Question about Epson Stylus Photo RX700 All-In-One InkJet Printer

1 Answer

RX700 Ink drip reset counter?

Which buttons do I press when turning on my RX 700 after changing the ink pads which will reset ink drip counter? Thanks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Which buttons do I press when turning on my RX 700 after changing the ink pads which will reset ink drip counter? Thanks

Posted on Mar 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Canon pixma mp130" waste


As a short term fix you can reset the counter.

If you reset the waste ink counter without replacing ink absorber, this means that you are may be about to overload ink absorber. If you only do this one time, it may be tolerable. Be careful if you do this more than one time, because it can flood your printer and harm other part.


To reset the ink absorber counter on the MP130

1. Turn on the printer,2. Press the MENU key, and the SCAN, COPY and SCAN again - entered the service mode

3. Select NVRAM ACCESS, pressr OK

4. Select SET ABS-M LEVEL and set value equal to zero

5. Select SET ABS-M LEVEL and set value to zero

6. Turn off the printer POWER button

7. Your printer can now be turned on and is in normal mode


If your absorber is full, call Canon at 732-521-7230 to order the replacement pads for the ink absorber.
If you do not have access to new ink absorber pads, you can extend the life of your current pads by rinsing them thoroughly and allowing them to dry before reinstalling them.
To replace the pad:
1. Open the printer as though you were going to install new
ink cartridges, letting the carrier move to the center of the printing unit. Unplug the printer so that the carrier will remain centered.
2. Locate the waste ink absorbers in their black rubber frame. They will likely be on the right side of your printer, and will be located underneath the area where the ink cartridges rest when the printer is in standby mode.
3. Use a paper napkin or other disposable and absorbent material to soak up any excess ink that may be in the pads by pressing it down onto the top of the frame.
4. Pull the rubber frame free from the printer, wearing gloves to keep your hands clean. Carefully remove the ink absorber pad or pads from the rubber frame.
6. Insert new ink absorber pads firmly into the rubber frame. Replace the rubber frame in its original position and close the printer.
7. Hold down the power button, then plug the printer back in. Continue holding the power button down until the printer begins to reset itself and come online.
8. Wait for the green power light to turn off, then press and release the power button again. It should blink for two to three seconds, then stay lit; this will indicate that the printer has been reset and is ready to print again without errors.
Let me know if you have any other problems or questions. Thanks.

May 18, 2011 | Canon PIXMA MP130 All-In-One InkJet...

3 Answers

Ink absorber is full.. how will i be able to reset it?


Hi,

Follow the steps below.


1.With the printer powered off but connected to a power source, press the Power
button while pressing and holding the Stop/ Reset button.

2.When the Power is lit, press the Stop/Reset button two times while pressing and
holding the Power button.

3.When releasing the Power button and the Stop / Reset button (regardless of order),
the printer will move into a service mode. (Waiting for menu selection)

4.When the on/off lights in green, press the Stop/Reset button the specified number
of time(s) according to the function listed in the table below.
(Each time the Stop/Reset button is pressed, the LED lights alternately in orange
and green, starting with orange.)

note: press 4 times for waste ink counter reset.
The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print (auto teste)
2 times Green EEPROM print (dados da EEPROM)
3 times Orange EEPROM reset (EEPROM reset)
4 times Green Waste ink counter reset (Absorvente reset)

5.Turn off the printer.( it must be turn off) then turn it on again

Good Luck !!!!!!

( In short )

In service mode.
Put Stop/reset 4 times orange => reset waste ink.
Put stop/reset 8 times orange => set level ink.

Regards,
Ron


* Please rate this solution with Thumbs up and Testimony to help us improve providing support

May 13, 2011 | Canon PIXMA MP160 All-In-One InkJet...

2 Answers

Waste ink absorber is full


Hi Good day!!!
Two absorber pads are located on the right side of the printer, under the ink cartridges. With the printer on, lift the top to expose the cartridges. They will automatically move out of the way. You can move them to the left side by hand if the printer is not on. You will probably need a flashlight to see the pads. They each sit in a rubber retainer. The pads can be removed very easily and cleaned. Take the pads out of the retainers with tweezers. They clean up nicely with warm water but you can use something like Simple Green if they are stubborn. It is best to use a spray bottle (on stream) and blast it through the pad until it is white. Sometimes just putting it under a running faucet will do the trick. If there is ink in the rubber retainer after taking the pad out, it can be cleaned up with a paper towel. Put the pads back into the retainers and you have successfully cleaned the ink absorbers. Now you may have to reset the error message so you can get back to printing. This is how to do it.

Following is the procedure to reset the waste ink counter for the Canon Pixma MP150

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)note: press 4 times for waste ink counter reset.

The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset

5) Turn off the printer.( it must be turn off)
then turn it on again.

Thank you for using FixYa

Don't forget to vote thanks!!!

Nov 19, 2010 | Canon i850 InkJet Photo Printer

2 Answers

End of service life error message epson inkjet printer RX700


This refers to the internal counter, actually located in the software on the computer determing that your waste ink pads are likely saturated and need replacement. You can download software from either Epson at http://www.epson.com/cgi-bin/Store/support/InkPadsForm.jsp or at http://www.ssclg.com/download/sscserve.exe. Both of these software packages will allow resetting the counter. However one should either take the printer in to an authorized Epson or independent printer service company or if comfortable with messing around inside computers and peripherals, one can check the waste ink pad(s). On the RX700 there is a small access panel, on the back of the unit, on the left hand side when facing the back of the RX700. It is held in place with a Phillips head screw and small plastic latch tab on its bottom side. The pad material is clearly visible from here, with a pair of clear plastic waste ink tubes directed down into this waste ink receptacle. If this is saturated, wet and discolored, it should be replaced, before resetting the counter. Not doing so risks the excess waste ink overflowing and making a mess and possibly even shorting out some of the circuitry.

Sep 18, 2010 | Epson Stylus Photo RX700 All-In-One InkJet...

1 Answer

How can I change the ink pads on my Epson Stylus RX 700 and where can I buy them? BD


Replacing the ink cartridges
When the ink is empty refer to your lcd panel message to check which one is empty
open the carriage covers
Remove the empty ink cartridge
replace it with your new cartridge

You can get new ink cartridges from here
http://www.inkandmedialtd.co.uk/acatalog/Epson_Stylus_Photo_RX700_Inkjet_Cartridges
or any decent computer stores or computer fair

Mar 31, 2010 | Epson Stylus Photo RX700 All-In-One InkJet...

1 Answer

How to Solve Both Red Light Blinking Problem in Epson R230


Blinking alternately or not? If alternately, see status monitor. It may be end life service (waste ink pad full). Reset waste ink counter using Rx700 adjusment program. If not, it may be a general error.

Nov 12, 2009 | Epson Stylus Photo RX700 All-In-One InkJet...

1 Answer

Waste ink absorber is almost full. How do you empty or replace the waste ink absorber? The printer will no longer print.


if this happens, just turn off the printer plug,then hold the reset\stop button,after that you turn on the plug while pressing the stop reset button, then follow these steps

To reset waste ink counter:
Press Menu-Scan-Copy-Scan to enter service menu.
Use arrow keys to scroll to “Service menu counter access”.
Press OK.
Use arrow keys to scroll to “ABS-M DOT COUNT”
Press Copy.
Use arrow keys to reset count to zero.
Press OK.
Press Stop/Reset.

(optional)

To clean physical pads:
Open cover (as if replacing ink cartridge).
Locate waste ink pads, they are far right under cartridge slider.
Pry up waste ink pads (inky, might want to wear gloves).
Rinse pads in sink or with alcohol, dry.
Replace pads. Make sure pads are fully seated.

Oct 20, 2009 | Canon PIXMA MP130 All-In-One InkJet...

3 Answers

I am getting the warning "Ink absorber full". Is there anythinh I can do on a DIY basis?


Hi

Thanks for using FixYa. Open the cover, move the cartridges to the centre, and then press the pad of absorbent paper towel onto the waste ink pads. You can locate the waste ink pads to the right of the cartridges. This will absorb a lot of ink in the pads and that will remove the warning after you reset the printer waste ink tank counter. You can reset your Canon Printer by following this procedure—

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button 4 times for waste ink counter reset.
5) Turn off the printer.( it must be turn off) then turn it on again.


Please do accept the solution if the issue is resolved or else revert for further assistance.

Thanks
Rylee

Sep 11, 2009 | Canon PIXMA iP1800 InkJet Photo Printer

1 Answer

Canon PIXMA MP110 waste absorber is nearly full


Hi

Thanks for using FixYa. Open the cover, move the cartridges to the centre, and then press the pad of absorbent paper towel onto the waste ink pads. You can locate the waste ink pads to the right of the cartridges. This will absorb a lot of ink in the pads and that will remove the warning after you reset the printer waste ink tank counter. You can reset your Canon Printer by following this procedure—

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button 4 times for waste ink counter reset.
5) Turn off the printer.( it must be turn off) then turn it on again.

Please do rate the solution and revert for further assistance.

Thanks
Rylee

Sep 11, 2009 | Canon Office Equipment & Supplies

2 Answers

Printer won't printer as message says parts are


Part are end life cycle : waste ink pad full. Need to reset waste ink counter. SSc ver 4.3 support RX 620 and 640. U can try using printer model RX 640. Menu Protection Counter, Show current value for checking. Reset protection counter. Or Try to find RX630 adjusment at indoreset,blogspot.com. Don't forget to replace or wash the pad. Or extend outlet waste ink pipe to outside.

Jun 28, 2009 | Epson RX620 All-In-One InkJet Photo...

Not finding what you are looking for?
Epson Stylus Photo RX700 All-In-One InkJet Printer Logo

Related Topics:

978 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Office Equipment & Supplies Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

Are you an Epson Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...