Question about Sony RM-DX450 LCD Remote Control

1 Answer

Connecting issues This remote was compatible with the CDP CX 400 and then one day it stopped working and it will not connect to it.  I know that this remote is intended for the 450 but is it possible to get it working again?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,102 Answers
Re: Connecting issues

Do you know the codes or have you still got the codes you used the first time try http;//

Posted on Oct 31, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I have an Aiwa cx-nma545 w/o the remote. What is the model number to the remote itself? Or do you know how I can replace it?

Remote is no longer available from Aiwa nor most remote resellers. Ebay is your only source. The above link is to one available currently on ebay usa

Aug 18, 2016 | Aiwa Remote Controls

1 Answer

Help I can't programme my elero prp433 Shutter door control unit

Hi Kristian - I have the same control box/receiver and have lost my remotes.

I tried to buy a non-branded remote to program, but they are not compatible with Elero receivers.

During my search I found these instructions which might help you:

Perhaps you could help me? I am looking to connect a new receiver box (which you can get for 35 GBP including 2 new controls) to get around my problem. The issue I'm having is knowing which terminals on the receiver unit's circuit board I am connecting the external receiver box to.

Do you have any instructions at all for your receiver/control unit? If not, would you be so kind as to take off the cover (just undo the 4 screws in each corner) and take some close-up photos of the terminals (see my picture here as an example

I would be extremely grateful!

Aug 06, 2013 | Remote Controls

1 Answer

My sony remote rmt-b119a just stopped working.

It sounds that the remote control need cleaning. With long duration of use, the touch pad rubber might stick on the gaps of tourch pad sensor circuit. You have to open the remote control to clean it. Check this to know more about the procedure to clean and check a remote control.

Dec 27, 2012 | Remote Controls

1 Answer

My remote stopped working for my fan.On the front of the remote it reads that that6 any wall controls hooked in conjuction with this remote control will permanently damage remote. My electrian disconected...

If you had a dimmer switch in conjunction with the fan you probably did burn it up. You have to have motor controls that are compatible. It does take a few days to burn it up. More details please.

Nov 05, 2010 | Universal Remote Control Hampton Bay...

1 Answer

Remote does not work right at certain times of the

Hello massce. My name is Michael Hurst with DISH Network. I see that you are experiencing issues with your remote during a certain time (7pm-10pm). Seems like there is something that is interfering with the signal that the remote is sending to the receiver, what could be causing this issue could be, backlighting or power save mode on LCD TV's, fluorescent lighting in room, or direct sunlight. You can go through an elimination process by turning on your TV and the DISH receiver then slowly turning on other components in the room. If there is a component in the room that makes the remote stop working that would be the cause of the issue. If the component can't be found an upgrade to UHF remote may help remedy the issue so it doesn't continue.

Jun 16, 2010 | DISH Network IR Remote Control

1 Answer

Blank Blue Screen, but buttons still work

I had the same problem and when I took the remote apart the ribbon connecting the lcd screen to the remote controller board was sheared. The remote was dropped and the impact caused two of the traces on the ribbon to tear.

Sep 29, 2009 | Logitech Harmony 890 LCD Remote Control

1 Answer

Compatible TVs

I can help you with your Logitech Harmony 550 remote control.

The Logitech Harmony 550 remote control is programmed through the
Harmony Windows Setup Software.

Once installed, you will simply run the program and select the devices you would like to control from menus. The software finds the right codes for you and loads them into your remote control.

I hope that helps.
Harmony 550 Manual Download
Logitech Harmony Firmware Update
Harmony Win Software Download
Harmony MAC Software Download
Logitech Harmony Safe Mode Fix
Harmony Remote Glow Light Fix

Jun 06, 2009 | Logitech Harmony 550 Remote Advanced...

3 Answers

Software set-up

I had the same issue. If you are using Vista it won't work at all. You can still setup your remote with the program but just unable to update it. Logitech is blaming your internet connection method to take heat of their failure of a program.

Dec 27, 2007 | Logitech Harmony 880 LCD Remote Control

Not finding what you are looking for?
Remote Controls Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Remote Controls Experts

The Knight
The Knight

Level 3 Expert

66518 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers


Level 3 Expert

4518 Answers

Are you a Sony Remote Control Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides