I need to use video button to get my tv on

Here are the steps to program your YK524-01 remote to your Toshiba TV using a code:

1. Turn on your Toshiba TV.
2. Press and hold the "TV" button on your YK524-01 remote until the LED light blinks twice.
3. Enter one of the following 3-digit codes for Toshiba TVs: 115, 125, 136, 156, 159, 160, 170, 179, 185, 195, 204, 216, 218, 227, 228, 229, 231, 233, 235, 236, 238, 239, 240, 241, 242, 243, 244, 245, 246, 247, 248, 249, 250, 251, 252, 253, 254, 255.
4. Press the "Power" button on your YK524-01 remote. If your Toshiba TV turns off, the code has been successfully programmed. If your Toshiba TV does not turn off, repeat steps 2 to 4 with a different code from the list.

If none of the codes work, you can try the automatic code search method:

1. Turn on your Toshiba TV.
2. Press and hold the "TV" button on your YK524-01 remote until the LED light blinks twice.
3. Press and release the "Power" button on your YK524-01 remote.
4. Press the "CH+" button repeatedly until your Toshiba TV turns off.
5. Press and release the "TV" button on your YK524-01 remote to save the code.

I hope this helps!

The 4-digit code to program a universal remote to work with a RCA LED32B30RQ TV model is likely to be one of the following:
11447 11758 11442
To program the universal remote to work with the RCA LED32B30RQ TV:

1. Turn on the TV
2. Press and hold the "Setup" button on the universal remote until the "TV" button blinks twice.
3. Press the "TV" button on the remote.
4. Enter the 4-digit code for your TV using the number buttons on the remote.
5. Press the "Power" button on the remote. The TV should turn off.
6. Press the "Setup" button again to lock in the code.

If the TV does not turn off after entering the code, please try the other codes listed above. If none of the codes work, you may need to refer to the universal remote manual or contact the manufacturer for further assistance.
Note: The method to program the universal remote may vary depending on the remote brand and model

First understand that you need a little patience with this remote, it's a little slow, it may take a few seconds in between pushing buttons for it to react to your TV.

1)
-Turn on TV manually first.

we're going to try and get the remote paired to your particular tv

2)
-Facing RCA universal remote towards TV, press and hold both the POWER and TV buttons on the remote at the same time.. until the RCA universal remote POWER button lights up and is constantly on.

-Then press the PLAY button on RCA universal remote

(POWER button on remote should be blinking after pressing PLAY -- what the remote is doing is trying to program your TV with a list of codes. if your TV does not automatically shut off after a minute, press the PLAY button again. your TV should shut off. wait a few seconds before trying to press PLAY button again if you need to try again.)

3)
Assuming remote turned off TV. Now let's try to get the remote to turn on your TV

On the remote at top right is a REVERSE button, press that. You should see the POWER button on the remote blink once in response to you doing that.

Watch for the power on light on your TV.. your TV may take a few seconds to power on..

Wait a couple seconds. if your TV has not turned back on, press the REVERSE button again. the POWER button should blink once again in response

If your TV did not turn on. You may have to repeat pushing the REVERSE button waiting a couple seconds for the remote to try turning on your TV. For some people this can take several times, if not a dozen times. Just be sure to be patient and wait a couple seconds in between pressing the REVERSE button again. (what the RCA universal remote is doing is going through a list of codes trying to find the right model to pair to)

4)
Assuming the remote finally turned on your TV.. We are almost done. We programmed the remote to turn off the TV and turn on the TV. now we want to press the STOP button on the RCA universal remote to lock in those codes into the remote. After pressing the STOP button the light on the remote POWER button should turn off.

5)
We are done. You should be able to change the channels and raise and lower the volume of your TV.
###

HOW TO RESET YOUR TV REMOTE CONTROL - TV REMOTE CONTROLS AMAZING SECRET

Is the blinking red light on the TV or the converter box (or maybe on the remote control)? We just need more complete information to answer your question. If the red light is on your remote control look for a button that is stuck in the down position (it's usually the OK button on my remote!).

Ok to reprogram the remote and this only works if you just use the remote for the tv and the receiver. Like i was saying to reprogram the remote hold the tv button till all the top lights flash, then push the red power button, then hit the up arrow button slowly til the tv cuts off, once it cuts off hit the pound (#) button. The top lights should blink three times, that should reprogram the remote, If it is a tv/vcr combo or a tv/dvd combo then there isnt a code for it. Also there is a series of years that the rca tv's wont take a full code and u can just control the power and the tv channel

The codes are, 0145,1145,...Step 1. Turn the TV on. 2. Press the TV button. 3. Press and hold the SET button until the LED blinks twice, then release. 4. Enter one of the four digit codes, the LED will blink twice. 5. Aim the remote at the TV and press the POWER button, if your remote does not have a power button, press PLAY, the TV should turn off, if not, try steps 1-5 again using a different code....hope this was helpful...

Take out the battery for an hour or so.All the codes will erase out of the rca universal remote.

Need actual Mfg. so I can have Comcast program the Remote??? Comcast has NO listing for the program numbers for Vivitek.

the instructions are on the back of the remote. if lost. you have to:
1) Turn tv on ( i would suggest turning it off then on)
2) Press the Device you want to sync (tv)
3) Press and hold the setup button it will blink once...let it blink twice before you go to the next step.
4) press 9-9-1
5) press the power key on the remote
6) press the channel up (CH +) button repeatedly until the device (tv) turns off.
7) when it cuts off immedieately press the setup button.