster sends a coded password to the PCM. When the instrument cluster receives the correct password, the PCM enables the fuel injection system in order to allow the vehicle to operate normally. The PCM may allow the vehicle to start and stall quickly during a failed theft condition.

The Passlock™ lock cylinder is a locking cylinder that turns a rotating magnet past a stationary hall effect sensor. The rotating magnet creates a resistance code (R-Code) that the cylinder sends to the instrument cluster. The Passlock™ lock cylinder interfaces with the instrument cluster through a 3 wire connection. The 3 wires have the following functions:
• Power
• Ground
• Data
The THEFT SYSTEM indicator will not light under any circumstances.
Replace the instrument cluster.
For Chevrolet vehicles, refer to Instrument Cluster Replacement .
For Pontiac vehicles, refer to Instrument Cluster Replacement .
Multiple indicators light continuously.
Test for a loss of serial data. Refer to Data Link Communications System Check .
Instrument cluster DTC B1021 sets.
The DTC indicates a loss of powertrain control module (PCM) serial data. Refer to Data Link Communications System Check .
Instrument cluster DTC B1022 sets.
The DTC indicates a loss of SIR serial data. Refer to Data Link Communications System Check .
Instrument cluster DTC B1023 sets.
The DTC indicates a loss of ABS serial data. Refer to Data Link Communications System Check .
Instrument cluster DTC B1011 sets.
Refer to DTC B1011 Passlock Cyl Data Shorted This Ign Cycle in Instrument Panel, Gauges and Console.
Instrument cluster DTC B1012 sets.
Refer to DTC B1012 Passlock Bad R-code This Ignition Cycle in Instrument Panel, Gauges and Console.
Instrument cluster DTC B1013 sets.
Refer to DTC B1013 Passlock Bad Timing This Ignition Cycle in Instrument Panel, Gauges and Console.
Instrument cluster DTC B1014 sets.
Refer to DTC B1014 Passlock R-code Unprogrammed in Instrument Panel, Gauges and Console.
Instrument cluster DTC B1015 sets.
Refer to DTC B1015 Passlock Cluster Fail Enabled in Instrument Panel, Gauges and Console.
Instrument cluster DTC B1017 sets.
Refer to DTC B1017 Passlock R-code Learn Failed in Instrument Panel, Gauges and Console.
The indicator flashes and no instrument cluster codes are set.
Refer to DTC B1013 Passlock Bad Timing This Ignition Cycle in Instrument Panel, Gauges and Console.
So , do yourself a favor an have a qualified repair shop check it out .

How does the vehicle run ?
Malfunction Indicator Lamp (MIL) Always On
Circuit Description
Ignition voltage is supplied to the malfunction indicator lamp (MIL). The powertrain control module (PCM) turns the MIL ON by grounding the MIL control circuit.
MIL Operation
The MIL is located on the instrument panel (IPC).
MIL Function ?€¢
The MIL informs the driver that a malfunction has occurred and the vehicle should be taken in for service as soon as possible.

?€¢
The MIL illuminates during a bulb test and a system test.

?€¢
A DTC will be stored if a MIL is requested by the diagnostic.

You could have a bad instrument cluster ! Here is part of diagnostic flow chart for your vehicle !

1

Did you perform the Diagnostic System Check-Engine Controls?
Go to Step 2
Go to Diagnostic System Check - Engine Controls

2

1. Turn OFF the ignition.
2. Disconnect the PCM.
3. Turn ON the ignition, with the engine OFF.
4. Observe the MIL.

Is the MIL illuminated?
Go to Step 3
Go to Step 5

3

1. Remove the instrument panel cluster (IPC). Refer to Instrument Cluster Replacement in Instrument Panel, Gages, and Console.
2. Test the MIL control circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?
Go to Step 6
Go to Step 4

4

Replace the IPC. Refer to Instrument Cluster Replacement in Instrument Panel, Gages, and Console.
Did you complete the replacement?
Go to Step 6

5

Replace the PCM. Refer to Powertrain Control Module Replacement .
Did you complete the replacement?
Go to Step 6

code p0016refers to the crankshaft /cam shaft position sensor bank 1 sensor A-- correlation===causes---Wiring CKP sensor--CMP sensor--mechanical fault Check timing belt is not broken
code po113 refers to intake air temp (IAT) sensor--circuit malfunction===causes ---wiring open circuit/short to positive--wiring short to ground---ground wire defective IAT sensor---ECM
code mp0700 refers to transmission control system/MIL-malfunction===causes--wiring ---TCM
code po562 refers to system voltage low==causes---wiring poor connections---battery---alternator or it also refers to ECM power relay control--circuit open===causes ---wiring--ECM ---relay. For this one check the battery terminals and posts are shiny clean and tight . Have a load test done on the battery to check for faulty cell. check condition of alternator drive belt and check alternator out put.

"te" error code is caused by a faulty thermistor; likey cause is:
a. Loose wiring at the control panel (directly behind the cycle selector knob)
b. Broken wire at the thermistor (located at the bottom/front of the tub)

To access the wire plug connectors at the control pannel, remove the top cover of the washer. Stand in front of the washer and look for the plug connectors behind the control panel. Pull apart the plugs and re-install.

Test the washer. If the "te" error still occurs it will be neccesary to remove the front panel as well (two sets of special plier-type tools are needed).

Inspect the thermistor closely, with good lighting. If there's a break in the wire it will be at or near the black sheathing / heat shrink material.

Just like a reference guide, this service manual could helpful: MAH9700AW

Hope this helps.

iseries uses EBCDIC and the file is probably ASCII when importing from/to the iSeries charset convertions ensues, there must be some char that isn't translating well and thus converting itself in some control code, use DSPF or EDTF to open the file and check with F15 the encoding for more info I need to know what is your system CCSID

The lower-right quadrant of the Ring of Light flashes red on the front of your Xbox 360 console. You also receive the following error message in multiple languages on your television screen or monitor:
System Error. Contact Xbox Customer Support. This message begins with an error code in the format "Exx," where xx is a two-digit number.

The following indicator will flash on and off repeated on the front panel of your Xbox 360 console:
Collapse this imageExpand this image
If one red light is flashing and you receive a different error message or error code than those that were described previously or you don’t receive an error message or code, your console may be experiencing a different issue. In this case, see "References/links."

This problem occurs when your Xbox 360 console experiences a hardware failure.

1. Turn off your console, disconnect and reconnect all cables, and then turn on your console.
2. If an Xbox Hard Drive is attached to your console, turn off your console, and then remove the Xbox Hard Drive. Turn on your console, and test for the error. If the error does not reoccur, turn off your console and reattach the Xbox Hard Drive. Run alternate additional tests by having the Xbox Hard Drive connected and disconnected to see whether the error occurs only when the Xbox Hard Drive is connected. For more information if the on-screen alphanumeric error is E67, click the following article number to view the article in the Microsoft Knowledge Base: 917874 (http://support.microsoft.com/kb/917874/ ) One of the lights on the Ring of Light on the front of your Xbox 360 console flashes red and you receive one of the following error codes and message: "E67, or E68, or E69. System Error. Contact Xbox Customer Support"
3. If an Xbox Memory Unit (MU) is plugged in to your console, turn off your console, and then remove the Memory Unit. Turn on your console again, and test for the error. If the error does not reoccur, turn off your console and reinsert the MU. Run alternate tests by having the MU connected and disconnected to see whether the error occurs only when the MU is connected.
4. If this problem continues to occur, contact Xbox Customer Service. Note If the agent cannot help you resolve this problem, you must return your console to Microsoft for repair.

Additional support loadTOCNode(2, 'moreinformation'); If the steps in the previous section did not resolve your issue, your console may have to be repaired. For more information about how to start the online repair process, please visit one of the following Web sites:
U.S. customers - Online console repair
http://support.xbox.com/support/en/us/nxe/LiveIDSignIn.aspx?redirectUrl=http://support.xbox.com/support/en/us/nxe/registerdevice.aspx?step=repair

The lower-right quadrant of the Ring of Light flashes red on the front of your Xbox 360 console. You also receive the following error message in multiple languages on your television screen or monitor:
System Error. Contact Xbox Customer Support. This message begins with an error code in the format "Exx," where xx is a two-digit number.

The following indicator will flash on and off repeated on the front panel of your Xbox 360 console:
Collapse this imageExpand this image
If one red light is flashing and you receive a different error message or error code than those that were described previously or you don’t receive an error message or code, your console may be experiencing a different issue. In this case, see "References/links."

This problem occurs when your Xbox 360 console experiences a hardware failure.

1. Turn off your console, disconnect and reconnect all cables, and then turn on your console.
2. If an Xbox Hard Drive is attached to your console, turn off your console, and then remove the Xbox Hard Drive. Turn on your console, and test for the error. If the error does not reoccur, turn off your console and reattach the Xbox Hard Drive. Run alternate additional tests by having the Xbox Hard Drive connected and disconnected to see whether the error occurs only when the Xbox Hard Drive is connected. For more information if the on-screen alphanumeric error is E67, click the following article number to view the article in the Microsoft Knowledge Base: 917874 (http://support.microsoft.com/kb/917874/ ) One of the lights on the Ring of Light on the front of your Xbox 360 console flashes red and you receive one of the following error codes and message: "E67, or E68, or E69. System Error. Contact Xbox Customer Support"
3. If an Xbox Memory Unit (MU) is plugged in to your console, turn off your console, and then remove the Memory Unit. Turn on your console again, and test for the error. If the error does not reoccur, turn off your console and reinsert the MU. Run alternate tests by having the MU connected and disconnected to see whether the error occurs only when the MU is connected.
4. If this problem continues to occur, contact Xbox Customer Service. Note If the agent cannot help you resolve this problem, you must return your console to Microsoft for repair.

Additional support loadTOCNode(2, 'moreinformation'); If the steps in the previous section did not resolve your issue, your console may have to be repaired. For more information about how to start the online repair process, please visit one of the following Web sites:
U.S. customers - Online console repair
http://support.xbox.com/support/en/us/nxe/LiveIDSignIn.aspx?redirectUrl=http://support.xbox.com/support/en/us/nxe/registerdevice.aspx?step=repair (http://support.xbox.com/support/en/us/nxe/LiveIDSignIn.aspx? redirectUrl=http://support.xbox.com/support/en/us/nxe/registerdevice.aspx? step=repair)

Outside the United States - Online console repair
http://www.xbox.com/support/ (http://www.xbox.com/support/) Note Online console repair service is currently not available in all countries and regions. For more information about how to contact Xbox Customer Support directly, please visit the following Microsoft Web site:
http://www.xbox.com/support/contact

I suggest go to Start/Settings/Control Panel/Add remove programs.
Check and see if the program is in list and remove it. While in control panel go to system/Device Drivers check non have a yellow mark on them if so reinstall drivers or upgrade Reboot and try again.