Question about RTO Safety Vacuum Release System - SR-500 Stingl Switch

2 Answers

Keeps turnung off and beeping

Error 17

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 1 Answer

This happens a lot at the pool I guard. If the switch shuts the pump off, when you have it restart the pump, it tries about 3 times to restart the pump and then it displays the error 17 message. I'm not sure what the message means but the switch apparently causes the pump to lose it's prime during restart. You reprime the pump by opening the trap (boxy thing with a see through plastic lid) and sticking a hose in the pipe to the pump until the trap is overflowing. Today someone who didn't know about stingl switches attempted to vacumn the pool without it being in maitenence mode and of course it immediately shut off (so at least the darn thing does it's job). After I pressed the on button it tried to restart 3 times and displayed the error 17 message. So, I reprimed the pump and the pump restarted on the second try. Note that sometimes it will seem to have restarted but the Stingl switch is still in start mode. I'm not sure if it is caused by a timer or because it doesn't like the amount of pressure but the switch often shuts the pump down because it thinks the pump isn't fully running or something. The switch will display "pump on" when everything is normal.

Hope this helps,

dru

Posted on Jul 06, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

You have to know what the code is. It could be that your delta-p is off reference. If you watch the screen it will tell you what the code is.

Posted on Aug 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does this Lenovo IdeaPad P500 error code mean: WWB00800-HL9V6G


Beep and no beep symptoms - Lenovo Support

support.lenovo.com/us/en/documents/ht035729

LenovoFeb 23, 2015 - See Numeric error codes for more help. Two short beeps and a blank screen. System board; DIMM. Three short beeps, pause, three more short ...

Numeric error codes - ThinkPad General - Lenovo Support ...

https://support.lenovo.com/documents/migr-42321-kr

LenovoJun 17, 2014 - If you are unable to find your particular symptom or error, please refer to Need more help? Notes: The most likely cause is listed first. A numeric ...

Lenovo s405 blue screen error code 0xc000000f - Lenovo Community

forums.lenovo.com > ... > Lenovo U and S Series Notebooks

Aug 20, 2013 - 3 posts
When it is turned on, it shows Your PC needs to be repaired A required device isn't connected or can't accessed error code 0xc000000f You'll. U310 Error Message on Boot Up
Nov 22, 2012
0x80070570 Error Installing Win7 on SSD for Y460
Aug 29, 2011
new disk partioning and one key recover feature - Page 9
Apr 15, 2011
Error 0xc00000e9 While Attempting to Boot
Jan 14, 2011
More results from forums.lenovo.com

Jan 31, 2016 | Lenovo Computers & Internet

1 Answer

The door alarm of my fisher and Paykel E372B fridge goes off when the door hasnt been opened for a number of hours. How can I stop this.


You would notice that when it beeps, there are a series of beeps, which relate to an error code - also, the temperature panel would be most likely flashing the same amount of times the beeping occurs. The code relates to a component failure that the active smart system is having problems with.

For example, 17 beeps would be error code 17 - which relates to the freezer fan is drawing less current than is expected. Either the wiring is open circuit or the fan is faulty.

Feb 18, 2015 | Fisher and Paykel Refrigerators

1 Answer

Why does my Philips 347H E10839 have no picture,chirps like a bird when I turn on?


thats an error code its beeping. sounds like capacitors on psu. google the beeps I.e 3 long one short

Sep 19, 2014 | Televison & Video

1 Answer

Dell studio 1749 has 4 short beeps when trying to start


One Beep (Possible system board failure - BIOS ROM checksum failure)
Two Beep (No RAM detected)
Three Beep (Possible system board failure - Chipset error)
Four Beep (RAM read/write failure)
Five Beep (Real Time Clock failure)
Six Beep (Video card or chip failure)
Seven Beep (Processor failure)
Eight Beep (Display failure)

Feb 12, 2013 | Dell Studio 17 (1749) Laptop black -...

1 Answer

Hi I am working on a abit A 17 mother board it was taken apart by my nephew. I think I have every thing back togather, but when I turn it on it beeps and shows code 92,well I think thats what the l e d box...


Hi, you can download a manual here:

http://www.abit.com.tw/page/en/motherboard/motherboard_detail.php?pMODEL_NAME=AI7&fMTYPE=Socket 478&pPRODINFO=Manual

The fault could be the cpu, wrong type of ram, a faulty ram module
or a fault in the mainboard.
Check all the settings in the manual and the bios aswell.

Here is a list of beep codes:
Basic Beep Codes for ABIT AWARD BIOS Motherboards

  1. No beep at all - this means your motherboard is dead, either due to a defective or underpowered power supply, poorly seated CPU or RAM, or a dead-on-arrival board
  2. One beep - board is working fine
  3. One long beep then machine shuts down - faulty, improperly installed or missing CPU
  4. 1 short(Beep) System booting is normally
  5. 2 short(Beep) CMOS setting error
  6. 1 long - 1 short(Beep) DRAM ERROR
  7. 1 long - 2 short(Beep) Display card or monitor connected error
  8. 1 long - 3 short(Beep) Keyboard Error
  9. 1 long - 9 short(Beep) ROM Error
  10. Long(Beep) continuous DRAM isn't inserted correctly
  11. Short(Beep) continuous POWER supply has a problem
  12. A two-tone siren, generally caused by overheating or out of specification voltages
  13. Four beeps then machine shuts down. This is because this version of the BIOS will shut down your machine if no fan tachometer signal is detected on the fan header. Make sure you attach a fan to the FAN1 or FAN4 header or clear CMOS to reset to default (no checking).

Sep 07, 2011 | Abit AI7 Motherboard

1 Answer

Our frigidaire dryer keeps beeping. Even tho the lint trap is clean. The dryer keeps beeping. Have you heard of this before? If so, what is the solution?


this may help, even though it is not about a Frigidaire:

http://www99.epinions.com/msg/show_~threads/cat_id_~17/id_~8025/forum_id_~409

Oct 23, 2010 | Frigidaire Dryers

2 Answers

Computer shows no display


did you try installing newest drivers from intel/gigabyte website? what you described looks to me as a overheating problem. try running the game with case open. are you running on the integrated GMA graphics or PCI-E graphics card(like geforce, radeon)?

Jul 02, 2009 | Gigabyte Computers & Internet

1 Answer

Kenmore elite washer cycle signal keeps going off an on turing cy


1 Beep/E10--Error: Water doesn't enter Cause: Water supply problem, Check kinks and faucets
1 Beep/E10--Error: Water leaks Cause: Water connections loose,household drain clog,oversudsing. Correct problems.
1 Beep/E10--Error: Dispenser drawer is open Cause: Washer will not operate if drawer is open.
2 Beeps/E20--Error: Water dosen't drain. Cause: Drain is kinked or household clog. Correct.
3 Beeps/E30--Error: Drum overfilled. Cause: Inlet valve,pressure switch or control board failure.Select drain/spin to remove water. Restart.
4 Beeps/E40--Error: Door is open. Cause: Washer will not operate if door is open. Close door.
5 Beeps/E50--Error: Motor is overheated. Cause: Wait 30 minutes to cool down. Restart.
7 Beeps/E70--Error: Cold water doesn't enter. Cause: Hoses crossed,faucet problem.
15 Beeps/EF0--Error: Oversudsing. Cause: Too much detergent,or improper detergent for machine.
15 Beeps/EF0--Error: Hot water doesn't enter. Cause: Hoses crossed,faucet problem.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jan 04, 2009 | Kenmore Washing Machines

1 Answer

Rca tv


Good day.

Your problem points out to the TAC switches of your unit. Better have those pulled out and be replaced.


Regards,


chris

Jul 31, 2008 | RCA F27450 27" TV

2 Answers

I river H329 multi-codec jukebox


Update its firmware. Good luck.

Aug 24, 2006 | iRiver H320 MP3 Player

Not finding what you are looking for?
RTO Safety Vacuum Release System  - SR-500 Stingl Switch Logo

1,569 people viewed this question

Ask a Question

Usually answered in minutes!

Top RTO Pool & Spa Experts

john h

Level 3 Expert

12139 Answers

Jay Finke
Jay Finke

Level 3 Expert

1339 Answers

Ian Kime
Ian Kime

Level 2 Expert

77 Answers

Are you a RTO Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...