Question about Kenmore 15769 Built-in Dishwasher

1 Answer

Flashing quick rinse light on panel

Appears to be stuck in that mode - open door resets then goes to wash then flashing quick rinse again

Posted by on

  • 4 more comments 
  • wonder dog Nov 30, 2007

    Dishwasher won't start and is flashing "quick rinse". Unplugged it many times to try to reset. It starts a 2 minute countdown and sounds like it wants to start a cycle then starts flashing "quick rinse" again.

  • Anonymous Dec 03, 2007

    Yes I do have same problem. Quick rinse light blinks.

  • Anonymous Dec 17, 2007

    Experiencing quick rinse light also. Please assist.

  • Anonymous Dec 18, 2007

    MY QUICK RINSE LIGHT FLASHES

  • Dennis Barnett
    Dennis Barnett Jan 11, 2008

    where did the numbers come up on the board all i get is flashing lights did not cancel out still not working

  • peacock52 Jul 17, 2008

    I have the same problem and I have tried what was suggested, the only things is that my dishwasher does not have a display like you talked about; so what do I need to look for or try next.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same problem but I found someone wh said that there is a way to reset the dishwasher. I tried it and it has worked so far.

Here is what I did.
Push the Hi-temp and then push the Sani-rinse. Go back and forth multiple times on these two buttons. I found that after a handfull of pushes that a "1" came up on the display. I continued to keep rotating the two buttons and then a "2" came up on the display and the dishwater started it's "drain" phase. I then hit cancel to clear and then I selected the cycle I wanted. The washer started up just as normal at this point.
Good luck!

Posted on Jan 09, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oko 72630. Why is it stuck on rinse cycle?


Could be several reasons:
- Selected the "Night cycle" program (means standing with the drum full of water, reason: too much noise in the spin cycle)
- Set to the "Rinse hold" (means standing with the drum full of water, reason: wrinkles on the clothes)

According to your description I think that this is not a failure otherwise error E20 will be appears on display.

Once the washing programme has come to an end, END illuminates on the programme progress display.
If RINSE HOLD was selected, the display beside the START/ PAUSE button flashes.
1. After a rinse hold, the water must first be pumped out:
- Either press the START/PAUSE button (the water is pumped out and the washing is spun according to the completed programme;
After the START/PAUSE button is pressed again, the spin speed can still also be changed during spinning), or
- Turn the programme selector to PUMP OUT and press the START/PAUSE button (the water is pumped out without spinning),or
- Turn the programme selector to SPIN or SHORT SPIN and press theSTART/PAUSE button (the water is pumped out and the washing is spun or gently spun).
At the end of this programme step, the END indicator will illuminate.
2. Open the door.
As soon as the DOOR indicator lights up green, the door can be opened.

Dado

Aug 15, 2015 | AEG Washing Machines

1 Answer

Why does my washer stop in cycle


Raise and lower your lid six times to reset timers.

Sep 30, 2017 | Speed Queen CTSA0AWN Front Load Washer

2 Answers

My soap dispenser will not open during the wash cycle


Hi,
There is a quick test to verify there is a problem, this test will take about 2 mins. Open the door, close the dispenser (latched), on the control panel itself, push in this order hi temp wash (HTW) than sani *3 times in that order*. So that means HTW-Sani, HTW-Sani, HTW-Sani. What this will do is run a control service mode, all the LED's will light up, close the door and wait until it stops, within about 45 seconds you should hear the dispenser open. If it opens it is functioning normally, if not, it should be replaced.
I hope this helps

I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

Jul 29, 2011 | KitchenAid 24 in. KUDS01FLSS Built-In...

1 Answer

Quick Rinse light was flashing at end of cycle. Opened and closed door and pushed Start. Quick Rinse and Cancel/Drain light are now flashing and machine won't start. Turned off power supply (30 seconds) /...


Ok try this, open the door and then hit these buttons in the following combination. HI TEMP - DRY - HI TEMP - DRY...then close door and press cancel...then wait for the pump to shut down. you should be able to run a cycle after this...If this fails to fix the problem give me the make and model # of the dishwasher, this can normally be found just inside the door.

Jun 22, 2009 | Dishwashers

2 Answers

The hobart lxih is stuck in delime.


To reset or clear delime message, on control board there are 3 buttons. from power off, drawer open, manget on door switch, door closed, hold PROG on board and press the ON key on keyboard. pressing select moves to next poption, up arrow increases setting. step through select until you see delime, settings for LXi are de for disabled, and 1 through 65= x100 cycles. rg if set at 5, after 500 cycles the message apears. To keep the settings and clear the message a delime sequence needs to be run precisely as described.

DO NOT MIX DELIME ACID, RINSE AGENTS OR OTHER ACID WITH BLEACH PRODUCTS, OR HAZAEDOUS GASES WILL FORM.

With machine off, remove rack , close door, press and hold wash/delime key and press ON. Delime will be lit on display, release wash/delime key, and let machine fill. you should then see ADD and DELIME on the display, open the door and add the delime agent following supplier's instructions precisely. close the door, press wash, delime will flash. After delime is complete power is turned off. Inspect the machine and repeat if necessary.
DO NOT LEAVE THE ACID IN ANY LONGER THAN RECOMMEDED.

Jun 18, 2009 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Blinking lights on Front Panel


I've finally tracked down the manual and it the fault code is as follows

"Indicates a fault in the heater or in the thermistor"

You can go into a fault tracing mode by pushing the "Rinse Hold" button five times within 15 seconds. The first, third, fifth and seventh lights will flash when in this mode and you can test the following parts by pressing the corresponding button. I'm going to try the heater test below and assume that if that works the fault must be with the Thermistor. The other tests could be useful for other faults.

User manual found here

Rinse Hold - tests detergent solenoid, detergent flaps open after about 60sec

Pots & Pans - tests Rinse Aid Solenoid, rinse aid will flow down door

Normal Wash - tests water inlet valve, water can be heard entering

Light Wash - tests ventilator solenoid, there will be a click followed by a rattling noise

Quick Wash - tests the heater, the element heats up, WARNING don’t touch element HOT

Temp - tests circulation pump, the pump starts

Dry - test outlet pump, the pump starts

Manual says to push 55 and 65 degree button to exit, I have no idea where those are so will probably just switch off at wall to reset.

Hope this helps someone. I rang ASKO and they said they didn’t know what the fault code meant so either they can’t read or their service sucks, probably a bit of both!

Feb 12, 2009 | Asko D1716 Built-in Dishwasher

1 Answer

Clean light flashing and unit wont run


you can open the lowe racess panel of d/w and you find a techsheet/ trouble shooter, in ther they will explain how to reset a clean light blinkin 7 times.. you can try pushing the "sani-rinse"---"heated dry"--- "sani-rinse" --- "heated dry"... toggling these buttons will triggor a test mode, youl know your in it for all the lights will light, close the door and wait 30 secs or so, the reopen door and cancel cycle, after it runs for 2min it will be ready fro you to start using again.. of the clean light issue returns, id recommned calling for service

Jan 24, 2009 | Whirlpool Dishwashers

1 Answer

START AND DOOR LOCK LIGHTS FLASH REPEATEDLY. MACHINE WILL NOT STA


Replace the door lock mechanism.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jan 08, 2009 | Washing Machines

1 Answer

Lights flashing on clean. Program does not take.


you can open the lowe racess panel of d/w and you find a techsheet/ trouble shooter, in ther they will explain how to reset a clean light blinkin 7 times.. you can try pushing the "sani-rinse"---"heated dry"--- "sani-rinse" --- "heated dry"... toggling these buttons will triggor a test mode, youl know your in it for all the lights will light, close the door and wait 30 secs or so, the reopen door and cancel cycle, after it runs for 2min it will be ready fro you to start using again.. of the clean light issue returns, id recommned calling for service

Jan 07, 2009 | KitchenAid 24 in. KUDS01FLBL Built-in...

1 Answer

Kenmore Oasis Elite---110-27086601


This error only shows in diagnostic mode, with power off choose any buttons except stop and power, press in intervals 5 seconds on and 5 seconds off until 88 appears and all light light up. If the user panel is faulted F 2 will flash in the display, press the same button you used to start diagnostics to jump to the next error code and once through 88 will flash and diagnostics will start. Sometimes once F2 flashes and the machine has not been repaired it will stick at that mode.

Aug 07, 2008 | Kenmore Oasis HE 27082 Top Load Washer

Not finding what you are looking for?
Kenmore 15769 Built-in Dishwasher Logo

382 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Ken Johnston
Ken Johnston

Level 1 Expert

56 Answers

vince

Level 3 Expert

1216 Answers

D. E. Hev

Level 3 Expert

1181 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...