Question about Kenmore Dryers

1 Answer

Kenmore Dryer 60982 Runs but No Heat

Kenmore Dryer 60982 (Model 110.60982990) - the dryer runs but does not heat. The heating element does not look burned or broken. Could it be the thermostat Part #3390291 or perhaps the Thermal Cut-off Part #3398671? or the Relay Part #3405281? Please advise -- also how to test any suggested parts. Thanks so much! Ke

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,122 Answers

You can check them all with an ohms meter but i think it is the thermal fuse at the top of the heater box that is bad-mike

Posted on Jun 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Kenmoe dryer, model #110.62512101. it does not heat.


Check the following to address this issue.




1. No power to the dryer
Make sure there's power getting to the dryer. Check for tripped circuit breakers or blown fuses. An electric dryer uses two circuit breakers or fuses, and if only one of two is tripped or blown, the dryer might still run but not heat. Sometimes the power cord disconnects or burns at the dryer, if this is the case, the wiring and the terminal block must be repaired or replaced.

2. Heating element
A burned out heating element will show no continuity when measured with a meter. Replace the element if found defective.

3. Thermal fuse
Most dryers have a thermal fuse, which burns out when the dryer overheats, in which case the dryer will either not run at all or stop heating. The fuse is usually located on the vent duct, inside the dryer. A blown fuse will show no continuity when measured with a meter. Before replacing the fuse, make sure the blower wheel is not broken or clogged, and there is nothing blocking the venting.


Click here to be directed to the parts list and diagram page.

Sep 14, 2009 | Kenmore Dryers

1 Answer

29'' Kenmore electric dryer series 110 not heating up


Check the following to address this issue.(Most common issue will be a burned out thermal fuse.)




1. No power to the dryer
Make sure there's power getting to the dryer. Check for tripped circuit breakers or blown fuses. An electric dryer uses two circuit breakers or fuses, and if only one of two is tripped or blown, the dryer might still run but not heat. Sometimes the power cord disconnects or burns at the dryer, if this is the case, the wiring and the terminal block must be repaired or replaced.

2. Heating element
A burned out heating element will show no continuity when measured with a meter. Replace the element if found defective.

3. Thermal fuse
Most dryers have a thermal fuse, which burns out when the dryer overheats, in which case the dryer will either not run at all or stop heating. The fuse is usually located on the vent duct, inside the dryer. A blown fuse will show no continuity when measured with a meter. Before replacing the fuse, make sure the blower wheel is not broken or clogged, and there is nothing blocking the venting.

Aug 03, 2009 | Dryers

2 Answers

No heat in dryer model # 96591420


Check the following to address this issue.




1. No power to the dryer
Make sure there's power getting to the dryer. Check for tripped circuit breakers or blown fuses. An electric dryer uses two circuit breakers or fuses, and if only one of two is tripped or blown, the dryer might still run but not heat. Sometimes the power cord disconnects or burns at the dryer, if this is the case, the wiring and the terminal block must be repaired or replaced.

2. Heating element
A burned out heating element will show no continuity when measured with a meter. Replace the element if found defective.

3. Thermal fuse
Most dryers have a thermal fuse, which burns out when the dryer overheats, in which case the dryer will either not run at all or stop heating. The fuse is usually located on the vent duct, inside the dryer. A blown fuse will show no continuity when measured with a meter. Before replacing the fuse, make sure the blower wheel is not broken or clogged, and there is nothing blocking the venting.

Jul 31, 2009 | Kenmore Dryers

1 Answer

Kenmore elite , no heat


Check the following to address this issue.




1. No power to the dryer
Make sure there's power getting to the dryer. Check for tripped circuit breakers or blown fuses. An electric dryer uses two circuit breakers or fuses, and if only one of two is tripped or blown, the dryer might still run but not heat. Sometimes the power cord disconnects or burns at the dryer, if this is the case, the wiring and the terminal block must be repaired or replaced.

2. Heating element
A burned out heating element will show no continuity when measured with a meter. Replace the element if found defective.

3. Thermal fuse
Most dryers have a thermal fuse, which burns out when the dryer overheats, in which case the dryer will either not run at all or stop heating. The fuse is usually located on the vent duct, inside the dryer. A blown fuse will show no continuity when measured with a meter. Before replacing the fuse, make sure the blower wheel is not broken or clogged, and there is nothing blocking the venting.

Jul 27, 2009 | Kenmore Elite HE4 Electric Dryer

2 Answers

Our Kenmore model 96292810 clothes dryer has stopped heating. What is the likely problem?


Check the following to address this issue.




1. No power to the dryer(If you have power, skip to the next possible issue)
Make sure there's power getting to the dryer. Check for tripped circuit breakers or blown fuses. An electric dryer uses two circuit breakers or fuses, and if only one of two is tripped or blown, the dryer might still run but not heat. Sometimes the power cord disconnects or burns at the dryer, if this is the case, the wiring and the terminal block must be repaired or replaced.

2. Heating element
A burned out heating element will show no continuity when measured with a meter. Replace the element if found defective.

3. Thermal fuse
Most dryers have a thermal fuse, which burns out when the dryer overheats, in which case the dryer will either not run at all or stop heating. The fuse is usually located on the vent duct, inside the dryer. A blown fuse will show no continuity when measured with a meter. Before replacing the fuse, make sure the blower wheel is not broken or clogged, and there is nothing blocking the venting.

Jul 18, 2009 | Dryers

1 Answer

Kenmore HE4 - no heat


Check the following to address this issue.




1. No power to the dryer
Make sure there's power getting to the dryer. Check for tripped circuit breakers or blown fuses. An electric dryer uses two circuit breakers or fuses, and if only one of two is tripped or blown, the dryer might still run but not heat. Sometimes the power cord disconnects or burns at the dryer, if this is the case, the wiring and the terminal block must be repaired or replaced.

2. Heating element
A burned out heating element will show no continuity when measured with a meter. Replace the element if found defective.

3. Thermal fuse
Most dryers have a thermal fuse, which burns out when the dryer overheats, in which case the dryer will either not run at all or stop heating. The fuse is usually located on the vent duct, inside the dryer. A blown fuse will show no continuity when measured with a meter. Before replacing the fuse, make sure the blower wheel is not broken or clogged, and there is nothing blocking the venting.

Jun 18, 2009 | Kenmore Elite HE4 Electric Dryer

1 Answer

I have a kenmore model 68741 that won't heat. The heating element is good along with the thermo cutoff and hi-limit thermostat. I am getting proper voltage at the heating element.


Most dryers have a thermal fuse, which burns out when the dryer overheats, in which case the dryer will either not run at all or stop heating. The fuse is usually located on the vent duct, inside the dryer. A blown fuse will show no continuity when measured with a meter. Before replacing the fuse, make sure the blower wheel is not broken or clogged, and there is nothing blocking the venting.

A heating element might only be partially burned out, in which case it would still work but will take longer time to dry the clothes. Replace the element if found defective.

Jun 13, 2009 | Dryers

1 Answer

Dryer running but not heating. How do I check heating element?


Check the following to address this non heating issue



1. No power to the dryer
Make sure there's power getting to the dryer. Check for tripped circuit breakers or blown fuses. An electric dryer uses two circuit breakers or fuses, and if only one of two is tripped or blown, the dryer might still run but not heat. Sometimes the power cord disconnects or burns at the dryer, if this is the case, the wiring and the terminal block must be repaired or replaced.

2. Heating element
A burned out heating element will show no continuity when measured with a meter. Replace the element if found defective.

3. Thermal fuse
Most dryers have a thermal fuse, which burns out when the dryer overheats, in which case the dryer will either not run at all or stop heating. The fuse is usually located on the vent duct, inside the dryer. A blown fuse will show no continuity when measured with a meter. Before replacing the fuse, make sure the blower wheel is not broken or clogged, and there is nothing blocking the venting.


Jun 02, 2009 | Whirlpool Dryers

2 Answers

Kenmore 80 series runs but dont blow hot air


Where is the location of the heating element for a Kenmore 80 series dryer heavy duty model # 77834795

Dec 09, 2008 | Kenmore 63942 Dryer

2 Answers

Kenmore dryer 90 series model 66901692


heating element is located at the back of the dryer. if you can see a big coil of wires like a long spring laid back and fort to a duct , that is the heating element.

Feb 19, 2008 | Kenmore 62602 Electric Dryer

Not finding what you are looking for?
Dryers Logo

Related Topics:

520 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Sal De

Level 3 Expert

2699 Answers

Tim Whalen

Level 3 Expert

3074 Answers

yadayada
yadayada

Level 3 Expert

80407 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...