Question about Golden Technologies Avenger 4 Wheel Electric Scooter

1 Answer

I have to keep hitting the reset button to get it going

Can you help my scooter as stoped mooving have to keep hitting the reset button

Posted by on

  • Anonymous Mar 27, 2014

    I forgot my password to my Tablet and wanted to see if by hitting the resat button it would fix it and what would it cause?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 41 Answers

Make sure that there is no hair or string wrapped around the wheels

Posted on Jun 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The only lever is the 1 in the back then is in the back position, keeps scooter still. Pushed reset button, nothing happens. It still beeps 5 times, it is a pride go go ultra x 3 wheel, please help


Hi, 5 bleeps implies the issue is related to the brake, check the little micro-switch situated on the side of the brake unit , this can stick fooling the scooter into thinking it still in freewheel mode...

if the rear disconnects away from the frame , check the connection here as well.

Regards
Rob.

www.gewizrepairs.co.uk

Jan 19, 2015 | Pride Health & Beauty

1 Answer

Reset fuse button on my Shopride runner mobility scooter


hi, they do go faulty, what is the amp rating of the fuse ??

at worse the motor or controller could have a fault ,


Regards
Rob

www.gewizrepairs.co.uk

Apr 12, 2014 | Shoprider Health & Beauty

1 Answer

Mcobility scooter


more info, make model, any lights, any power, have you checked you have not knocked the battery terminal off etc.

Oct 24, 2013 | Health & Beauty

1 Answer

Mio moov 300 screen alignment problem


Download the user manual online and look for factory resettings. Follow instructions and it should work. On my Garmin, the same thing happened. On Garmin, you turn the unit off, press and hold the top left corner of your screen, and turn the unit on while pressing the top left corner of the screen. You wait for 10 seconds and a black dot appears and requests you touch it. The dot moves around the screen and you keep touching it. Once done, your screen perimeter is identified and all the letters fall in place when you press them. Good luck!

Dec 02, 2012 | SNK Mio Moov 300 GPS Receiver

1 Answer

Hi my scooter will go then stop but when i mess with the controller it seems to be all right for a little while i cant afford a new one any help will be apperciated than you Donna


My scooter has just stoped working the battery was low but not too low when I shut it off it would not start again. I charged the batteries and the meter shows full charge but it will not run.
I pushed the reset button, still nothing.

Apr 08, 2011 | Golden Technologies Companion II Travel...

1 Answer

Error#5100 comes on my printer and printer stopes


5100 is a carriage error, check the timing strip for contamination(plastic strip about 1/4" in width)
The unit is not homing, check for obstructions[hitting resume button with power for me]

Reset the printers

1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal..

here is the link for other printers: http://www.cyber-ink.com/member-canon.html

Aug 18, 2010 | Canon Office Equipment & Supplies

1 Answer

Status light is red


check the battery connections where they plug into the controller, (under shroud) usually black and white in color. may have worked itself unplugged from the terrain moving them

Apr 01, 2009 | Health & Beauty

1 Answer

My Scooter stoped and will not go. I have a reset button that is out and when I push it in it will not stay. My friends daughter was riding it and may have been on ruff ground. Top meter shows charge but...


 If your ground fault has popped out you probably have a short somewhere. You need to have someone take a look at your batteries,the problem could be there. Find a reputable dealer or a friend or family member with some skills. 

Mar 30, 2009 | Pride New Mobility Legend 4 Wheel Scooter

Not finding what you are looking for?
Golden Technologies Avenger 4 Wheel Electric Scooter Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Golden Technologies Health & Beauty Experts

Robin Hill
Robin Hill

Level 3 Expert

1263 Answers

wcdoc1953
wcdoc1953

Level 2 Expert

278 Answers

Colin Taylor

Level 2 Expert

346 Answers

Are you a Golden Technologies Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...