Question about Jenn-Air Dishwashers
The electrical panel is good in the garage, there is no GFI blown in the kitchen, there is power to all other electrical outlets in the kitchen, but I can't get to the power for the dishwasher. (I will if I need to - it's behind the unit) The dishwasher just stopped working. I didn't notice standing water in it when it died 2 months ago, I think it was dry - I remember the gel pack falling out of the door and onto the floor while I unloaded it ('cuz it wouldn't turn on) but now it's full of nasty brown water in the bottom.
I appreciate the help
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
You think that liquid nails would be too permanent, so you're wondering if I can suggest an adhesive that would 1) not react adversely with the white paint on the glass panel 2) would not dissolve the black rubber-like adhesive (which has let go) that's between the glass panel and the small brackets, and 3) would be strong enough to hold the glass panel, which is where the DW handle/pull is located, and which is subject to stress caused by constant opening and closing.
Different adhesives are available in diferent parts of the country and they are all subject to proper instalation. So I'm going to sugest some guide lines. 1) You're going to have to do a little leg work. You're going to talk to different people in different hardware stores telling them about your three requirements. You'll be surprised at the varying degrees of knowledge. Don't argue, just take notes. 2) Once you've settled on a product it's time to test it. Find a small piece of glass and aply it to metal useing the adhesive. After drying you can tell if it is satisfactory. If not go back to no.1.
3) Once you're happy with the test find a pair of C-clamps and two blocks of wood. Aply adhesive, then using the wood blocks to protect the glass use the C-clamps on each side. Be carefull not to overtighten. Do this with the door horizontally. Just watch the adhesive, when it starts to squeeze out, stop. Make sure the clamps are aplyed evenly. Be carefull. Good luck.
Posted on Oct 01, 2008
There are two possibilities here. First of all make sure the latch is adjusted to close the door tight. IF not, you can adjust it using a screw driver. next, you may have to replace the gasket as these do wear out.
Posted on Nov 03, 2009
Posted on Jan 01, 2010
1. turn breaker off to diswasher. 2. remove bottom access cover. 3. remove cover over electrical connection box on right side. 4. hold each wire nut connector and firmly tug on one wire at at time to make sure none of the wires pull out of the wire connecor nuts. A loose connection here is more common than you might think.
If those are all OK, turn breaker back on and make sure you have power there. (120 volts black to white) If that was OK, then check door latch switch inside door at the top center and wires passing through door at the bottom of the door.
Posted on Jul 26, 2010
Tips for a great answer:
Dec 04, 2013 | Jenn-Air JGS8850 Gas Kitchen Range
Please check the bellow link for the article therein to have a detailed idea:-
Please accept the solution if it's helpful. Do get back to us for any further query.
Oct 04, 2010 | Jenn-Air JES9860 Electric Kitchen Range
May 22, 2010 | KitchenAid 24 in. KUDS02FR Built-in...
Jan 10, 2010 | Dishwashers
Jan 08, 2010 | Kenmore 24 in. 17482 / 17484 / 17489...
Jul 17, 2009 | Jenn-Air JDR8895AAS Dual Fuel (Electric...
Jun 01, 2009 | Jenn-Air JXT8030ADS Kitchen Hood
Mar 28, 2009 | Jenn-Air Dishwashers
Jan 11, 2009 | Jenn-Air JGR8875QDS Gas Kitchen Range
Dec 19, 2008 | Jenn-Air JDR8895AAS Dual Fuel (Electric...
110 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: