Question about Mitsubishi WT-46807 46" Rear Projection Television

1 Answer

Vv 1220 screen shakes

I have a Quasar VV1220 TV/VCR combo and the screen start to shake few weeks ago, keeps doing it lightly even when TV warms can i fix this problem and what part if any I need to repair it..Thanks...

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,694 Answers
Re: vv 1220 screen shakes

Probable bad electrolytic capacitor in vertical circuit.....T.

To get more help from different experts, list your tv in the correct catogory....

All products>Quasar>VV-1220 Standard Television>

Posted on Oct 24, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Zenith z56dc1d dlp tv picture works for about 1 minute then starts shaking and tv shuts off

You may want to get it in a rather warm room and or remove rear cover and use a hairdryer to warm everything up inside the Cabinet--with rear cover off look to see if the fans are dirty etc and if they all come on, if a DLP especially look at the lamp itself and the fan that cools it.

Dec 18, 2012 | Zenith Projection Televisions

1 Answer

Screen shakes and red lines go through screen?

can you tell me the brand and model number of the set?

Dec 04, 2012 | Projection Televisions

1 Answer

My 50 inch panasonic lcd projection keeps going to a black screen then after a few seconds the picture comes back. The green light stays on but is flashing during this time. I have replaced the bulb twice...

check to insure that your input signal is clean,(clean picture) most modern TV`s blank the video if it is deemed of poor quality, also if you are using a VCR and are viewing pirate copy tapes the VCR will output a varying video level output signal to deter pirating of movies, using a video stabilizer between your VCR and your video input may solve this problem for you, check with your user manual as to the light flashing condition in the diagnostic section this will indicate the fault you are experiencing good luck

Apr 25, 2010 | Panasonic PT-50LC13 50" Rear Projection...

2 Answers

RCA d52w20b picture shaking and "hissing" sound.

The grey components are Box capacitors chances are the 0047 2KV box capacitor in front of that heat sink is whats shorted out, very common problem for your model.

Aug 08, 2009 | Projection Televisions

1 Answer

TV picture shaking!!!

You have a Hyper module problem.Very common with these chassis.Toshiba part # 23148024.This part is no longer available,but it can be repaired.I dont know how much electronics training you may have but it`s a pretty detailed job.The hyper board is the silver stand up module inside the unit right behind the external Audio/Video jack panel.There are 11 little capacitors that all need to be replaced.The value of these caps are 10uf @ 16VDC.I do this job for about $245.00 and the unit works fine.Check with your local shop if it is too much for you.If you don`t know what you are doing you can ruin this module then it`s time for a new set.Good luck.

Jan 15, 2009 | Toshiba 42H82 42" Rear Projection...

1 Answer

Turns on and off green LED flashes until TV turns back on.

this is a symptom of a bad lamp. for some reason it won't spit out a lamp error. shaking up the lamp will sometimes fix temporarily but you will find replacing to be the answer. if your tv has a fan error, you will get 4 red blinks.

Dec 09, 2008 | Sony Grand WEGA KDF-60XS955 60" Rear...

1 Answer

Rca hd52w59

ok does the set show a picture durring this whinning
i have ran into this problems .. sometimes it has to do with a coil that is oscillating...ll037 or ll029...the fix for this is simple if it is the problem. dampen the coil with silicon.

Mar 26, 2008 | RCA HD52W59 HDTV Projection Television

1 Answer

Shakey Screen

That problem is caused by defective capacitors on the Hyper Board location UZ01 stamped MVPU14. You will need to have a technican remove the board and replace all the 10 uF @ 16 Volt SMD caps p/n 24619040N found on that board. The Hyper board is no longer available as a part.

Dec 24, 2007 | Toshiba 50H82 50" Rear Projection...

1 Answer

Shaking screen

Check the 9v regulator Ic2p01 on the signal board for correct regulation 8.9 to 9.1 volts. If voltage at the output is under 8.9v, replace the regulator Ic. Always replace C2p05 100 Ufd 16 V on this set and that should take care of the shakes but you may want the tech to go ahead and ESR some of the other troublesome caps throughout the Tv. He'll know what you mean. Many of the 100mf caps replace automatically. Several others will have a questionable ESR and should be replaced. Caps are inexpensive, but probing with an ESR meter is somewhat labor intensive so you miht discuss with the tech just how far you want him to go testing for bad caps.
A Mits is a great Tv and this repair is clearly worth it..

Dec 19, 2007 | Mitsubishi VS-45607 45" Rear Projection...

1 Answer

TV picture shaking!!!

It sounds like the Hyper board is begining to fail....Does the menu shake too?

May 16, 2007 | Toshiba 50HX70 50" Rear Projection...

Not finding what you are looking for?
Mitsubishi WT-46807 46" Rear Projection Television Logo

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Projection Televisions Experts

matt martin
matt martin

Level 3 Expert

1187 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

66518 Answers

Are you a Mitsubishi Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides