Question about Linksys Wireless-G WRT54G Router

3 Answers

Diag led Hi, I have a WRT54G v3 and I cannot connect to the internet. I had upgraded the last firmware from linksys and since then the router stoped working. Power led is NOT blinking, it is steady, dmz led turns on when I plug the router and then goes off and the diag led turns red. If I press the diag led it will start blinking fast and turn white. I can access to the web configuration, I cannot access to internet either wired or wirelessly. I had already tried hard reset (30 seconds with power off and tehn power on and keep pressure for 10 more seconds) but it keeps turning red the diag. I already tried upgrading again and again but still no response. Can I downgrade to my previoous firmware? I didn't disconected the router while upgrading, I also turned off the windows firewall while doing it and still does not answer. Please, could you tell me what is going on with this router?

Posted by on

  • Nicolas Videla
    Nicolas Videla Oct 24, 2007

    It's normal, it does not blinks. I can access to the web configuration, but that diag led is red, and when I press it it blinks fast and turns white.

×

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 193 Answers

S u can roll back teh firm ware while u doing this the device should be power on should not be distrubed>and while the firm ware downgrading u can see the power light is blinks>and once its study then reboot and check>if its not works change the device>rate me solved if its help full

Posted on Oct 24, 2007

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 34 Answers

Wat about the powerlight in the router....

Posted on Oct 24, 2007

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 244 Answers

H Keliath,

It is advisable to restore your firmware when it is working. maybe it was not fit the new one. Just try to reset your router.


Hope this will be helpful to you.


Best regards,


Philip

Posted on Oct 24, 2007

  • Cheater Cheater Oct 25, 2007

    Hi Kiliath,



    If led activity still the same hold the reset button with 30 seconds before releasing it. Make it sure when you resiting the router please don't off the router.



    Then after reset was done. turn off the router within 5 minutes then turn on it again.



    If all the settings back to each default factory settings please don't attemp to upgrade for what you did last time. It is possible will damage your router.



    Good Luck!





    Philip

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wrt54g driver download


Your ISP modem connects to Linksys internet port. Then your computer connects to any other available port. That's it! 2 connections.


There are no drivers, only firmware. That is because the unit only interfaces via web access. http://192.168.1.1 Here is where you can do firmware upgrades. Good Luck

Sep 25, 2012 | Linksys Wireless-G WRT54G Router

1 Answer

Access linksys wireless-g wrt54g with Nook tablet


Change the wireless network name and then change the key.
Try to connect to the new wireless network and see if that works.
If not then you can try to upgrade the firmware of your Linksys router.
After upgrading the firmware, reset the router and reconfigure it.

Jan 01, 2012 | Linksys Wireless-G WRT54G Router

1 Answer

I have RV082 Router , and Diag Led is constant what to do


Checking the Router's LEDs

The Linksys router's front panel will indicate the status of the connection. After connecting the broadband modem to the WAN or Internet port, the computer to an available numbered port and powering on the router check the lights on the front panel of the router.

The Linksys router's front panel will indicate the status of the connection. After connecting the broadband modem to the WAN or Internet port, the computer to an available numbered port and powering on the router, the following should be lit:
  • 1 - 8 (LAN)
  • DMZ/Internet (WAN2)
  • Internet (WAN1)
  • Diag
  • System
kb16591-001_en.jpg

Checking the Router's LEDs
Step 1:
Make sure the System LED is lit.

NOTE: If the Diag LED doesn't goes off, you need to upgrade the router's firmware. For instructions, click here .

Step 2:
Make sure the LAN 1-8 ports is lit depending on the computers connected to the designated Ethernet port.

NOTE: If the LAN 1-8 port is not lit, make sure that the computer is powered on. You can also try connecting the PC using another working cable.

Step 3:
Make sure the Internet (WAN1) and DMZ/Internet (WAN2) LED is lit.
NOTE: If the Internet or DMZ/Internet LED is not lit make sure the Broadband modem is powered on and that the modem is properly connected to the Ethernet port







You can access the web-based user interface utility of the RV082 by using one of two methods:

  • Through the RV082 IP address (192.168.1.1 by default), or
  • Through its default hostname ("RV082")

1. Open a web browser (Internet Explorer or Netscape Navigator)

· By IP address: Type http://192.168.1.1 (192.168.1.1 is the default IP address of the RV082)

and click Go or press the [Enter] key.

· By Hostname: Type http://RV082 and click Go or press the [Enter] key.

2. When the username and password prompt appears, type admin in both the username and password fields. (admin is both the default username and default password for the RV082).

Nov 08, 2010 | Linksys RV082 Router (RV082-AU)

1 Answer

Looking for an updated firmware version for model WRT54G


Upgrading the router's firmware will give it numerous functions. This includes a more stable connection to the internet.

To upgrade the router's firmware, complete the following steps:

i. Downloading the Firmware
ii. Backing-Up the Router's Settings
iii. Upgrading the Router's Firmware
iv. Completing the Firmware Upgrade
v. Restoring the Router's Settings
vi. Completing the Firmware Upgrade Process

NOTE: Before proceeding with the upgrade, your computer must have an active Internet connection. It is also recommended that you use a wired computer in upgrading the router's firmware.

Nov 06, 2010 | Linksys Wireless-G WRT54G Router

1 Answer

Firmware upgrade was interrupted & now I can't connect to it. I have reset it 3 times & still nothing


TRY
Upgrading the router's firmware will give it numerous functions. This includes a more stable connection to the internet.
To upgrade the router's firmware, complete the following steps:
i. Downloading the Firmware
ii. Backing-Up the Router's Settings
iii. Upgrading the Router's Firmware
iv. Completing the Firmware Upgrade
v. Restoring the Router's Settings
vi. Completing the Firmware Upgrade Process
NOTE: Before proceeding with the upgrade, your computer must have an active Internet connection. It is also recommended that you use a wired computer in upgrading the router's firmware.

Sep 10, 2010 | Linksys Wireless-G WRT54G Router

1 Answer

I lost power and when I unplugged and replugged the router, the only light that come on are the power and diag light


Hi!

You need to folloow the steps below if Diag Led lights keeps on flashing overtime:

Click start then access control panel Go to Local area connection - properties - internet protocol/TCP-IP then use the IP Address: 192.168.1.50 and Subnet Mask:
255.255.255.0. after these download the most recent firmware version for your router that can be downloaded from your router's manufacturer website. Restart your devices after firmware version upgrade.

Should you have any other questions just please leave a message.


Cheers~

Sep 09, 2010 | Linksys Wireless-G Broadband Router

1 Answer

I have a Linksys WRT54G Ver2 router Problems


Try to upgrade the firmware of the router.
Is there any computer connected to the router with the cable.
If not then you will need to connect the computer to the router.
Download the firmware of the router from the manufacturer's website.
enter the model number. select proper version number and download the firmware of the router.
Once you download the firmware, you will need to open the router set up and upgrade the firmware of the router.
After upgrading the firmware, it is recommended that you reset and reconfigure the router.
Click Here for more information about router and networking

Mar 07, 2010 | Linksys Wireless-G WRT54G Router

1 Answer

My linksys router wrt54g worked well for last


if possible, can you go to the linksys support site and doenload a new firmware? then connect with an ethernet cable and update the firmware. If that does not help, it may be time to buy a new one.

Jun 16, 2009 | Linksys Wireless-G WRT54G Router

2 Answers

Linksys router problem


Try a factory reset on the router, in most cases this can be done by holding the reset button on the unit down for 10 or more seconds. Once this is done you may have to enter any settings into the router again.

Also, try download the latest firmware from http://www.linksys.com and upgrade the firmware on the router.

Dec 08, 2008 | Linksys Wireless-G WRT54G Router

Not finding what you are looking for?
Linksys Wireless-G WRT54G Router Logo

479 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2268 Answers

Michael Galve
Michael Galve

Level 3 Expert

1269 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Are you a Linksys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...